A small bugfix for up to now unused instruction definitions, and a
somewhat larger update to cover MIPS32R2 instructions.
Signed-off-by: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Clarify comment.
Signed-off-by: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

A proper fix would involve introducing the notion of shared caches but
at this stage of 2.6.17 that's going to be too intrusive and not needed
for current hardware; aside I think some discussion will be needed.

So for now on the affected SMP configurations which happen to suffer from
cache aliases we make use of the fact that a single cache will be shared
by all processors.  This solves the deadlock issue and will improve
performance by getting rid of the smp_call_function overhead.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
The "system type" Kconfig options on MIPS are not consistent.  For
some platforms, only the name is listed while other entries are
prepended with "Support for".  Remove this as it doesn't make sense
when describing the "system type".
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
When debugging a kernel compiled by gcc 4.1 with gdb 6.4, gdb could
not show filename, linenumber, etc.  It seems fixed if I used generic
DWARF_DEBUG macro.  Although gcc 3.x seems work without this change,
it would be better to use the generic macro unless there were
something MIPS specific.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Fix a calculation of saved vector address in trap_low.
    
(damage done by lmo f4c72cc7)
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Rename the 64-bit sc_hi and sc_lo arrays to use the same names
as the 32-bit struct sigcontext (sc_mdhi, sc_hi1, et cetera).
Signed-off-by: NDaniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
 o Implement futex_atomic_op_inuser() operation
 o Don't use the R10000-ll/sc bug workaround version for every processor.
   branch likely is deprecated and some historic ll/sc processors don't
   implement it.  In any case it's slow.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
SETNAME only had a minor defect but probably never had a user and
MIPS_RDNVRAM was unimplemented anyway.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Nothing exciting; Linux just didn't know it yet so this is most adding
a value to a case statement.
Signed-off-by: NChris Dearman <chris@mips.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
The 34K is very much like a 24K on steroids.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
In case of CONFIG_64BIT_PHYS_ADDR, set_pte() and pte_clear() functions
only set _PAGE_GLOBAL bit in the pte_low field of the buddy PTEs,
forgetting to propagate ito to pte_high. Thus, the both pages might not
really be made global for the CPU (since it AND's the G-bit of the
odd / even PTEs together to decide whether they're global or not). Thus,
if only a single page is allocated via vmalloc() or ioremap(), it's not
really global for CPU (and it must be, since this is kernel mapping),
and thus its ASID is compared against the current process' one -- so,
we'll get into trouble sooner or later...  Also, pte_none() will fail
on global pages because _PAGE_GLOBAL bit is set in both pte_low and
pte_high, and pte_val() will return u64 value consisting of those fields
concateneted.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
common/au1000/irq.c was missing a mips_timer_interrupt() prototype,
whereas in common/au1000/time.c the actual mips_timer_interrupt()
implementation was missing an irq_exit() invocation, causing a
preempt_count() leak.
Signed-off-by: NHerbert Valerio Riedel <hvr@hvrlab.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

    
Found by Chris Dearman (chris@mips.com).
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We don't enable the BTB on the ixp2350 as that can cause weird
crashes (erratum #42.)  However, some bootloaders enable the BTB,
which means that we have to disable the BTB explicitly.

Found thanks to Tom Rini.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This reverts commit 5491d0f3.

As per Andi:

  "After some discussion with people who have the affected system it
   seems best to revert for 2.6.17.  It broke a common BIOS workaround
   and PCI-X still doesn't work.  Alternative is for people to change
   the BIOS which seems to be better right now."
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.

This caused problems for UML and some other special programs doing
syscall interception.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: Robert Hentosh <robert_hentosh@dell.com>

Actually, we just stumbled on a different bug found in find_e820_area() in
e820.c.  The following code does not handle the edge condition correctly:

   while (bad_addr(&addr, size) && addr+size < ei->addr + ei->size)
       ;
   last = addr + size;
   if ( last > ei->addr + ei->size )
       continue;

The second statement in the while loop needs to be a <= b so that it is the
logical negavite of the if (a > b) outside it. It needs to read:

   while (bad_addr(&addr, size) && addr+size <= ei->addr + ei->size)
       ;

In the case that failed bad_addr was returning an address that is exactly size
bellow the end of the e820 range.

