The following UART parameters are defined within the UART driver:

1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
    where uart will be disabled after timeout

Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.

This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.

If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: NDeepak K <deepak.k@ti.com>
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

From the runtime callbacks enable hwmod wakeups for uart which will
internally enable io-pad wakeups for uarts if they have rx-pad pins
set as wakeup capabale.

Use the io-ring wakeup mechanism after uart clock gating and leave
the PM_WKST set for uart to default reset values cleanup the
code in serial.c which was handling PM_WKST reg.
Irq_chaing(PRM_DRIVER) is used to wakeup uart after uart clocks are gated
using pad wakeup mechanism.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.

Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.

Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Avoid unconditional context restore every time we gate uart
clocks. Check whether context loss happened based on which
we can context restore uart regs from uart_port structure.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Remove the uart reset function which is configuring the
TX empty irq which can now be handled within omap-serial driver.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Add missing uart regs to uart_port structure which can be used in
context restore. Store dll, dlh, mdr1, scr, efr, lcr, mcr reg values
into uart_port structure while configuring individual port in termios
function.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

The mapbase (start_address), membase(io_remap cookie) part of
pdata struct omap_uart_port_info are removed as this should be
derived within driver.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

Currently we use a shared irq handler to identify uart activity and then
trigger a timer. By default the timeout value is zero and can be set or
modified from sysfs. If there was no uart activity for the period set
through sysfs, the timer will expire and call timer handler this will
set a flag can_sleep using which decision to gate uart clocks can be taken.

Since the clock gating mechanism is outside the uart driver, we currently
use this mechanism. In preparation to runtime implementation for omap-serial
driver we can cleanup this mechanism and use runtime API's to gate uart clocks.

Removes the following:
* timer related info from local uart_state struct
* the code used to set timeout value from sysfs.
* irqflags used to set shared irq handler.
* un-used function omap_uart_check_wakeup.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: NKevin Hilman <khilman@ti.com>

In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.

1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
    path from PM code, this is removed as same is handled by
    uart_suspend_port/uart_resume_port in omap-serial driver which will
    do an port_shutdown on suspend freeing irq and port_startup on resume
    enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
    UART clocks can be gated within driver using runtime funcs
    and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
    driver itself with runtime API. Remove is_suspending check used to acquire
    console_lock.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

This patch adds cpu type, macros for identification of TI814X device.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_TI814X for now]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).

The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.

cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.

In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for detection of the next chip in the OMAP4 family: OMAP4470 ES1.0

For more details on OMAP4470, visit:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12869&contentId=123362Signed-off-by: NLeonid Iziumtsev <x0153368@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

allow for the omap4430 es2.3 revision to be recognized in the
omap4_check_revision() function.

most aspects of all omap4430 es2.x versions are identical, however
a number of small variations such as default pullup or pulldown
resistor configurations vary between revisions.

detailed information on silicon errata for omap4430 revisions can
be found at http://focus.ti.com/pdfs/wtbu/swpz009D.pdfSigned-off-by: NDavid Anders <x0132446@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the common platform files with AM335X device
support (AM33XX family).

The approach taken in this patch is,
AM33XX device will be considered as OMAP3 variant, and a separate
SoC class created for AM33XX family of devices with a subclass type
for AM335X device, which is newly added device in the family.

This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x()
checks will return success on AM335X device.
A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3
to include support for AM33XX build.

Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence
struct clksel_rate.flags, struct prcm_config.flags and cpu_mask
are changed to u16 from u8.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_AM33XX for now]
Signed-off-by: NTony Lindgren <tony@atomide.com>

A generic version should replace this later.

As io.c has become nearly empty, omap_init_consistent_dma_size() is moved
into common.c so that io.c can be removed entirely.
Signed-off-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: NKevin Hilman <khilman@ti.com>

As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.

Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

After the MULTI_IRQ_HANDLER conversion, a couple of global
variables can be removed.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Provide the OMAP2/3 IRQ code with low level handlers that can be used
by platforms using CONFIG_MULTI_IRQ_HANDLER. Though the handlers are
written in C, the compiled code looks very similar to its assembly
counterpart (at least with my gcc 4.4.1).
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Without this patch we get the following error:

arch/arm/mach-omap2/clkt_dpll.c: In function '_dpll_test_fint':
arch/arm/mach-omap2/clkt_dpll.c:98: error: 'struct dpll_data' has no member named 'flags'
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.

The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.

This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.

The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
 unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

There is no use for omap-alsa.h and board-palmz71.c doesn't need it either.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

get_context_loss_count functions return context loss count as u32, and
zero means an error. However, zero is also returned when context has
never been lost and could also be returned when the context loss count
has wrapped and goes to zero.

Change the functions to return an int, with negative value meaning an
error.

OMAP HSMMC code uses omap_pm_get_dev_context_loss_count(), but as the
hsmmc code handles the returned value as an int, with negative value
meaning an error, this patch actually fixes hsmmc code also.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NKevin Hilman <khilman@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to fix a warning with recent dmtimer changes]
Signed-off-by: NTony Lindgren <tony@atomide.com>

When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: NSteve Sakoman <sakoman@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

We don't have cpu_is_omapxxxx SoC detection initialized until
SoC detection is initialized from init_early.

