EXPORTed symbols cannot be __init/__devinit.
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If pcie_portdrv_probe() fails but it had already called
pci_enable_device(), then call pci_disable_device() when
returning error.

Is there some reason that this isn't being done?
or was it just missed?
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NHenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Wait until all users have closed their device context before allowing
device unregistration to complete.  This prevents a crash caused by
referring to stale data structures.

A better solution would be to have a way to revoke contexts rather
than waiting for userspace to close the context, but that's a much
bigger change that will have to wait.  For now let's at least avoid
the crash.
Signed-off-by: NJack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove references to the IPoIB IETF working group as it has been closed.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Data corruption has been seen with Mellanox SRP targets when FMRs
create a memory region with I/O virtual address != 0.  Add a
workaround that disables FMR merging for Mellanox targets (OUI 0002c9).
Signed-off-by: NIshai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Protect against srp_reset_device() clearing the req_queue while
srp_reconnect_target() is in progress (note that state change at
the top of srp_reconnect_target() is not sufficient for this since
srp_reset_device() ignores the state).
Signed-off-by: NIshai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Report error code rather than success (0) on failure allocating
timewait_info in ib_send_cm_req().
Signed-off-by: NSean Hefty <sean.hefty@intel.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Define a constant MTHCA_ARRAY_MASK to replace repeated uses of
(PAGE_SIZE / sizeof (void *) - 1) in mthca array code.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mthca_array_clear() does not clear the slot if the used count is
positive. This leads to crashes in mthca_qp_event() since that uses
mthca_array_get() to check that the qp is valid.

Discovered by Ali Ayoub.
Signed-off-by: NMichael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This reverts c182274f commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This reverts bd009496 commit because it
required a newer version of udev to work properly than what is currently
documented in Documentation/Changes.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Apparently some UHCI controllers change the value of the Short Packet
Detect (SPD) bit in the TD status word -- presumably when they receive a
short packet.  This patch (as759) changes uhci-hcd to avoid assuming
that the bit is unchanged; in fact, the driver no longer looks at SPD at
all.

This fixes the second problem reported in Bugzilla #6752.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is another unusual_devs entry (as760) for another Nokia device,
this time the 3250.

From: Mario Rettig <mariorettig@web.de>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as756) fixes a bug in dummy-hcd found by the lockdep
checker.  In one of the code paths, the driver did not disable
interrupts before calling a request completion routine.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If USB=m, USB_GADGET=y, the option USB_GADGET_DUMMY_HCD mustn't be 
offered since selecting it results in a compile error.

This patch fixes kernel Bugzilla #6534 reported by Toralf Frster.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When HZ is set to 250 (new default) or 100, the time span during which
repeated events from the device are ignored could be too small due to
ms->jiffies rounding.  This causes the auto repeat to kick in early making
it impossible for the user to generate individual press/release events. 
Increate the timeout to compensate.
Signed-off-by: NMarko Macek <Marko.Macek@gmx.net>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The RTL8150 driver currently crashes the kernel if the USB lead is unplugged
while the device is active.  The attached patch adds error handling to
tell the network layer that the device has gone away when the device is
unplugged.  With this patch, the device can be plugged and unplugged
to one's hearts' content, without crashing anything.

Oh, I've also added rudimentary suspend and resume methods.
Signed-off-by: NPeter Chubb <peter@gelato.unsw.edu.au>
Acked-by: NPetko Manolov <petkan@nucleusys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This entry has been a mystery for some time. I had sent this patch as an
RFC a while ago, and now we've had two reports of this not being needed,
so I'm removing it.

In the event there are reports of breakage, we should revert this patch,
but add a US_FL_NEED_OVERRIDE flag.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a new unusual_devs flag for when usb-storage needs to ignore
a device that it would otherwise claim.

We need to ignore the ZyXEL G220F as it is a virtual CDROM drive which
includes the windows driver for this USB-WLAN adapter. After the windows
driver is installed on a windows system, it converts it into a WLAN adapter
(by ejecting the virtual disc).

The virtual CDROM is of no interest to Linux users. The zd1211rw driver will
automatically perform the eject operation, we just need to ensure that
usb-storage does not claim the device.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Can you add the USB IDs for the Belkin USB Serial adapter (P/N F5U257)
to the pl2303 driver in the Linux Kernel? Are you the appropriate person
to approach for this?

