- Use new routing input defines in em28xx-cards.c
- Fix S-Video settings for tvp5150-based cards (input was copied from saa7115
  based cards and worked only because S-Video was selected in the default: case)
- Replace VIDIOC_S_INPUT by VIDIOC_INT_S_VIDEO_ROUTING in em28xx-video.c
- Remove the now obsolete VIDIOC_S_INPUT handler in saa7115.c
- Add VIDIOC_INT_G/S_VIDEO_ROUTING in tvp5150.c
- Add new media/tvp5150.h with the routing defines.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Some saa7115-based cards use a different crystal frequency and a different
audio clock generation. Add a new VIDIOC_INT_S_CRYSTAL_FREQ command to be
able to set these values.
Also change the default APLL setting to 0. It makes no sense to have the
audio clock independent from the video clock, this can lead to audio/video
synchronization problems. Setting this to 0 is also consistent with the old
saa7114.c source and the way the Hauppauge Windows driver sets it.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- improve handling of the EXTERN input: don't start an unnecessary carrier scan
- improve the LOG_STATUS output
- ensure that a carrier scan is started again when switching back to the tuner.
- set correct prescale for L-NICAM
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There is some old code in the or51133 firmware loading function that
has no effect.  Left a comment to in case it helps someone trying
to reverse engineer the chip.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NAndrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This reverts commit 786dc1d3.

As Al so eloquently points out, the patch is crap. The old code was fine,
the new code was bogus.

It never dereferenced a user pointer, the "->" operator was to an array
member, which gives the _address_ of the member (in user space), not an
actual dereference at all.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is the minimal resume trace code to find which device resume (if
any) results in problems.  Usually, you'd use the information this
generates as a starting point to adding more fine-grained trace event
points.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Considering that there isn't a lot of hw we can depend on during resume,
this is about as good as it gets.

This is x86-only for now, although the basic concept (and most of the
code) will certainly work on almost any platform.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Patch from Ben Dooks

Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

From: Tilman (DRM CVS)
Signed-off-by: NDave Airlie <airlied@linux.ie>

i915 vblanks can be generated from either pipe a or b, however a disabled
pipe generates no interrupts. This change allows the X server to select
which pipe generates vblank interrupts.

From: Keith Packard <keith.packard@intel.com> via DRM CVS
Signed-off-by: NDave Airlie <airlied@linux.ie>

Add support for r200 vertex programs (R200_EMIT_VAP_PVS_CNTL, and new
packet type for making it possible to address whole tcl vector space
and have a larger count)

From: Roland Scheidegger (DRM CVS)
Signed-off-by: NDave Airlie <airlied@linux.ie>

Do a tcl state flush before accessing tcl vector space. This fixes some
more problems with flickering (bug #6637). drm may not be appropriate
place for this, since doing that flush there might both be overkill and
insufficient in some cases. However, it's hard to figure out when that
flush is needed, so this has to suffice. There does not seem to be a
performance penalty associated with it.

From: Roland Scheidegger (DRM CVS)
Signed-off-by: NDave Airlie <airlied@linux.ie>

ring_head is offset in card memory, not iomem pointer.  Fixed, removed
fuckloads of amazingly bogus casts somebody had sprinkled all over the
place.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not try to kfree(esp), scsi_host_put() takes care of that.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

And make it a real PCI driver too.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use CONFIG_SPARC and CONFIG_SPARC64 instead.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This also turns the driver into a new-style scsi driver.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I severely apologize, I was still learning how to program
in C when I wrote this stuff 10 years ago...
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sparcspkr and power drivers are converted, to make sure it works.
Eventually the SBUS device layer will use this as a sub-class.

I really cannot cut loose on that bit until sparc32 is given the
same infrastructure.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One thing this change pointed out was that we really should
pull the "get 'local-mac-address' property" logic into a helper
function all the network drivers can call.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In particular, move the IRQ probing out to sparc32/sparc64
arch specific code where it belongs.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent possible null dereference due to misplaced ;
Signed-off-by: NDave Jones <davej@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/cpufreq/cpufreq_ondemand.c: In function 'do_dbs_timer':
drivers/cpufreq/cpufreq_ondemand.c:374: warning: implicit declaration of function 'lock_cpu_hotplug'
drivers/cpufreq/cpufreq_ondemand.c:381: warning: implicit declaration of function 'unlock_cpu_hotplug'
drivers/cpufreq/cpufreq_conservative.c: In function 'do_dbs_timer':
drivers/cpufreq/cpufreq_conservative.c:425: warning: implicit declaration of function 'lock_cpu_hotplug'
drivers/cpufreq/cpufreq_conservative.c:432: warning: implicit declaration of function 'unlock_cpu_hotplug'

Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The IDE power management can just use the ->end_io_data member to store
it's data.
Signed-off-by: NJens Axboe <axboe@suse.de>

A process flag to indicate whether we are doing sync io is incredibly
ugly. It also causes performance problems when one does a lot of async
io and then proceeds to sync it. Part of the io will go out as async,
and the other part as sync. This causes a disconnect between the
previously submitted io and the synced io. For io schedulers such as CFQ,
this will cause us lost merges and suboptimal behaviour in scheduling.

Remove PF_SYNCWRITE completely from the fsync/msync paths, and let
the O_DIRECT path just directly indicate that the writes are sync
by using WRITE_SYNC instead.
Signed-off-by: NJens Axboe <axboe@suse.de>

While writing a version of losetup, I ran into the problem that the loop
device was returning total garbage.

It turns out the problem was that this losetup was only issuing the
LOOP_SET_FD ioctl and not issuing a subsequent LOOP_SET_STATUS ioctl.  This
losetup didn't have any special status to set, so it left out the call.

The deeper cause is that loop_set_fd sets the transfer function to NULL,
which causes no transfer to happen lo_do_transfer.

This patch fixes the problem by setting transfer to transfer_none in
loop_set_fd.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: N"Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Mark a few non-exported functions static.
Signed-off-by: NPeter Hagervall <hager@cs.umu.se>
Cc: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>