The DesignWare USB3 core tells us which phase
of a control transfer should be started, it
also tells us which physical endpoint needs
that transfer.

With these two informations, we have all we
need to simply EP0 handling quite a lot and
get rid rid of the SW state machine tracking
ep0 states.

For achieving this perfectly, we needed to
add support for situations where we get
XferNotReady while endpoint is still busy
and XferNotReady while gadget driver still
hasn't queued a request.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add a flag to keep track of ep0 direction.
This flag will be used on a following patch.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In case we have transfers which aren't aligned
to wMaxPacketSize, we need to be careful with
how we start the transfer with the HW. OUT
transfers _must_ be aligned with wMaxPacketSize
and in order to guarantee that, we use a bounce
buffer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This core cannot handle OUT transfers which aren't
aligned to wMaxPacketSize, but that can happen at
least on control endpoint with the USB Audio Class.

This patch adds a bounce buffer to be used on the
case of a non-aligned ep0out request is queued.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The status field of the Transfer Not Read event
is different on Control Endpoints. On this patch
we are just adding the defines to be used on a
later patch which will re-work the control endpoint
handling.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the previous message had too little meaning. Make
it more human readable and use the macro we already
had for extracting the command completion status out
of DEPCMDn register.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if we don't set DMA address to invalid when unmapping,
we might fall in a situation where request buffer
can't be mapped to DMA again.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

trivial patch. No functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

trivial patch, no functional changes
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We may as well fix this potential leak so we don't have to listen to
the static checkers complain.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Without this patch we won't clear that bit and instead will
clear all other bits on our endpoint flag.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Type 6 should be used for the first transfer during an interval. This is
also what the reference driver is using. Type 7 seems to be for following
or additional transfers within the same interval.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If we collected two requests together (i.e. only the last of them has
LST=1) then we only have to stop transfer once: The clean-up code will
cleanup everything until first TRB with the LST bit set.
After XferComplete this index should be no longer valid since there is
no transfer pending.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

A TRB which is dequeued seems to have its HWO bits set to 1. Therefore
we ignore it if we dequeue it after the command is completed.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NMichal Sroczynski <msroczyn@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes rts51x_read_mem, rts51x_write_mem, and rts51x_read_status to
allocate temporary buffers with kmalloc. This way stack addresses are not used
for DMA when these functions call rts51x_bulk_transport.
Signed-off-by: NAdam Cozzette <acozzette@cs.hmc.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the MACH_MX* macros are scheduled for removal, so just depend
on ARCH_MXC instead. The Kconfig text makes it clear on which
SoC the driver runs on.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ARCH_MX1 scheduled for removal. Instead, depend on ARCH_MXC
and make clear in the Kconfig text that only i.MX1 has this
hardware.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB_SERIAL_IPW needs to select USB_SERIAL_WWAN to fix build errors:

ipw.c:(.text+0x333841): undefined reference to `usb_wwan_close'
ipw.c:(.text+0x3339e6): undefined reference to `usb_wwan_open'
ipw.c:(.text+0x333bb9): undefined reference to `usb_wwan_release'
drivers/built-in.o:(.data+0x29dac): undefined reference to `usb_wwan_startup'
drivers/built-in.o:(.data+0x29db4): undefined reference to `usb_wwan_disconnect'
drivers/built-in.o:(.data+0x29dd4): undefined reference to `usb_wwan_write'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix build error when CONFIG_USB_GADGET_DWC3 is not enabled:

ERROR: "dwc3_send_gadget_ep_cmd" [drivers/usb/dwc3/dwc3.ko] undefined!
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now ${LINUX}/drivers/usb/* can use usb_endpoint_maxp(desc) to get maximum packet size
instead of le16_to_cpu(desc->wMaxPacketSize).
This patch fix it up