AK: Again together with the earlier avoid edma fix this fixes
boot on a Dell PE6850/16GB
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: Daniel Yeisley <dan.yeisley@unisys.com>

It is possible to boot a Unisys ES7000 with CPUs from multiple cells, and not
also include the memory from those cells.  This can create a scenario where
node 0 has cpus, but no associated memory.  The system will boot fine in a
configuration where node 0 has memory, but nodes 2 and 3 do not.

[AK: I rechecked the code and generic code seems to indeed handle that already.
Dan's original patch had a change for mm/slab.c that seems to be already in now.]
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: "Jan Beulich" <jbeulich@novell.com>

The PM timer code updates vxtime.last_tsc, but this update was done
incorrectly in two ways:
- offset_delay being in microseconds requires multiplying with cpu_mhz
  rather than cpu_khz
- the multiplication of offset_delay and cpu_khz (both being 32-bit
  values) on most current CPUs would overflow (observed value of the
  delay was approximately 4000us, yielding an overflow for frequencies
  starting a little above 1GHz)
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

From: "Jan Beulich" <jbeulich@novell.com>

When using apic= on the kernel command line, this had no effect for machines
matched by either the ACPI MADT or the MPS OEM table scan. However, when such
option is specified, it should also take effect for this set of systems.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Complaining about the IOMMU not compiled in doesn't make sense
here because it is clearly compiled in.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ia32_setup_arg_pages would ignore the passed in random stack top
and use its own static value.

Now it uses the 8bit of randomness native i386 would use too.

This indirectly fixes mmap randomization for 32bit processes too,
which depends on the stack randomization.

Should also give slightly better virtual cache colouring and
possibly better performance with HyperThreading.
Signed-off-by: NAndi Kleen <ak@suse.de>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Drop cic from the list when seen as dead.
- Fixup the locking, just use a simple spinlock.
Signed-off-by: NJens Axboe <axboe@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
  [AGPGART] VIA PT880 Ultra support.
  [AGPGART] Fix Nforce3 suspend on amd64.
  [AGPGART] Enable SIS AGP driver on x86-64 for EM64T systems

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [[CIFS] Pass truncate open flag through on file open in case setattr fails
  [CIFS] Fix typos in previous fix
  [CIFS] endian fix for new POSIX byte range lock support
  [CIFS] fix memory leak in cifs session info struct on reconnect
  [CIFS] ACPI suspend oops
  [CIFS] Do not limit the length of share names (was 100 for whole UNC name)
  [CIFS] Fix new POSIX Locking for setting lock_type correctly on unlock

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NETFILTER]: PPTP helper: fix sstate/cstate typo
  [NETFILTER]: mark H.323 helper experimental
  [NETFILTER]: Fix small information leak in SO_ORIGINAL_DST (CVE-2006-1343)

on set size to zero.
Signed-off-by: NSebastian Voitzsch <sebastoam/vpotzscj@web.de>
Signed-off-by: NSteve French <sfrench@us.ibm.com>

Signed-off-by: NSteve French <sfrench@us.ibm.com>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NSteve French <sfrench@us.ibm.com>

Signed-off-by: NSteve French <sfrench@us.ibm.com>

Wasn't able to reproduce a hard hang, but was able to get an oops if
suspended the machine during a copy to the cifs mount.  This led to some
things hanging, including a "sync".  Also got I/O errors when trying to
access the mount afterwards (even when didn't see the oops), and had
to unmount and remount in order to access the filesystem.

This patch fixed the oops.
Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: NSteve French <sfrench@us.ibm.com>

during mount. Especially important for some non-Western languages.
Signed-off-by: NSteve French <sfrench@us.ibm.com>

Signed-off-by: NSteve French <sfrench@us.ibm.com>

Added different lifebook-versions and the CF-18 to the corresponding
dmi-table.
Signed-off-by: NKenan Esau <kenan.esau@conan.de>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Remove the numbered SW_* entries from the input system and assign names
to the existing users.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Correct touchpad left & right keys assignments for ALPS_OLDPROTO
that were swapped. Old protocol is used on UMAX ActionBook-530T
notebook.
Signed-off-by: NYotam Medini <yotam.medini@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Signed-off-by: NDmitry Torokhov <dtor@mail.ru>