Rather than having the user half start a stream but avoid any DMA to
trigger data flow on links which don't pass through the CPU create a
DAPM route between the two DAI widgets using a hw_params configuration
provided by the machine driver with the new 'params' member of the
dai_link struct.  If no configuration is provided in the dai_link then
use the old style even for CODEC<->CODEC links to avoid breaking
systems.

This greatly simplifies the userspace usage of such links, making them
as simple as analogue connections with the stream configuration being
completely transparent to them.

This is achieved by defining a new dai_link widget type which is created
when CODECs are linked and triggering the configuration of the link via
the normal PCM operations from there.  It is expected that the bias
level callbacks will be used for clock configuration.

Currently only the DAI format, rate and channel count can be configured
and currently the only DAI operations which can be called are hw_params
and digital_mute().  This corresponds well to the majority of CODEC
drivers which only use other callbacks for constraint setting but there
is obviously much room for extension here.  We can't simply call
hw_params() on startup as things like the system clocking configuration
may change at runtime and in future it will be desirable to offer some
configurability of the link parameters.

At present we are also restricted to a single DAPM link for the entire
DAI.  Once we have better support for channel mapping it would also be
desirable to extend this feature so that we can propagate per-channel
power state over the link.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

We should always have a CODEC already there when registering a CODEC DAI
and for CODEC<->CODEC links a dai_link will have two CODECs so it's much
simpler to do things at registration time.

This results in a slight change in the error handling for failed CODEC
DAI registrations but practically speaking these are never supposed to
fail so there shouldn't be much issue. The change is that we don't fail
the overall CODEC registration if the DAI registration fails; this seems
more robust anyway as we may not need to use a given DAI in a particular
system.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When two CODEC DAIs are linked directly to each other then if we give the
same master mode settings to both devices things won't work as either
neither will drive or they'll drive against each other. Flip the settings
for the DAI in the CPU slot of the DAI link.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This helps us ignore errors in callers if the operation failed due to not
being available as opposed to an error.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op.  This leads to a
proliferation of the default_open() implementation across the entire
tree.

Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().

This replacement was done with the following semantic patch:

<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}

@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sound/soc/soc-core.c: In function ‘snd_soc_put_volsw_sx’:
sound/soc/soc-core.c:2600: warning: ‘err’ may be used uninitialized in this function
Signed-off-by: NBrian Austin <brian.austin@cirrus.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Some codecs namely Cirrus Logic Codecs have a way of wrapping the dB scale around 0dB without 0dB being in the middle.

Rework of SOC_DOUBLE_R_SX_TLV to be more consistent with other asoc tlv macros.
Add single register macro : SOC_SINGLE_SX_TLV.
Use snd_soc_info_volsw for .info
Use snd_soc_get_volsw_sx, snd_soc_put_volsw_sx for single and double.

kcontrols for CS42L51 and CS42L73 are adjusted to these new TLV Macros.

The max value is determined by: (number of steps) +1 for 0dB +max from codec datasheet.
Signed-off-by: NBrian Austin <brian.austin@cirrus.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In version 3.4 the driver core acquired probe deferral which is a core way
of doing essentially the same thing as ASoC has been doing since forever
to make sure that all the devices needed to make up the card are present
without needing open coding in the subsystem.

Make basic use of this probe deferral mechanism for the cards, removing the
need to handle partially instantiated cards. We should be able to remove
even more code than this, though some of the checks we're currently doing
should stay since they're about things like suppressing unneeded DAPM runs
rather than deferring probes.

In order to avoid robustness issues with our teardown paths (which do need
quite a bit of TLC) add a check for aux_devs prior to attempting to set
things up, this means that we've got a reasonable idea that everything will
be there before we start. As with the removal of partial instantiation
support more work will be needed to make this work neatly.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Currently stream events are only perfomed on codec stream widgets only.
There is now a need to be able to perform stream events on platform
widgets too.

e.g. we have the ABE platform driver with several DAI links
to dummy codecs. We need to be able to perform stream events on any
of the dummy codec DAI links.

