adapter->generation was being incorrectly set as BE_GEN3 for Skyhawk-R.
Replace generation usage with XXX_chip() macros to identify the chip.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not needed anymore.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4 currently uses a too high tx coalescing setting, deferring
TX completion interrupts by up to 128 us.

With the recent skb_orphan() removal in commit 8112ec3b,
performance of a single TCP flow is capped to ~4 Gbps, unless
we increase tcp_limit_output_bytes.

I suggest using 16 us instead of 128 us, allowing a finer control.

Performance of a single TCP flow is restored to previous levels,
while keeping TCP small queues fully enabled with default sysctl.

This patch is also a BQL prereq.
Reported-by: NVimalkumar <j.vimal@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On gcc 4.7, we will get alignment traps in the ip stack if we don't align
the ip headers on receive. The h/w can support this, so use ip aligned
allocations.

Cut down the unnecessary padding on the allocation. The buffer can start on
any byte alignment, but the size including the begining offset must be 8
byte aligned. So the h/w buffer size must include the NET_IP_ALIGN offset.

Thanks to Eric Dumazet for the initial patch highlighting the padding issues.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only generate tx interrupts on every ring size / 4 descriptors. Move the
netif_stop_queue call to the end of the xmit function rather than
checking at the beginning.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupts have already been cleared, so we don't need to clear them
again. Also, we could miss interrupts if they are cleared, but we don't
process the packet.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The standard readl/writel accessors involve a spinlock and cache sync
operation on ARM platforms with an outer cache. Only DMA triggering
accesses need this, so use the raw variants instead in the critical paths.

The relaxed variants would be more appropriate, but don't exist on all
arches.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New received frames will trigger the rx DMA to poll the DMA descriptors,
so there is no need to tell the h/w to poll. We also want to enable
dropping frames from the fifo when there is no buffer.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the tx dma to start reading the next frame while sending the current
frame.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

instead of making separate tg3_napi_disable() and netif_tx_disable() calls.

Update version to 3.126.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed some coding style issues.
Signed-off-by: NKumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

checkpatch.pl throws error message for the current code. This patch fixes
this coding style issue.
Signed-off-by: NKumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: NJitendra Kalsaria <Jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following chips need to enable internal settings to let ASPM
and clock request work.

RTL8111E-VL, RTL8111F, RTL8411, RTL8111G
RTL8105, RTL8402, RTL8106
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use WARN rather than printk followed by WARN_ON(1), for conciseness.

A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression list es;
@@

-printk(
+WARN(1,
  es);
-WARN_ON(1);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building atp.o triggers this GCC warning:
    drivers/net/ethernet/realtek/atp.c: In function ‘set_rx_mode’:
    drivers/net/ethernet/realtek/atp.c:871:26: warning: ‘mc_filter[0]’ may be used uninitialized in this function [-Wuninitialized]

GCC is correct. In promiscuous mode 'mc_filter' will be used
uninitialized in set_rx_mode_8012(), which is apparently inlined into
set_rx_mode().

But it turns out set_rx_mode_8012() will never be called, since
net_local.chip_type will always be RTL8002. So we can just remove
set_rx_mode_8012() and do some related cleanups.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CPSW driver remaps two different IO regions, but fails to unmap them
both. This patch fixes the issue by calling iounmap in the appropriate
places.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: NVitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings recently came up with a better way to handle the kconfig
dependencies for the PTP hardware clocks. This patch converts one new and
one older driver to the new scheme.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After d58d46b5 (r8169: jumbo fixes.) max frame len is stored in
rtl_chip_infos[].jumbo_max for each chip and SafeMtu should be gone.
Signed-off-by: NKirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function name should include '_ether_addr'.
Return type should be bool.
Parameter name should be 'addr' not 'dest' (also matching kernel-doc).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was missed in commit a24006ed
('ptp: Enable clock drivers along with associated net/PHY drivers')
which enabled sfc's clock driver unconditionally.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for the FEC(MX6) that offers time
stamping and a PTP haderware clock. Because FEC\ENET(MX6)
hardware frequency adjustment is complex, we have implemented
this in software by changing the multiplication factor of the
timecounter.
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new file fec_ptp.c will use fec_enet_private to support 1588 PTP
move such structure to common header file fec.h
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch hooks into the CPTS code and adds support for the HWTSTAMP
ioctl. The patch includes code for the CPSW version found in the dm814x
even though the background device tree support for this board is still
missing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a way to configure the CPTS input clock scaling factors
via the device tree.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because time stamping on both external ports of the switch simultaneously
is positively useless from the application's point of view, this patch
provides a DT configuration method to choose the active port.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a driver for the CPTS that offers time
stamping and a PTP hardware clock. Because some of the
CPTS hardware variants (like the am335x) do not support
frequency adjustment, we have implemented this in software
by changing the multiplication factor of the timecounter.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the cpsw driver to operate correctly with both the
dm814x and the am335x versions of the switch hardware.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch lets the CPSW driver remember the version number in order to
support the two different variants already in the wild.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code mixes up the CPSW_SS and the CPSW_WR register naming. This patch
changes the names to conform to the published Technical Reference Manual
from TI, in order to make working on the code less confusing.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding multicast address to ALE table via netdev ops to subscribe, transmit
or receive multicast frames to and from the network
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapt the error path, remove unneeded headers]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>