Cc: Armin Fuerst <fuerst@in.tum.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Erdfelt <johannes@erdfelt.com>
Cc: Vojtech Pavlik <vojtech@suse.cz>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: David Kubicek <dave@awk.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Brad Hards <bhards@bigpond.net.au>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Dahlmann <dahlmann.thomas@arcor.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: David Lopo <dlopo@chipidea.mips.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Jiang Bo <tanya.jiang@freescale.com>
Cc: Yuan-hsin Chen <yhchen@faraday-tech.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: OKI SEMICONDUCTOR, <toshiharu-linux@dsn.okisemi.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Roman Weissgaerber <weissg@vienna.at>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Florian Floe Echtler <echtler@fs.tum.de>
Cc: Christian Lucht <lucht@codemercs.com>
Cc: Juergen Stuber <starblue@sourceforge.net>
Cc: Georges Toth <g.toth@e-biz.lu>
Cc: Bill Ryder <bryder@sgi.com>
Cc: Kuba Ober <kuba@mareimbrium.org>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes this build error:

drivers/usb/dwc3/dwc3-pci.c: In function 'dwc3_pci_init':
drivers/usb/dwc3/dwc3-pci.c:211:9: error: 'THIS_MODULE' undeclared (first use in this function)
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Executing
| testusb -a -c 1 -t 3 -v 421 -s 2048

does not complete on the gadget side.
g_zero enqueues a 4096 bytes long buffer. The host sends 2048bytes which
is a multiple of wMaxPacketSize (either 64 or 512 bytes). The host is
done with sending data but the gadget waits for more.
Since the protocol does not include transfer-length-field sending a
terminating zero packet seems the only way out.
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

MPC832x does not have enough MURAM to do fixed MURAM allocation.
Change to dynamic allocation.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a low or full speed urb in progress is unlinked (or some other error
occurs), the buffer in the transaction translator (part of the hub) might end
up in an inconsistent state. This can make all further low and full speed
transactions fail, unless the buffer is cleared.

The bug can be seen when running the usbtest unlink tests as "set altsetting
to 0 failed, -110", and gets fixed by this patch.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Test the just-initialized value rather than some other one.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
identifier x,y,f!={PTR_ERR,ERR_PTR,ERR_CAST};
statement S;
@@

x = f(...);
(
if (\(x == NULL\|IS_ERR(x)\)) S
|
*if (\(y == NULL\|IS_ERR(y)\))
 { ... when != x
   return ...; }
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove the unused function twl6030_set_phy_clk of twl6030-usb.c.
Signed-off-by: NWanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Makes it possible to use i.e. gpio-vbus to handle vbus events.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb-interrupt is requested before the endpoints are initalised.
If an interrupt happens in the time between request_irq and the init
of the endpoint-data (as seen on the Qisda ESx00 ebook-platforms),
it is therefore possible for the interrupt handler to access endpoint-
data before its creation resulting in a null-pointer dereference.

This patch simply moves the irq request below the endpoint init.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I'll be focussed on this driver and can maintain
it without any problem.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.

Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.

The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.

More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.

While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.

[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

... to check whether we're running on DesignWare
USB3 DRD Controller.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

not to confuse with Table 9-7 in USB 2.0 spec
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1483) improves the ehci-hcd driver family by getting rid
of the reliance on the hcd->state variable.  It has no clear owner and
it isn't protected by the usual HCD locks.  In its place, the patch
adds a new, private ehci->rh_state field to record the state of the
root hub.

Along the way, the patch removes a couple of lines containing
redundant assignments to the state variable.  Also, the QUIESCING
state simply gets changed to the RUNNING state, because the driver
doesn't make any distinction between them.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add supprt for on-chip USB controller for Netlogic XLS MIPS64
SoC processor family.
Changes are:
 - update ehci-hcd.c and ohci-hcd.c to add XLS hcds
 - add ehci-xls.c: EHCI support for Netlogic XLS.
 - add ohci-xls.c: OHCI support for Netlogic XLS.
Signed-off-by: NJayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

- Add EHCI Host controller driver
- Add wrapper that creates resources for host controller driver

v2 - Call clk_put() after clk_disable() in probe function
Signed-off-by: NTanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These messages just clutter the log and provide no useful information to
the user, so make them pr_debug().
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

1) A bug in the usage of time_after() in errata2_function().

2) Clear done_maps just prior to starting a new transfer in
   start_bus_transfer(), instead of just after, when done_map bits might have
   been validly set by the started transfer.
Signed-off-by: NArvid Brodin <arvid.brodin@enea.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>