Skip to content

R
raspberrypi-kernel

openeuler / raspberrypi-kernel

通知 13
Star 1
Fork 0
R
raspberrypi-kernel
切换分支/标签
  1. 13 10月, 2007 1 次提交
  3. 21 9月, 2007 1 次提交
  5. 06 9月, 2007 1 次提交
    • D
      [MTD] Fix CFI build error when no map width or interleave supported · 241651d0
      由 David Woodhouse 提交于 
      When building NOR flash support, you have compile-time options for the
bus width and the number of individual chips which are interleaved
together onto that bus. The code to deal with arbitrary geometry is a
bit convoluted, and people want to just configure it for the specific
hardware they have, to avoid the runtime overhead.

Selecting _none_ of the available options doesn't make any sense. You
should have at least one. This makes it build though, since people
persist in trying.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
      241651d0
  7. 23 7月, 2007 1 次提交
  9. 30 6月, 2007 1 次提交
    • K
      [MTD] [OneNAND] 2X program support · ee9745fc
      由 Kyungmin Park 提交于 
      The 2X Program is an extension of Program Operation.

Since the device is equipped with two DataRAMs, and two-plane NAND Flash 
memory array, these two component enables simultaneous program of 4KiB.
Plane1 has only even blocks such as block0, block2, block4 while Plane2 
has only odd blocks such as block1, block3, block5.
So MTD regards it as 4KiB page size and 256KiB block size

Now the following chips support it. (KFXXX16Q2M)
Demux: KFG2G16Q2M, KFH4G16Q2M, KFW8G16Q2M,
Mux:   KFM2G16Q2M, KFN4G16Q2M,

And more recent chips
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
      ee9745fc
  11. 11 5月, 2007 1 次提交
  13. 09 5月, 2007 2 次提交
  15. 08 5月, 2007 1 次提交
  17. 27 4月, 2007 1 次提交
    • A
      UBI: Unsorted Block Images · 801c135c
      由 Artem B. Bityutskiy 提交于 
      UBI (Latin: "where?") manages multiple logical volumes on a single
flash device, specifically supporting NAND flash devices. UBI provides
a flexible partitioning concept which still allows for wear-levelling
across the whole flash device.

In a sense, UBI may be compared to the Logical Volume Manager
(LVM). Whereas LVM maps logical sector numbers to physical HDD sector
numbers, UBI maps logical eraseblocks to physical eraseblocks.

More information may be found at
http://www.linux-mtd.infradead.org/doc/ubi.html

Partitioning/Re-partitioning

  An UBI volume occupies a certain number of erase blocks. This is
  limited by a configured maximum volume size, which could also be
  viewed as the partition size. Each individual UBI volume's size can
  be changed independently of the other UBI volumes, provided that the
  sum of all volume sizes doesn't exceed a certain limit.

  UBI supports dynamic volumes and static volumes. Static volumes are
  read-only and their contents are protected by CRC check sums.

Bad eraseblocks handling

  UBI transparently handles bad eraseblocks. When a physical
  eraseblock becomes bad, it is substituted by a good physical
  eraseblock, and the user does not even notice this.

Scrubbing

  On a NAND flash bit flips can occur on any write operation,
  sometimes also on read. If bit flips persist on the device, at first
  they can still be corrected by ECC, but once they accumulate,
  correction will become impossible. Thus it is best to actively scrub
  the affected eraseblock, by first copying it to a free eraseblock
  and then erasing the original. The UBI layer performs this type of
  scrubbing under the covers, transparently to the UBI volume users.

Erase Counts

  UBI maintains an erase count header per eraseblock. This frees
  higher-level layers (like file systems) from doing this and allows
  for centralized erase count management instead. The erase counts are
  used by the wear-levelling algorithm in the UBI layer. The algorithm
  itself is exchangeable.

Booting from NAND

  For booting directly from NAND flash the hardware must at least be
  capable of fetching and executing a small portion of the NAND
  flash. Some NAND flash controllers have this kind of support. They
  usually limit the window to a few kilobytes in erase block 0. This
  "initial program loader" (IPL) must then contain sufficient logic to
  load and execute the next boot phase.

  Due to bad eraseblocks, which may be randomly scattered over the
  flash device, it is problematic to store the "secondary program
  loader" (SPL) statically. Also, due to bit-flips it may become
  corrupted over time. UBI allows to solve this problem gracefully by
  storing the SPL in a small static UBI volume.

UBI volumes vs. static partitions

  UBI volumes are still very similar to static MTD partitions:

    * both consist of eraseblocks (logical eraseblocks in case of UBI
      volumes, and physical eraseblocks in case of static partitions;
    * both support three basic operations - read, write, erase.

  But UBI volumes have the following advantages over traditional
  static MTD partitions:

    * there are no eraseblock wear-leveling constraints in case of UBI
      volumes, so the user should not care about this;
    * there are no bit-flips and bad eraseblocks in case of UBI volumes.

  So, UBI volumes may be considered as flash devices with relaxed
  restrictions.

Where can it be found?

  Documentation, kernel code and applications can be found in the MTD
  gits.

What are the applications for?

  The applications help to create binary flash images for two purposes: pfi
  files (partial flash images) for in-system update of UBI volumes, and plain
  binary images, with or without OOB data in case of NAND, for a manufacturing
  step. Furthermore some tools are/and will be created that allow flash content
  analysis after a system has crashed..

Who did UBI?

  The original ideas, where UBI is based on, were developed by Andreas
  Arnez, Frank Haverkamp and Thomas Gleixner. Josh W. Boyer and some others
  were involved too. The implementation of the kernel layer was done by Artem
  B. Bityutskiy. The user-space applications and tools were written by Oliver
  Lohmann with contributions from Frank Haverkamp, Andreas Arnez, and Artem.
  Joern Engel contributed a patch which modifies JFFS2 so that it can be run on
  a UBI volume. Thomas Gleixner did modifications to the NAND layer. Alexander
  Schmidt made some testing work as well as core functionality improvements.
Signed-off-by: NArtem B. Bityutskiy <dedekind@linutronix.de>
Signed-off-by: NFrank Haverkamp <haver@vnet.ibm.com>
      801c135c
  19. 18 4月, 2007 1 次提交
  21. 03 4月, 2007 1 次提交
  23. 23 3月, 2007 1 次提交
  25. 09 3月, 2007 1 次提交
  27. 08 3月, 2007 1 次提交
    • V
      [MTD] [NAND] make oobavail public · 1f92267c
      由 Vitaly Wool 提交于 
      During the MTD rework the oobavail parameter of mtd_info structure has become
private. This is not quite correct in terms of integrity and logic. If we have
means to write to OOB area, then we'd like to know upfront how many bytes out
of OOB are spare per page to be able to adapt to specific cases.
The patch inlined adds the public oobavail parameter.
Signed-off-by: NVitaly Wool <vwool@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
      1f92267c
  29. 09 2月, 2007 6 次提交
  31. 07 2月, 2007 1 次提交
  33. 02 2月, 2007 1 次提交
  35. 31 1月, 2007 1 次提交
  37. 18 1月, 2007 2 次提交
  39. 10 1月, 2007 2 次提交
  41. 29 11月, 2006 6 次提交
  43. 16 11月, 2006 3 次提交
  45. 31 10月, 2006 1 次提交
  47. 22 10月, 2006 1 次提交
  49. 04 10月, 2006 1 次提交