Implement common function for locking/unlocking 8 hardware
semaphores used for serializing access to shared resouces
on a NIC board by different PCI functions.

As by definition, callers of these semaphore API can be
put to sleep till the semaphore is locked.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove code for phy access on unreleased NX2031 based quad-gig board.

NX3031 based production quad-gig boards do not require direct phy
access by driver.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of fully initializing an unusable second r6040
device, perform the PHY detection earlier and bail out
in r6040_init_one when we could not read the PHY identifier.
Signed-off-by: NMark Kelly <mark@bifferos.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the unused pioaddr variable.
Signed-off-by: NMark Kelly <mark@bifferos.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Consolidate register definitions in netxen_nic_hdr.h
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement pci driver shutdown functionality, this helps
quiescing all PCI transaction before chipset is reset.

Amit Kumar Salecha <amit@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all tx skb mapping code into netxen_map_tx_skb().
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If netxen_need_fw_reset() return 0 [ implies firmware is up
and running], still go through dma mask check, etc.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ethtool -K knob to control LRO in firmware.
LRO path is completely separated from GRO, LRO packets
are still fed with netif_receive_skb().

Also fix ethtool statistics to include LRO packets.
Also use correct message type while configuring interrupt coalescing.
Signed-off-by: NNarender Kumar <narender.kumar@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The structure, once initialized, never changes.
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Set the USE_INT_PARAM bit so the rx-frames-irq and tx-frames-irq will take
  effect on 5709.
- Increase the default rx-frames to reduce interrupt count.
- Decrease the default rx-frames-irq and tx-frames-irq to catch more events
  during NAPI poll.

All these will reduce interrupts without affecting latency.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report this counter to ethtool -S and include it in netstat.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add flag to expand the workaround to both chips.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unable to allocate memory for new MTU or new ring size, we need
to close the device to prevent it from crashing.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add this check to bnx2_netif_stop() and bnx2_vlan_rx_register() to
prevent bus lockups on some systems when the chip is in low power state.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case IRQs are shared, we will not mistakenly start processing
the ring based on old status block indices.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current mwl8k_priv->fw_lock spinlock doesn't actually protect
against multiple commands being submitted at once, as it is not kept
held over the entire firmware command submission.  And since waiting
for command completion sleeps, we can't use a spinlock anyway.

To fix mwl8k firmware command serialisation properly, we have the
following requirements:
- Some commands require that the packet transmit path is idle when
  the command is issued.  (For simplicity, we'll just quiesce the
  transmit path for every command.)
- There are certain sequences of commands that need to be issued to
  the hardware sequentially, with no other intervening commands.

This leads to an implementation of a "firmware lock" as a mutex that
can be taken recursively, and which is taken by both the low-level
command submission function (mwl8k_post_cmd) as well as any users of
that function that require issuing of an atomic sequence of commands,
and quiesces the transmit path whenever it's taken.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Delete most of the mwl8k_work_struct fields and options, since most
of them are unused or never changed from their defaults:
- We always use priv->config_wq, so delete the wqueue argument from
  mwl8k_queue_work().
- MWL8K_WQ_SPIN and MWL8K_WQ_POST_REQUEST are never used, as all
  callers sleep for request completion, so sleep unconditionally.
- MWL8K_WQ_FREE_WORKSTRUCT is never used.
- MWL8K_WQ_TX_WAIT_EMPTY is always set, so assume it unconditionally.
- timeout_ms/txwait_attempts/tx_timeout_ms are never changed from
  their defaults, so just hardcode these in the workqueue worker.
- step is never used.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Various mwl8k_txq_xmit changes:
- Extract the QoS field before adding the DMA header.
- Only write to tx->status once, and only after all the other
  descriptor fields have been set.
- Do all tx state manipulation under the tx spinlock.
- Remove the priv->inconfig check, as all transmit queues will
  be frozen during config cycles, so we won't ever be asked to
  transmit if a config cycle is running.
- Remove some more dead code.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use MWL8K_TX_QUEUES instead of a hardcoded "4" in a couple of places.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since firmware load commands don't generate 'command done' interrupts
like normal commands do, polling for command done interrupts just
unnecessarily slows down the firmware load process.  Removing this bit
of code speeds up loading a typical firmware image from 840 msec to
180 msec.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding and removing the DMA header that the mwl8k hardware requires
on tx and provides on rx can never fail, since we are guaranteed to
have enough headroom on the tx path to expand the packet, and we only
ever shrink the packet on the rx path.  (And on both paths we are
guaranteed to be the only user of the skb we are handling.)

This allows removing all of the skb clone handling in the tx and tx
reclaim paths, and eliminates error checks in both the tx and rx
paths, simplifying the code a bit more.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to check for NL80211_IFTYPE_MONITOR in
->add_interface(), as this function is never called for monitor
interfaces.  Also, there is no need to advertise this bit in our
wiphy's ->interface_modes.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mwl8k_configure_filter() passes pointers to total_flags and the
multicast address list to a workqueue function, while there is no
guarantee that those pointers will still be valid by the time the
workqueue function runs.

Solve this by passing total_flags by value, and by passing an
already built multicast address setup command packet to the workqueue
function so that we don't have to look at the multicast address list
itself outside of mwl8k_configure_filter().

Also, since ->configure_filter() can sleep now, wait synchronously
for the worker to finish.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>