Replace dev_kfree_skb with dev_consume_skb_any in emacs_start_xmit
which can be called in hard irq and other contexts.

emac_start_xmit always transmits the packet making dev_consume_skb
the appropriate function to call.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Replace dev_kfree_skb with dev_consume_skb_any in _tx_reclaim_skb that
can be called in hard irq and other contexts.

dev_consume_skb is used as _tx_reclaim_skb is called after a packet
has been successfully transmitted.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Replace dev_kfree_skb with dev_consume_skb_any in __ei_start_xmit that
can be called in hard irq and other contexts.

dev_consume_skb is used as in this simple driver the skb is always
immediately consumed, there are no drops.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Replace dev_kfree_skb with dev_consume_skb_any in vortex_start_xmit
as it can be called in hard irq and other contexts.

dev_consume_skb_any is used when vortext_start_xmit directly consumes
the packet instead of dmaing it to the device.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Replace dev_kfree_skb with dev_consume_skb_any in el3_start_xmit
as it can be called in hard irq and other contexts.

dev_consume_skb_any is used as on this simple hardware the
skb is consumed directly by the start_xmit function.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Replace dev_kfree_skb with dev_consume_skb_any in uml_net_start_xmit
as it can be called in hard irq and other contexts.

dev_consume_skb_any is used as uml_net_start_xmit typically
consumes (not drops) packets.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb, ixgbe, ixgbevf, i40e and i40evf.

Anjali provides a i40e/i40evf patch to add Energy Efficient Ethernet
Low Power Idle stats and a fix for i40e to change the string
"Side Band" to "Sideband" for consistency.

Mitch provides 2 patches for i40evf to fix if the driver encounters
an error while communicating with the PF driver, do not shut down the
admin queue unconditionally.  Add an error message when the admin
queue message never completes and fix formatting on another message
that was unnecessarily wrapped.

Mark provides a ixgbe patch and five ixgbevf patches.  Fix a possible
infinite recursion when an adapter is removed and registers all read
as all one's in ixgbe_clear_vmdq_generic() and ixgbe_clear_rar_generic().
Converts macros to static inline functions to align kernel coding standard
and prepare for adding Live Error Recovery (LER) to ixgbevf.  Change the
ethtool register test to use the normal register accessor functions and
eliminate macors used for calling register test functions to make error
exits more clear.  Checks all register reads for adapter removal by checking
the status register after any register read that returns all F's since the
status register will never return 0xFFFFFFFF unless the adapter is removed.

Jacob implements SIOCGHWTSTAMP ioctl for igb which enables user processes
to read the current hardware stamp config settings non-destructively.

Todd adds the initial register read and write for surprise removal (LER)
for igb.

Christian Engelmayer fixes an igb memory leak in the igb_get_module_eeprom()
error handling path.

Ken Ichikawa provides a fix for igb, specifically for 82575 hardware to
specify -1 to the phc_index for ethtool's get_ts_info, otherwise a wrong
value will be set to the phc_index.

Christopher Paasch fixes a null pointer dereference in igb and makes sure
to unset the HAS_MSIX flag when the driver falls back to MSI only.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip_rt_dump do nothing after IPv4 route caches removal, so we can remove it.
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As commit a6e28b34("staging/et131x: use SET_ETHTOOL_OPS
directly"), using a wrapper around SET_ETHTOOL_OPS macro is
not actually required, remove and use SET_ETHTOOL_OPS directly.
Signed-off-by: NWang Weidong <wangweidong1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses two typos in the original driver submission. One derived
from a cut & paste error, and another is a misspelling.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses a portable pointer arithmetic issue in the
original submission found by the kbuild test robot.

config: make ARCH=i386 allyesconfig

   altera_sgdma.c: In function 'sgdma_txphysaddr':
>> altera_sgdma.c:393:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
     dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
                                    ^
>> altera_sgdma.c:394:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
        (dma_addr_t)priv->tx_dma_desc);
        ^
   altera_sgdma.c: In function 'sgdma_rxphysaddr':
>> altera_sgdma.c:403:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
     dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
                                    ^
>> altera_sgdma.c:404:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
        (dma_addr_t)priv->rx_dma_desc);
        ^
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the version number returned by the driver's get regs routine
invoked by ethtool so formatting can be dependent on the version
number returned, and any interesting formatted output can check
the version number for specific types of register data returned.
Signed-off-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
This patch series containes following changes -

