Ryan noticed that on his board, HDMI was wired up to port C but not
exposed by the kernel, which had only expected DP on that port.  Fix
that up by enumerating both ports if possible.
Tested-by: N"Matsumura, Ryan" <ryan.matsumura@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fix up the whitespace fail. Tsk.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Caught by the dead code police!
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

And also fix a small typo in the intel_encoder_dpms() comment.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rather than open-code the teardown of a framebuffer, export the routine
from intel_display.c. This then make intel_fbdev symmetric in its use of
the common intel_framebuffer routines to initialise and clean up the
struct intel_framebuffer. (And new features need only be added in one
location!)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Userspace can pass a mode with an unspecified vsync/hsync polarity
setting. All encoders in the Intel driver take this to mean a negative
polarity setting. The HW readout/state checker code on the other hand
needs these flags to be explicitly set, otherwise the state checker will
WARN about the mismatch.

Get rid of the WARN by making the polarity setting explicit in the
adjusted mode flags based on the requested mode flags. This will keep
the existing behavior otherwise.

Note that we could guess from the other timing parameters whether the
user wanted a VESA or other standard mode and set the polarity
accordingly. This is what the NV driver does
(drivers/gpu/drm/nouveau/dispnv04/crtc.c), but I think that's not very
exact and would change the existing behavior of the Intel driver.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65442Signed-off-by: NImre Deak <imre.deak@intel.com>
Tested-by: Ncancan,feng <cancan.feng@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

VLV wants encoder enabling before the pipe is up. With the previously
rearranged VLV DP and HDMI ->pre_enable and ->enable callbacks in place,
this no longer depends on the early ->enable hook call. Move the
->enable call at the end of the sequence, similar to the crtc enable on
other platforms. This will be needed e.g. for moving the eDP backlight
enabling to the right place in the sequence, currently done too early on
VLV.

There should be no functional changes.

v2: Rebase.

v3: Explain why this is needed in the commit message (Chris).
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise we get flooded by the kernel warning us that we are doing
long sequences of IO without serialisation. For example,

 WARNING: CPU: 0 PID: 11136 at drivers/gpu/drm/i915/intel_sideband.c:40 vlv_sideband_rw+0x48/0x1ef()
 Modules linked in:
 CPU: 0 PID: 11136 Comm: kworker/u2:0 Tainted: G        W    3.11.0-rc2+ #4
 Call Trace:
  [<c2028564>] ?  warn_slowpath_common+0x63/0x78
  [<c227ad43>] ?  vlv_sideband_rw+0x48/0x1ef
  [<c20285dd>] ?  warn_slowpath_null+0xf/0x13
  [<c227ad43>] ?  vlv_sideband_rw+0x48/0x1ef
  [<c227b060>] ?  vlv_dpio_write+0x1c/0x21
  [<c2262b3b>] ?  intel_dp_set_signal_levels+0x24a/0x385
  [<c2264909>] ?  intel_dp_complete_link_train+0x25/0x1d1
  [<c2264c55>] ?  intel_dp_check_link_status+0xf7/0x106
  [<c2238ced>] ?  i915_hotplug_work_func+0x17b/0x221
  [<c203a204>] ?  process_one_work+0x12e/0x210
  [<c203a5e4>] ?  worker_thread+0x116/0x1ad
  [<c203a4ce>] ?  rescuer_thread+0x1cb/0x1cb
  [<c203d8f5>] ?  kthread+0x67/0x6c
  [<c2457ebb>] ?  ret_from_kernel_thread+0x1b/0x30
  [<c203d88e>] ?  init_completion+0x18/0x18

v2: Retire the locking in vlv_crtc_enable() and do it close to the meat.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
[danvet: Squash in a s/mutex_lock/mutex_unlock/ fixup spotted by the 0
day kernel build/coccinelle and reported by Dan Carpenter.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Art confirms that this should work fine.  Since most panels are 18bpp
with dithering from 24bpp, the existing code wouldn't be enabled in most
cases.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NStéphane Marchesin <marcheu@chromium.org>
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the old days of the crtc helpers we've only had the encoder and
crtc ->mode_fixup callbacks. So when the lvds connector wanted to
adjust the crtc timings it had to set a driver-private mode flag to
tell the crtc mode fixup code to not overwrite them with the generic
ones.

