Newer generation chips require the firmware be notified before we
start the IQK calibration.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The firmware command API differs slightly between new and old
devices. The new generation requires the size since there is no
extension bit encoded into the command number.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Likewise for 8723bu, use a pointer to the efuse.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make the code easier to read and less error prone by using a pointer
to the efuse.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NJakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NJakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Avoid a negative conditional and an extra level of indentation in the
bigger part of the loop body.
Signed-off-by: NJakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It is enough to check for either illegal offset or illegal map address
because map address is a value derived from an offset:

  map_addr = offset * 8
  EFUSE_MAP_LEN = EFUSE_MAX_SECTION_8723A * 8

Leave just the check for an illegal map address because its upper
bound (EFUSE_MAP_LEN) is used also in a couple other places.
Signed-off-by: NJakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The larger mailboxes also use a different set of mailbox commands.
This provides a list of the 64 bit commands.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In addition do not apply fixups for 8188/8191/8192 A-cut UMC parts.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This introduces additional register definitions for newer generation
chips.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Gen1 chips use a 16 bit mailbox extension register, for upto 48 bit
mailbox commands. The newer generation chips use a 32 bit mailbox
extension register instead, for upto 64 bit mailbox commands.

Handle writing the larger mailboxes.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The different RF module seems to require a different AGC table as well
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer chips seem to have some different mac registers, requiring
a different init table.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far this is just for 8723BU. It includes writing to a number of
registers I have seen no description for so far.

0x0064
0x0930
0x0944
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add 8723bu 1T radio init table. The vendor driver indicates that some
registers need special treatment for TFBGA90, TFBGA80, and TFBGA79
packaging. However the vendor driver never actually checks the package
type, so just stick to default values here.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This adds the 8723bu PHY 1T init table.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Only 1st generation chips do provide USB interrupts, so do not try to
setup interrupts for newer chips (8192eu and 8723bu).
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8723bu, like the 8192eu, can also handle 1024 byte block writes.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement first stab at parsing the 8723bu's efuse.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This provides initial detection of 8723bu devices, and selects the
correct firmware image to load.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The newer generation chips have different interrupt registers.
Initialize this correct registers on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu (and some other parts) will report an incorrect USB OUT
EP. This tells the chip to drop it - as per the vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The logic for testing auto load failure in rtl8xxxu_auto_llt_table()
was inverted.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To match the flow of the vendor driver, move the LLT init to after the
firmware is started.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This reorganizes the device initialization to init page boundaries
before starting the firmware. This matches the flow in the 8192eu
vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer chips can auto load the LLT table, it is no longer necessary to
build it manually in the driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This implements the rtl8192eu power on sequence, and splits it off
from the rtl8192cu/rtl8723au power on sequence.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The rtl8192eu can handle 1024 byte block writes, unlike it's
predecessors (8192cu/8188cu).
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This identifies the chip vendors correctly and also picks the correct
firmware for rtl8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is the start of 8192eu support. For now just detect the device
and parse the efuse.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Smatch reports the following warning:

  CHECK   drivers/net/wireless/realtek/rtlwifi/rc.c
drivers/net/wireless/realtek/rtlwifi/rc.c:144 _rtl_rc_rate_set_series() warn: impossible condition '(wireless_mode == 256) => (0-255 == 256)'

This warning arises because commit acc6907b87a9 ("rtlwifi: Fix warning
from ieee80211_get_tx_rates() when using 5G") now checks the wireless
mode for WIRELESS_MODE_AC_ONLY (BIT(8)) in _rtl_rc_rate_set_series().
As a result, all quantities used to store the wireless mode must be u16.

This patch also reorders struct rtl_sta_info to save a little space.

Fixes: d76d65fd ("rtlwifi: fix broken VHT support")
Reported-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

passing rtl_stats by value is inefficient; the structure is over 300
bytes in size and generally just one field (packet_report_type)
is being accessed, so the pass by value is a relatively large overhead.
This change just affects just the rx_command_packet calls.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Routine rtl_addr_delay() uses delay statements in code that can
sleep. To improve system responsiveness, the various delay statements
are changed.

In addition, routines rtl_rfreg_delay() and rtl_bb_delay() are
rewritten to use the code in rtl_addr_delay() for most of their
input values.
Suggested-by: NByeoungwook Kim <quddnr145@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When driver rtl8821ae is loaded but not connected to any AP, it logs
a "firmware not ready to run" message roughly once a minute. To
eliminate logging this massage under normal debug conditions, the
degug level needed to print this message is increased.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There are several copies of the 5G channel tables in this driver. These
are removed so that the tables in the core will be used. This change
also removes a useless message of "Channel 163 in Group not found".

The number of possible 5G channels was reduced from 54 to a better
value of 49 during the conversion.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The driver defines its own set of channel tables for the 5G band. With
this change, it will use those of the core.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This driver defines its owh copy of the 5G channels. Change it to use
the common definitions.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There are 3 drivers in this family that have 5G radios. Each of them
defines local copies of the available channels. This patch adds the
two arrays to the core driver.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>