* TSO over IPv4 and IPv6, Tx checksum offload for VXLAN
* Rx checksum offload for VXLAN and support for .ndo_{add|del}_vxlan_port
  netdev ops.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds Rx checksum offload support for VXLAN.
Implements .ndo_{add|del}_vxlan_port netdev ops.
Adapter supports only one VXLAN port, so program adapter with
very first UDP port which VXLAN driver is listening to.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds LSO, LSO6 and Tx checksum offload support for VXLAN
encapsulated packets on 83xx/84xx series adapters.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The P1010 device tree restricts the number of
supported interrupt groups to 1, although the eth
controller can support 2 interrupt groups and the
driver assumes the Multi-Group mode ("fsl,etsec2" model).

So, in this case the assumption that the Multi-Group
mode (MQ_MG_MODE) devices always support 2 interrupt
groups is false.  To fix this, a check for the actual
number of interrupt groups enabled in the board's
device tree has been added in gfar_probe for the
"fsl,etsec2" devices.

Without this fix, P1010 based boards claim support for
2 Tx queues to the net stack but only one is actually
allocated, leading to NULL access in xmit.  This issue
was introduced by enabling Single-Queue polling for
the P1010 devices.
(71ff9e3d gianfar: Use Single-Queue polling for
"fsl,etsec2")

Fixes: 71ff9e3dSigned-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipv4_ifdown_dst does nothing after IPv4 route caches removal,
so we can remove it.
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing one 16bit value by another in IP header, we can adjust
the IP checksum by doing a simple operation described in RFC 1624, as
reminded by David.

csum_partial() is a complex function on x86_64, not really suited for
small number of checksummed bytes.

I spotted csum_partial() being in the top 20 most consuming functions
(more than 1 %) in a GRO workload, which was rather unexpected.

The caller was inet_gro_complete() doing a csum_replace2() when
building the new IP header for the GRO packet.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
Included changes:
- use ether_addr_copy instead of memcpy when possible
- implement new multicast packet optimisation
- improve several kerneldoc sections
- minor code cleanups

here you have our patchset for net-next/linux-3.15.  They are 16
patches but most of them are just small cleanups and kerneldoc
improvements.

The only big change is the one from patch 8 to 13 by Linus Lüssing
that introduces a new multicast packets optimisation. This new
component aims to reduce the air overhead by sending multicast packets
as bat-unicast when only one destination exists or by dropping them
directly at the source if the multicast group is totally empty.

In patch 11 Linus introduces an atomic_t variable, that like others
that we already have is only object of write and read, thus making the
atomic characteristic totally useless.  Unfortunately this is part of
our sysfs framework, that helps the developer to introduce new knobs
by using few macros only. For this reason we decided to keep Linus'
new knob for now, but I'd like to let you know that we are in the
process of re-working such framework in order to convert all the
current (useless) atomic_t to boolean in one go.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Add missing documentation for BATADV_DAT_ADDR_MAX and
convert an existing documentation to kerneldoc
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Convert the current documentation for the TT flags in proper
kerneldoc and improve it by adding an explanation for each
of the flags.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

With this patch a node sends IPv4 multicast packets to nodes which
have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets
to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too.

Why is this needed? There are scenarios involving bridges where
multicast report snooping and multicast TT announcements are not
sufficient, which would lead to packet loss for some nodes otherwise:

MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism
for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2
querier behind a bridge then our snooping bridge is potentially not
going to see any reports even though listeners exist because according
to RFC4541 such reports are only forwarded to multicast routers:

-----------------------------------------------------------
            ---------------
{Querier}---|Snoop. Switch|----{Listener}
            ---------------
                       \           ^
                      -------
                      | br0 |  <  ???
                      -------
                          \
                     _-~---~_
                 _-~/        ~-_
                ~   batman-adv  \-----{Sender}
                \~_   cloud    ~/
                   -~~__-__-~_/

I)  MLDv1 Query:  {Querier}  -> flooded
II) MLDv1 Report: {Listener} -> {Querier}

-> br0 cannot detect the {Listener}
=> Packets from {Sender} need to be forwarded to all
   detected listeners and MLDv1/IGMPv1/IGMPv2 queriers.

-----------------------------------------------------------

Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers,
because these protocols have no report suppression: A bridge has no
trouble detecting MLDv2/IGMPv3 listeners.