When converting things to the new infrastructure I've kept the entire
logic and only moved the flag to pipe_config->timings_set. But this
logic is pretty tricky and already caused regressions:

commit 21d8a475
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Fri Jul 12 08:07:30 2013 +0200

    drm/i915: fix pfit regression for non-autoscaled resolutions

So take advantage of the flexibility our own modeset infrastructure
affords us and prefill default crtc timings. This allows us to rip out
->timings_set. Note that we overwrite things again when retrying the
pipe config computation due to bandwidth constraints to avoid bogus
crtc timings if the encoder only does relative adjustments (which is
how the pfit code works). Only a theoretical concern though since
platforms where we retry (pch-split platforms) do not need
adjustements (since only the old gmch pfit needs that). But let's
better be safe than sorry.

Since we now initialize the crtc timings before calling the
encoder->compute_config functions the crtc initialization in the gmch
pfit code is now redudant and so can be removed.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add a paragraph to the commit message to explain why we can
ditch the crtc timings initialization call from the gmch pfit code, to
answer a question from Rodrigo's review.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The encoder->mode_set callback from the crtc helpers is now completely
unused in our driver. Good riddance!
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Everyone is now using our own ->compute_config callback, which means
we can now also make that callback mandatory.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need the correct clock to accurately assess whether we need to
enable the double wide pipe mode or not.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Stuart Abercrombie <sabercrombie@google.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently, the register access code is split between i915_drv.c and
intel_pm.c. It only bares a superficial resemblance to the reset of the
powermanagement code, so move it all into its own file. This is to ease
further patches to enforce serialised register access.

v2: Scan for random abuse of I915_WRITE_NOTRACE
v3: Take the opportunity to rename the GT functions as uncore. Uncore is
the term used by the hardware design (and bspec) for all functions
outside of the GPU (and CPU) cores in what is also known as the System
Agent.
v4: Rebase onto SNB rc6 fixes
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Wrestle patch into applying and inline
intel_uncore_early_sanitize (plus move the old comment to the new
function). Also keep the _santize postfix for intel_uncore_sanitize.]
[danvet: Squash in fixup spotted by Chris on irc: We need to call
intel_pm_init before intel_uncore_sanitize since the later will call
cancel_work on the delayed rps setup work the former initializes.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For now there are no callers, but these functions are going to be
needed for the code that allows Package C8+. Other future features may
also require this code.

Also merge the commit which introduced assert_can_disable_lcpll and
had the following commit message:

Most of the hardware needs to be disabled before LCPLL is disabled, so
let's add a function to assert some of items listed in the "Display
Sequences for LCPLL disabling" documentation.

The idea is that hsw_disable_lcpll should not disable the hardware,
the callers need to take care of calling hsw_disable_lcpll only once
everything is already disabled.

v2: - Rebase.
    - Fix D_COMP wait timeout.
v3: - Use wait_for_atomic_use (Ben)
    - Remove/add a useless/needed POSTING_READ (Ben)
    - Early return in case LCPLL is already restored (Ben)
    - Add ndelay(100) (Ben)
v4: - Merge the commit that added assert_can_disable_lcpll (Ben)
    - Add interrupt assertions (Ben)
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix compile fail since there's no HAS_LP_PCH yet.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We currently don't support HDMI clock bending nor use SSC for DP or
HDMI on Haswell, so the only case where we need CLKOUT_DP is for VGA.

v2: - Replace the IS_ULT check for LPT-LP
    - Simplify GEN0/DBUFF0 check due to change on the previous patch
    - Also check for SBI_SSCCTL_DISABLE (Ben).
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now it implements 3 different sequences from BSpec and also has
support for ULT.

v2: - Change IS_ULT checks for LPT-LP checks
    - Add check for LPT-LP + with_fdi (Ben)
    - Merge DBUFF0/GEN0 bit definitions since they're the same
      register (Ben)
    - DBUFF0 (1<<0) is Disable, not Enable
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=47941
BugLink: https://bugs.launchpad.net/bugs/1163720
BugLink: https://bugs.launchpad.net/bugs/1162026

