SBC3r26 contains many changes to the Logical Block Provisioning
interfaces (formerly known as Thin Provisioning ditto). This patch
implements support for both the old and new schemes using the same
heuristic as before (whether the LBP VPD page is present).

The new code also allows the provisioning mode (i.e. choice of command)
to be overridden on a per-device basis via sysfs. Two additional modes
are supported in this version:

 - WRITE SAME(10) with the UNMAP bit set

 - WRITE SAME(10) without the UNMAP bit set. This allows us to support
   devices that predate the TP/LBP enhancements in SBC3 and which work
   by way zero-detection

Switching between modes has been consolidated in a helper function that
also updates the block layer topology according to the limitations of
the chosen command.

I experimented with trying WRITE SAME(16) if UNMAP fails, WRITE SAME(10)
if WRITE SAME(16) fails, etc. but found several devices that got
cranky. So for now we'll disable discard if one of the commands
fail. The user still has the option of selecting a different mode in
sysfs.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When debugging DIF/DIX it is very helpful to be able to see which DIX
operation is associated with the scsi_cmnd. Include the protection op in
the SCSI command trace.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

My first attempt was botched, got the wrong PCI Device ID
(used PCI_DEVICE_ID_HP_CISSE, should have been PCI_DEVICE_ID_HP_CISSF)
Signed-off-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This driver is for Broadcom Netxtreme II 57712 chip. The following
patch contains the driver sources for bnx2fc driver.  libfc/libfcoe
changes to enable bnx2fc have already gone through the fcoe
tree. bnx2fc is a SCSI low level driver that interfaces with SCSI
midlayer, libfc, libfcoe, cnic modules.  bnx2fc driver uses services
of libfc for slow path operations such as FIP and fabric
discovery. The fast path IO perations are performed after offloading
the session information to the underlying FCoE firmware.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Reset using "fcoeadm -r" also needs to restart FIP before
doing libfc lport reset, this is needed for new switch firmware
requiring FIP solicitation before doing FLOGI again during reset.
So this patch does this by doing fcoe_ctlr_link_down and then
fcoe_ctlr_link_up to reset the interface.

The fcoe_ctlr_link_down call path also does lport reset
and then fcoe_ctlr_link_up re-starts the fabric login after
doing FIP solicitation first to get reset feature working
again.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Negate has higher precedence than bitwise AND.  FCPHF_CRC_UNCHECKED is
0x1 so the original code is equivalent to: if (!fr_flags(fp)) { ...
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When L2 driver is unloaded, libfcoe_destroy tries to access the fcoe
transport structure matching the netdev. However, since the netdev is
unregistered by that time, it fails to do so. Hence the stale mappings
exists in the fcoe-netdev list. Handle NETDEV_UREGISTER device
notification mechanism to remove the stale fcoe-netdev mapping.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

both fcoe and bnx2fc drivers can access the common definition of
FCOE_MTU.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

EM anchors list initialization for only master port was not enough to
keep npiv working as described here:-
https://lists.open-fcoe.org/pipermail/devel/2011-January/011063.html

So this patch moves fc_exch_mgr_list_clone to update npiv ports
EMs once EM anchors list initialized.

Also some cleanup, no need to set lport = NULL as that always
get initialized later.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When abort for an exchange timed out it didn't release the reference to
the exchange resulting in a memory leak.

After discussion with the author of the patch (CC) that introduced this
bug it was suggested to revert that patch.

This reverts commit ea3e2e72.

Signed-off by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When an fcoe interface is being destroyed; in the process the
fcoe driver will try to release all the resources it had allocated
for that interface including rports. But, it seems that it does not
release the reference held for the name server rport in that process
resulting into a memory leak. This patch fixes that memory leak.
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The following patch for megaraid_sas fixes fault state handling in
megasas_transition_to_ready().
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The following patch fixes an incorrect tasklet_init() call in
megasas_init_fw() to use instancet->tasklet.
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The following patch for megaraid_sas adds a missing check for
MR_EVT_CFG_CLEARED in megasas_aen_polling().
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The following patch for megaraid_sas fixes megasas_probe_one() to
clear MSI-X flags in kdump when the 'reset_devices' kernel parameter
is passed in.
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The following patch for megaraid_sas calls tasklet_schedule() even if
outbound_intr_status == 0 for MFI based boards in MSI-X mode.
Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAdam Radford <aradford@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In some test envirenment, there is loopback topology test. We should
handle this during discovery.
Signed-off-by: NJack Wang <jack_wang@usish.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Instead of blocking the entire host when the port's
queueing limit is hit, we should only block the port's
target. This will allow IO to other ports to execute.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NJames Smart  <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If the port takes a while to transition we could exhaust
the retries when using DID_TRANSPORT_DISRUPTED. For this
case we do not want to use any of the cmd's
retries, because if the command was running then when
it got failed the retry counter was already incremented.
And if this is the first time we are seeing the command,
(it got queued because it slipped through during the race)
then it should not have its retries incremented. The
fc class will decide the correct handling later.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NJames Smart  <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

We'll be using the new version number scheme from now on.
The 'k' in the version in the past will be removed.

The format will be: <major>.<minor>.<sub_minor>.<iter>
A scsi-misc submission increments <sub_minor> and resets <iter>.
An scsi-rc-fixes submission, increments <iter>.
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The fc_block_scsi_eh() might return with status FAST_IO_FAIL
indicating I/O has been terminated due to fast_io_fail timeout.
In this case the rport is still blocked, so any error recovery
will be failing on this port. Hence we need to check if the
return value from fc_block_scsi_eh() is something other than 0,
in which case it should just return with that status.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

If adapter is not online, the driver will not process the response queue, even
on getting an interrupt.
Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Based on reading of the FCP2/4 specification, the driver cannot
expect the storage device to send FCP_RSP information. Instead,
the driver should interpret the data which is present in the frame
to base decisions on the success or failure of the system.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

By not clearing the 'login needed' nor 'login outstanding' states
for an fcport after a big-hammer (adapter reset), the driver may
not properly perform a PLOGI/PRLI sequence (and lose visibility
to the rport) during a follow-on SNS scan.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The additional increment of dsd_seg was causing the compiler to throw an array
out of bounds warning. This patch moves to a direct assignment of
cmd_pkt->fcp_data_dseg_len so that the compiler doesn't generate an array out
bounds warning.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Also in qla_os.c, rename the function, remove DEF_SCSI_QCMD, etc.
Signed-off-by: NMadhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>