Even though we do not support bridges yet we need to provide the
according infrastructure already to not break compatibility later.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

With this patch a node may additionally perform the dropping or
unicasting behaviour for a link-local IPv4 and link-local-all-nodes
IPv6 multicast packet, too.

The extra counter and BATADV_MCAST_WANT_ALL_UNSNOOPABLES flag is needed
because with a future bridge snooping support integration a node with a
bridge on top of its soft interface is not able to reliably detect its
multicast listeners for IPv4 link-local and the IPv6
link-local-all-nodes addresses anymore (see RFC4541, section 2.1.2.2
and section 3).

Even though this new flag does make "no difference" now, it'll ensure
a seamless integration of multicast bridge support without needing to
break compatibility later.

Also note, that even with multicast bridge support it won't be possible
to optimize 224.0.0.x and ff02::1 towards nodes with bridges, they will
always receive these ranges.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

With this patch a multicast packet is not always simply flooded anymore,
the behaviour for the following cases is changed to reduce
unnecessary overhead:

If all nodes within the horizon of a certain node have signalized
multicast listener announcement capability then an IPv6 multicast packet
with a destination of IPv6 link-local scope (excluding ff02::1) coming
from the upstream of this node...

* ...is dropped if there is no according multicast listener in the
  translation table,
* ...is forwarded via unicast if there is a single node with interested
  multicast listeners
* ...and otherwise still gets flooded.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

If the soft interface of a node is not part of a bridge then a node
announces a new multicast TVLV: The existence of this TVLV
signalizes that this node is announcing all of its multicast listeners
via the translation table infrastructure.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

The new bitfield allows us to keep track whether capability subsets of
an originator have gone through their initialization phase yet.

The translation table is the only user right now, but a new one will be
added soon.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

With this patch a node which has no bridge interface on top of its soft
interface announces its local multicast listeners via the translation
table.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Some helper functions used along the TX path have now a new
"dst_hint" argument but the kerneldoc was missing.
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Reported-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Reported-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

On some architectures ether_addr_copy() is slightly faster
than memcpy() therefore use the former when possible.
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having
the skb mac header pointer set correctly since the following commit
present in kernels >= 3.9:

"net: reset mac header in dev_start_xmit()" (6d1ccff6)

Therefore this commit removes the according, now redundant,
skb_reset_mac_header() call in batadv_bla_tx().
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Our .ndo_start_xmit handler (batadv_interface_tx()) can rely on having
the skb mac header pointer set correctly since the following commit
present in kernels >= 3.9:

"net: reset mac header in dev_start_xmit()" (6d1ccff6)

Therefore we can safely use eth_hdr() and vlan_eth_hdr() instead of
skb->data now, which spares us some ugly type casts.

At the same time set the mac_header in batadv_dat_snoop_incoming_arp_request()
before sending the skb along the TX path.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

net/batman-adv/network-coding.c:1535:1-7: Replace memcpy with struct assignment

Generated by: coccinelle/misc/memcpy-assign.cocci
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Richard Cochran says:

====================
ptp: dynamic pin control

This patch series introduces a way of changing the auxiliary PTP
Hardware Clock functions (periodic output signals and time stamping
external signals) at run time. In the past on the netdev list, we have
discussed other ways to handle this, such as module parameters and
ethtool. This series implements a new PHC ioctl because that is the
most natural way. Users already activate the auxiliary functions via
the ioctls. The sysfs interface has also been expanded so that the pin
configuration can be programmed using shell scripts.

The first patch adds the new ioctls. The PHC subsystem does most of
the work of maintaining the function-to-pin mapping. Drivers will only
need to allocate and initialize a pin configuration table and also
provide a new method that validates a particular assignment.

Patches 5 and 6 just clean up a couple of issues in the phyter driver,
and the remaining patches actually hook the phyter's pins into the new
system.

* ChangeLog
** V3
   - simplify locking in the set pin logic
** V2
   - fix bug in sysfs code on init error path
   - rename ptp_setpin() to ptp_set_pinfunc()
   - rename .setpin() to .verify() in the driver interface
   - simplify ptp_find_pin() logic
   - use correct test when checking whether the pin with the
     calibration function is being reprogrammed
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver use the new pin configuration method when
programming the periodic output signal.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver to use the new pin configuration method when
programming the external time stamp input signals.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adapts the dp83640 driver to allow reconfiguration of which
auxiliary function goes on which pin. The functions may be reassigned
freely with the one exception of the calibration function.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>