Some machines suffer from non-functional backlight controls if
BLM_PCH_PWM_ENABLE is set, so provide a quirk to avoid doing so.
Apply this quirk to Dell XPS 13 models.
Tested-by: NEric Griffith <EGriffith92@gmail.com>
Tested-by: NKent Baxley <kent.baxley@canonical.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: NKamal Mostafa <kamal@canonical.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The next step is to modify lpt_enable_clkout_dp to enable support for
"Sequence to enable CLKOUT_DP" and "Sequence to enable CLKOUT_DP
without spread".
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Because lpt_init_pch_refclk implements the "Sequence to enable
CLKOUT_DP for FDI usage and configure PCH FDI I/O", which is very
similar to "Sequence to enable CLKOUT_DP" and "Sequence to enable
CLKOUT_DP without spread". With the extracted functions we can more
easily implement the two missing sequences.

v2: Rebase (WaMPhyProgramming:hsw comment).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The machines that fall in the "is_sdv" case are some very early
pre-production steppings. This patch may break VGA output after
suspend/resume on these machines.

Even the documentation for the is_sdv cases was removed from BSpec.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

PSR must be enabled after transcoder and port are running.
And it is only available for HSW.

v2: move enable/disable to intel_ddi
v3: The spec suggests PSR should be disabled even before backlight (by pzanoni)
v4: also disabling and enabling whenever panel is disabled/enabled.
v5: make it last patch to avoid breaking whenever bisecting. So calling for
    update and force exit came to this patch along with enable/disable calls.
v6: Remove unused and unecessary psr_enable/disable calls, as notice by Paulo.

CC: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Drop the psr exit code in the busy ioctl since I didn't merge
that part of the infrastructure yet - it needs more thought.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In commit e3de42b6
Author: Imre Deak <imre.deak@intel.com>
Date:   Fri May 3 19:44:07 2013 +0200

    drm/i915: force full modeset if the connector is in DPMS OFF mode

a new function was added that walked over the set of connectors to see
if any of the currently associated CRTC was switched off. This function
walked an array of connectors, rather than the array of pointers to
connectors contained in the drm_mode_set - i.e. it was dereferencing far
past the end of the first connector. This only becomes an issue if we
attempt to use a clone mode (i.e. more than one connector per CRTC) such
that set->num_connectors > 1.
Reported-by: NTimo Aaltonen <tjaalton@ubuntu.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65927Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Egbert Eich <eich@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There seems to be no limit to the amount of gunk the firmware can
leave behind. Some platforms leave pch dplls on which are not in
active use at all. The example in the bug report is a Apple Macbook
Pro.

Note that this escape scrunity of the hw state checker until we've
tried to use this enabled, but unused pll since we did only check for
the inverse case of a in-used, but disabled pll.

v2: Add a WARN in the pll state checker which would have caught this
case.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66952Reported-and-tested-by: Nshui yangwei <yangweix.shui@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Toghether with the hw state readout this should catch cases where we
don't properly updated the pll state (either in sw or hw). At least
for the shared dpll code the equivalent tricke helped a lot in
catching bugs.

Also rename the function prefix, it's not a generic piece of
infrastructure.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bspec for the "DPLL HDMI multiplier" field says:

"Restriction : The DPLL must be enabled and stable before setting these bits.
These bits must be programmed after DPLL_SEL is programmed."

There is apparently no restriction on programming the DPLL_SEL
register wrt the DPLL. So let's just move that up before we enable the
pch dpll.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

No need to call the ->pre_pll_enable hook twice if we don't enable the
dpll too early. This should make Jani a bit less grumpy.

v2: Rebase on top of the newly-colored BUG_ONs.

v3: Reinstate the lost write of the DPLL_MD register, spotted by Imre.

Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move error state generation and stringification to it's
own compilation unit. Sysfs also uses this so it can't be
under CONFIG_DEBUG_FS

This fixes a regression introduced in

commit ef86ddce
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date:   Thu Jun 6 17:38:54 2013 +0300

    drm/i915: add error_state sysfs entry

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66814Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Came accross two open coding of for_each_pipe(), might as well use the
macro.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's in the PFIT_CONTROL register, but very much associated with the
lvds encoder. So move the readout for it (in the case of an otherwise
disabled pfit) from the pipe to the lvds encoder's get_config
function.