Note that with the common map_io we should no longer need
cpu_is_omapxxxx for ioremap.
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Otherwise we can't do generic map_io as we currently rely on
static mappings that work only because of arch_ioremap.
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This allows us to remove omap hacks for map_io.
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This way we don't need to initialize SoC detection early
and can start using generic map_io.
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This allows removing omap hacks for map_io allowing generic
map_io.

Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.
Signed-off-by: NTony Lindgren <tony@atomide.com>

The way that we detect which OMAP3 chips support I/O wakeup and
software I/O chain clock control is broken.

Currently, I/O wakeup is marked as present for all OMAP3 SoCs other
than the AM3505/3517.  The TI81xx family of SoCs are at present
considered to be OMAP3 SoCs, but don't support I/O wakeup.  To resolve
this, convert the existing blacklist approach to an explicit,
whitelist support, in which only SoCs which are known to support I/O
wakeup are listed.  (At present, this only includes OMAP34xx,
OMAP3503, OMAP3515, OMAP3525, OMAP3530, and OMAP36xx.)

Also, the current code incorrectly detects the presence of a
software-controllable I/O chain clock on several chips that don't
support it.  This results in writes to reserved bitfields, unnecessary
delays, and console messages on kernels running on those chips:

    http://www.spinics.net/lists/linux-omap/msg58735.html

Convert this test to a feature test with a chip-by-chip whitelist.

Thanks to Dave Hylands <dhylands@gmail.com> for reporting this problem
and doing some testing to help isolate the cause.  Thanks to Steve
Sakoman <sakoman@gmail.com> for catching a bug in the first version of
this patch.  Thanks to Russell King <linux@arm.linux.org.uk> for
comments.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Tested-by: NSteve Sakoman <sakoman@gmail.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: NKevin Hilman <khilman@ti.com>

An API which translates a standard hwmod name to corresponding
platform_device is useful for drivers when they need to look up the
device associated with a hwmod name to map back into the device
structure pointers. These ideally should be used by drivers in
mach directory. Using a generic hwmod name like "gpu" instead of
the actual device name which could change in the future, allows
us to:
a) Could in effect help replace apis such as omap2_get_mpuss_device,
omap2_get_iva_device, omap2_get_l3_device, omap4_get_dsp_device,
etc..
b) Scale to more devices rather than be restricted to named functions
c) Simplify driver's platform_data from passing additional fields
all doing the same thing with different function pointer names
just for accessing a different device name.
Signed-off-by: NNishanth Menon <nm@ti.com>
[b-cousson@ti.com: Adapt it to the new pdev pointer inside od,
remove the unneeded helpers, and fold the next patch here]
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Add SoC specific map_io function to be used by the generic DT
board file. This is an intermediate step before having some
generic DT aware map_io function.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This generalizes the omap2_mcbsp1_mux_clkr_src and omap2_mcbsp1_mux_fsr_src
implementation between generic McBSP and OMAP2 specific McBSP code. These
functions are used to select source for CLKR and FSR signals on OMAP2+.

Start generalizing the code by implementing an optional mux_signal function
pointer in platform data that will implement the actual muxing and which is
called now from omap2_mcbsp1_mux_clkr_src and omap2_mcbsp1_mux_fsr_src.
These functions are to be removed later and cleanup the API so that
mux_signal gets its arguments directly from client code.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This generalizes the omap2_mcbsp_set_clks_src implementation between generic
McBSP and OMAP2 specific McBSP code. Currently this function is used to
select either internal fclk or clks pin as a McBSP CLKS source on OMAP2+.

Implement generalization by having an optional set_clk_src function pointer
in platform data that is used to select parent for a given clock. Idea is to
pass higher level source clock name (later coming from client driver) that
platform specific code will map to platform specific clock name.

API cleanup between McBSP and client code comes later.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

These address definitions are OMAP1 specific can be in single source file.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

hardware.h is not needed here and let the definition for struct clk to come
via linux/clk.h.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Sidetone resource is already registered for a device so there is no need
for cpu_is_omap34xx() and McBSP port number tests in the driver. We can
cleanup and make the code generic by dropping remaining CONFIG_ARCH_OMAP3
conditional compilations and then using sidetone resource and st_data
variable for runtime tests.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Active sidetone requires that McBSP interface clock doesn't idle and there
is no mechanism in hwmod to turn autoidling on/off in runtime. McBSP2 and 3
in OMAP34xx share their interface clock with McBSP sidetone module and
that interface clock must be active when the sidetone is operating.

Sidetone has its own autoidle bit which should keep the interface clock
active but it is broken. Putting the McBSP core to no-idle mode when the
sidetone is active is no good either since it results to higher power
consumption when using the threshold based DMA transfers.

For making the McBSP code more generic, move this sidetone clock management
with fixme comments to mach-omap2/mcbsp.c and pass pointer to it via
platform data.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Cc: Paul Wamsley <paul@pwsan.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Rationale here is to remove one global variable and to make possible to have
variable size McBSP register maps inside SoC.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove CONFIG_ARCH_OMAP3 conditional compilation and cpu_is_omap34xx test
around buffer threshold based transfer and DMA operating mode control. Use
instead the buffer_size in platform data to determine when these sysfs
controls are exposed and when to access related McBSP registers. Rationale
for this is to make code generic and to allow to use it on OMAP4 that also
supports threshold based transfers.

Currently buffer_size variable is set only for OMAP3 SoCs but it is easy
to extend to OMAP4 and any later OMAP version.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>