After considerable testing, the initial fears that the driver might damage
some flavors of RTL8187B hardware seem to be groundless. Accordingly, the
logged warning is removed. In addition, Kconfig is changed to remove the
dependence on EXPERIMENTAL.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Realtek 8187B has a receive command queue to feedback beacon interrupt
and transmitted packet status. Use it to feedback mac80211 about status
of transmitted packets. Unfortunately in the course of testing I found
that the sequence number reported by hardware includes entire sequence
control in a 12 bit only field, so a workaround is done to check only
lowest bits.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add conf_tx callback and use it to configure tx queues of 8187L/8187B.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hin-Tak Leung reported that after the change "rtl8187: add short slot
handling for 8187B" his RTL8187B started to give low throughput on
network transfers. Turns out that the SIFS setting used isn't ok, it
doesn't look to be the real aSIFSTime, using the "magical" 0x22 value
like on other 818x variants as the vendor does too fixes the issue.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Race condition causes RX buffers to be accessed even before it is
initialized. The RX and TX buffers are initialized immediately after
the hardware is registered with mac80211. The mac80211 start callback
is ready to be fired once the device is registered for a case when the
wpa_supplicant is also running at the same time.

The same race condition is also possible for RKFILL registration
as RFKILL init happens after the device registration with mac80211
and it is possible that rfkill_register would be called even before
it is initialized.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k frees irq even before IRQs are disabled and existing IRQs
are flushed when rfkill_register() fails.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, ath9k builds RFKILL feature only when the RFKILL subsystem
is built part of the kernel. Build RFKILL feature regardless of whether
RFKILL subsystem is built as a MODULE or part of the kernel.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes incorrect noise floor threshold values.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

init values update for various atheros chipsets.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables the custom firmware regulatory solution option
on iwlwifi drivers. These devices are uncapable of mapping their
EEPROM regulatory domain to a specific ISO / IEC alpha2.
Although the new 11n devices (>= iwl 5000) have only
3 regultaory SKUs -- MOW, ABG (no N) and BG -- the older
devices (3945 and 4965) have a more complex SKU arrangement
and therefore its not practical to move this to the driver.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fix value of upper FH register bound plus
it reorders and groups registers in more readable way
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up some flow handler related document. It also
removes some blank lines.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch rewrites the mac80211 configure_filter handler to better mapping
mac80211 filter flags to iwlwifi hardware filter flags. We now can support
5 mac80211 filter flags: FIF_OTHER_BSS, FIF_ALLMULTI, FIF_PROMISC_IN_BSS,
FIF_BCN_PRBRESP_PROMISC and FIF_CONTROL. This patch also avoids reconnecting
if the filter flags are changed when the STA is associated. Because rx_assoc
is used when full rxon is not necessary.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes checkpatch.pl errors for iwlwifi.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

use IWL_CCK_RATES_MASK and IWL_OFDM_RATES_MASK instead of
their values directly.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch
1. Removes use once use only fc variables, they are useless after refactoring
ieee80211 frame control handlers
2. Other trivial cleanups
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves code around and group most of the station
management code into iwl-sta.c

No functional changes (yet)
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch aligns iwl3945_pci_probe with iwlwifi's iwl_pci_probe.
Added few comments and code simplified to make readable.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The callback function write_tx_data() can only fail
when our ENTRY_OWNER_DEVICE_DATA flag on a queue entry
failed to determine the entry was not available and
it is in fact still owned by the hardware.
This means that if that function fails the queue
must be stopped in mac80211.

When rt2x00queue_get_queue() returns NULL in the TX
path, it means mac80211 has passed us an invalid queue,
although this should be impossible, it shouldn't hurt
if we send mac80211 a signal to stop the queue either.

Both issues can simply be resolved by removing their
manual failure handler and making them use the failure path
provided in rt2x00mac_tx().
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2500usb and rt73usb have different register word sizes,
for that reason the register access wrappers were never
moved into rt2x00usb.
With rt2800usb on its way, we should favor the 32bit
register access and move those wrappers into rt2x00usb.
That saves duplicate code, since only rt2500usb will
need the special 16bit wrappers.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All code which accessed indirect registers was similar
in respect to the for-loop, the given timeout, etc.
Move it into a seperate function, which for PCI drivers
can be moved into rt2x00pci.

This allows us to cleanup the cleanup the code further
by removing the goto statementsand making the codepath
look a bit nicer.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Call the ath5k pci driver struct "ath5k" too to be less
confusing in sysfs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 4a3e8181.

On request from Alan Cox.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 52429eb2.

On request from Alan Cox.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 7ea3a9ad.

On request from Alan Cox.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change forces the bits to 0 by using an &= operation with an inverted
mask of all options instead of using an |= with a value of 0.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a reference to a Buffer Size extention bit that is unneded by
82575/82576 hardware.  Since it is not needed it should be removed from the
code.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the netlink option for DCB is necessary to actually be useful,
simplified the Kconfig option.  In addition, added useful help text for the
Kconfig option.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Made usb_drivers reset_resume function point to hso_resume this 
fixes problems a usb reset is done when the network interface
is left idle for a few minutes. Possibly reset_resume should
initialise hardware more but this works in the common case.
Signed-off-by: NDenis Joseph Barrow <D.Barow@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Makes TIOCM ioctls for Data Carrier Detect & related functions
work like /drivers/serial/serial-core.c potentially needed 
for pppd & similar user programs.   
Signed-off-by: NDenis Joseph Barrow <D.Barow@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new structure hso_mutex_table had to be declared statically
& used as as hso_device mutex_lock(&serial->parent->mutex) etc
is freed in hso_serial_open & hso_serial_close by kref_put while
the mutex is still in use.

This is a substantial change but should make the driver much stabler.
Signed-off-by: NDenis Joseph Barrow <D.Barow@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added check for IFF_UP in hso_resume, this should eliminate -EINVAL (-22)
errors caused from urb's being submitted twice, once by hso_resume
& once in hso_net_open, if suspend/resume USB power saving  mode is enabled
Signed-off-by: NDenis Joseph Barrow <D.Barow@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved serial_open_count in hso_serial_open to
prevent crashes owing to the serial structure being made NULL
when hso_serial_close is called even though hso_serial_open
returned -ENODEV, Alan Cox pointed out this happens,
also put in sanity check in hso_serial_close
to check for a valid serial structure which should prevent
the most reproducable crash in the driver when the hso device
is disconnected while in use.
Signed-off-by: NDenis Joseph Barrow <D.Barow@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis Joseph Barrow <D.Barow@option.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. convert netdev->priv to netdev_priv().
2. make sbni_pci_probe() be static.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeing previously allocated buffers in case of error.
Signed-off-by: NJirka Pirko <jirka@pirko.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointed out by Joe Perches. Error message after tx_ring allocation check was
wrong.
Signed-off-by: NJirka Pirko <jirka@jirka.pirko.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed typo when allocating rx_ring, tx_ring was checked for null instead.
Signed-off-by: NJirka Pirko <jirka@pirko.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using call by reference use the PTR_ERR macros to handle
return value with error case. Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4e4fd4e4 ("ne2k: convert to
net_device_ops") exported some ei_* symbols from the 8390 library,
but the axnet_cs driver defines local static versions of the same
functions.

Rename them to avoid the namespace conflict.

Reported by Stephen Rothwell.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>