I recently purchased a Belkin USB Serial adapter (P/N F5U257) and found
that it didn't work. After a bit of experimentation I found that it
works with the pl2303 driver once the ID has been added. See attached
patch to fix this. Also attached is the output from lsusb -v just in
case you require any information from there.


From: Kim Oldfield <luv@oldfield.wattle.id.au>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here's a short patch which adds one PID to the set of devices
supported by the ftdi_sio driver.  The device in question is a
DLP module used as part of a ham radio USB-to-packet adapter.

From: Dave Platt <dplatt@radagast.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This small patch enables a support of "SHARP WS003SH".
"SHARP WS003SH" (usullary called "W-ZERO3") is most polular All-in-one handheld
CellPhone-plus-WindowsMobile5.0 in Japan.

"SHARP WS003SH" has two modes, "Modem" and "ActiveSync".
But, "ActiveSync" mode uses NDIS connection.
Therefore, ipaq.c can only support "Modem" mode.

http://www.sharp.co.jp/ws/ (Japanese Site)
http://greggman.com/edit/editheadlines/2005-12-24.htm

From: Norihiko Tomiyama <norihiko.tomiyama@ctc-g.co.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The high-speed USB SOC only exists on MPC834x family not MPC83xx family.
Signed-off-by: NLi Yang <leoli@freescale.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Dead code.

From: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This device is now supported by sierra.c.

From: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJon K Hellan <hellan@acm.org>
Signed-Off-By: NMatthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The short driver names were not unique,
which prevented the driver from actually loading.

Also, one of the ioctl pointers was missing.
Signed-Off-By: NMatthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMatthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

OHCI updates for AT91 series processors:

 - Get ready for at91sam926x processors (ARMv5tej not ARMv4t)

 - Suspend/resume support now behaves properly

 - In "standby" mode, OHCI can be a source of system wakeup events
   (remote wakeup, device connect/disconnect, etc)

And minor cleanups.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

UDC updates for AT91 series processors:

 - Get ready for at91sam926x processors (ARMv5tej not ARMv4t)

 - Suspend/resume support now behaves properly

 - In "standby" mode, UDC can be a source of system wakeup events
   (host resume, device connect/disconnect, etc)

 - Fix IRQ storming issues, seemingly related to clock disabling
   changes that went in a while back

And minor cleanups, especially whitespace.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Victor  <andrew@sanpeople.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTom Tucker <tom@opengridcomputing.com>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise we allow building appletalk drivers in-kernel when
CONFIG_ATALK is modular.  That doesn't work because these drivers use
symbols such as "alloc_talkdev" which is exported from code built
by CONFIG_ATALK.

Noticed by Toralf Förster.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we introduced -rR then aic7xxx no loger could pick up definition
of YACC&LEX from make - so do it explicit now.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Since we now use the generic backlight infrastructure, I think we need to
call rivafb_bl_init before calling register_framebuffer since otherwise
rivafb_bl_init might race with the framebuffer layer already opening the
device and setting up the video mode.  In this case we might end up with a
not yet fully intialized backlight (info->bl_dev still NULL) when calling
riva_bl_set_power via rivafb_set_par/rivafb_load_video_mode and the kernel
dies without any further notice during boot.

This fixes booting current git on a PB 6,1.  In this case radeonfb/atyfb
would be affected too - I can fix that too but don't have any hardware to
test this on.

Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

CONFIG_FB_NVIDIA already depends on CONFIG_PCI in drivers/video/Kconfig.
Driver does an extra ``sanity check'' which is then redundant.
Signed-off-by: NArthur Othieno <apgo@patchbomb.org>
Cc: Antonino Daplas <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch fixes several problems:
- The legacy backlight value might be set at interrupt time. Introduced
  a worker to prevent it from directly calling the backlight code.
- via-pmu allows the backlight to be grabbed, in which case we need to
  prevent other kernel code from changing the brightness.
- Don't send PMU requests in via-pmu-backlight when the machine is about
  to sleep or waking up.
- More Kconfig fixes.
Signed-off-by: NMichael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>