Otherwise we get a pipe state mismatch if we use pipe B for a non-lvds
output and we've left the dither bit enabled behind us. This can
happen if the BIOS has set the bit (some seem to unconditionally do
that, even in the complete absence of an lvds port), but not enabled
pipe B at boot-up. Then we won't clear the pfit control register since
we can only touch that if the pfit is associated with our pipe in the
crtc configuration - we could trample over the pfit state of the other
pipe otherwise since it's shared. Once pipe B is enabled we notice
that the 6to8 dither bit is set and complain about the mismatch.

Note that testing indicates that we don't actually need to set this
bit when the pfit is disabled, dithering on 18bpp panels seems to work
regardless. But ripping that code out is not something for a bugfix
meant for -rc kernels.

v2: While at it clarify the logic in i9xx_get_pfit_config, spurred by
comments from Chris on irc.

v3: Use Chris suggestion to make the control flow in
i9xx_get_pfit_config easier to understand.

v4: Kill the extra line, spotted by Chris.
Reported-by: NKnut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: http://lists.freedesktop.org/archives/intel-gfx/2013-July/030092.htmlTested-by: NKnut Petersen <Knut_Petersen@t-online.de>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I just got confirmation that we're using some old values for the PLL
LPF coefficients for DP RBR/HDMI/DAC on VLV. The
VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9 document lists both values
by mistake, and apparently we had picked the wrong one. Change the
coefficients to the recommended values.

Changing the value doesn't appear to destabilize the VGA output picture
even with my sensitive HP ZR24w display. Also HDMI output to my TV still
works fine.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Section 1.5.4, "DPLL A Control Register" from Bspec about bit 23
"FPA0/A1 P2 Clock Divide":

0 = Divide by 2
1 = Divide by 4. This bit must be set in DVO non-gang mode

So copy the current limits (which should be good for i8xx) and create
a new set for dvo encoders.
Reviewed-by: NChris Wilson <chris@chris-wilson.oc.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I've missed that intel_dvo_mode_set changes the dpll configuration.
Hence when I've reworked the sequence to only enable the dpll in the
crtc_enable callback in

commit 66e3d5c0
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sun Jun 16 21:24:16 2013 +0200

    drm/i915: move i9xx dpll enabling into crtc enable function

that special DVO bit was lost. Some BSpec reading confirms that it's
only needed for DVO encoders. Section 1.5.4, "DPLL A Control Register"
for bit 30:

"2X Clock Enable. When driving In non-gang DVO modes such as a
connected flat panel or TV, a 2X" version of the clock is needed. When
not using the 2X output it should be disabled. This bit cannot be set
when driving the integrated LVDS port on devices such as Montara-GM."

Fix this regression up.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66516
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Partially-tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Soon we want to gut a lot of our existing assumptions how many address
spaces an object can live in, and in doing so, embed the drm_mm_node in
the object (and later the VMA).

It's possible in the future we'll want to add more getter/setter
methods, but for now this is enough to enable the VMAs.

v2: Reworked commit message (Ben)
Added comments to the main functions (Ben)
sed -i "s/i915_gem_obj_set_color/i915_gem_obj_ggtt_set_color/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_bound/i915_gem_obj_ggtt_bound/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_size/i915_gem_obj_ggtt_size/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_offset/i915_gem_obj_ggtt_offset/" drivers/gpu/drm/i915/*.[ch]
(Daniel)

v3: Rebased on new reserve_node patch
Changed DRM_DEBUG_KMS to actually work (will need fixing later)
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We only do this on IBX where there's a fixed pch dpll to pipe
assignment. Being explicit about it can't really hurt and makes
sparse happy.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This makes sparse happy and also makes it a bit more obvious where we
pull off this trick - after all we're only allowed to do it eithe as a
default or on platforms where there is no disdinction between the pipe
and the cpu transcoder.
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should help on HSW, where we don't currently have a get_clock call.
Reported-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Print out the flag that failed and fix up a mismatched paren.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>