This patch also removes the snd_soc_dai * parameter since it's already
contained within the rtd * parameter.

Finally makle stream event return void since no one checks it anyway.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add platform driver support for CPU DAI DAPM widgets.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It has now become necessary to use a DAPM mutex instead of the codec
mutex to lock the DAPM operations. This is due to the recent multi
component support and forth coming Dynamic PCM updates.

Currently we lock DAPM operations with the codec mutex of the calling
RTD context. However, DAPM operations can span the whole card context
and all components.

This patch updates the DAPM operations that use the codec mutex to
now use the DAPM mutex PCM subclass for all DAPM ops.

We also add a mutex subclass for DAPM init and PCM operations.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is the first part of a change that is intended to improve
ASoC locking protection for DAPM and PCM operations.

This part of the series adds a mutex class for the soc_card mutex. The
SND_SOC_CARD_CLASS_INIT class is used for card initialisation only whilst the
SND_SOC_CARD_CLASS_PCM class is used for the forth coming Dynamic
PCM operations. The new mutex classes are required otherwise we will see a false
positive mutex deadlock warning between the card initialisation and the PCM
operations (something that would never deadlock in real life).
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We're currently not freeing card->rtd in cases where the card is
unregistered before being instantiated - convert it to devm_kzalloc() to
make sure that happens.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Not having a DAI link set_fmt operation is perfectly normal and
should not be complaint.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add mutex support for platform IO operations. e.g. can be used
for platform DAPM widget IO ops.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

snd_soc_register_card() has been available and strongly preferred since
2.6.38 but we're still seeing new drivers using it and the conversion rate
for older machines has been low. Help address both issues by logging a
warning when the soc-audio device probes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Make sure we cleanup the platform debugfs when probe fails.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

SET_SYSTEM_SLEEP_PM_OPS writes .poweroff = *_resume once. Then we overwrite it
again explicitly as .poweroff = snd_soc_poweroff. Even though it works, as the
second one overwrites the first one, this is not the correct way. Fix this by
expanding SET_SYSTEM_SLEEP_PM_OPS in our structure.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Chip designers frequently include things like the enable and disable
controls for algorithms in the register blocks which also hold the
coefficients. Since it's desirable to split out the enable/disable
control from userspace the plain SND_SOC_BYTES() isn't optimal for
these devices.

Add a SND_SOC_BYTES_MASK() which allows a bitmask from the first word
of the block to be excluded from the control. This supports the needs
of devices I've looked at and lets us have a reasonably simple API.
Further controls can be added in future if that's needed.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Allow devices to export blocks of registers to the application layer,
intended for use for reading and writing coefficient data which can't
usefully be worked with by the kernel at runtime (for example, due to
requiring complex and expensive calculations or being the results of
callibration procedures). Currently drivers are using platform data to
provide configurations for coefficient blocks which isn't at all
convenient for runtime management or configuration development.

Currently only devices using regmap are supported, an error will be
generated for any attempt to work with a byte control on a non-regmap
device. There's no fundamental block to other devices so support could
be added if required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Showing the returned values on error messages is useful information.

While at it, use pr_err/pr_warn whenever possible.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In order to allow us to do smarter things with DAI links create DAPM
widgets which directly represent the DAIs in the DAPM graph. These are
automatically created from the DAIs as we probe the card with references
held in both directions between the widget and the DAI.

The widgets are not made available for direct instantiation by drivers,
they are created automatically from the DAIs.  Drivers should be updated
to create stream routes using DAPM maps rather than by annotating AIF
and DAC widgets with streams.

In order to ease transition to this model from existing drivers we
automatically create DAPM routes between the DAI widgets and the existing
stream widgets which are started and stopped by the DAI widgets, though
the old stream handling mechanism is still in place.  This also has the
nice effect of removing non-DAPM devices as any device with a DAI
acquires a widget automatically which will allow future simplifications
to the core DAPM logic.

The intention is that in future the AIF and DAI widgets will gain the
ability to interact such that we are able to manage activity on
individual channels independantly rather than powering up and down the
entire AIF as we do currently.

Currently we only generate these for CODECs, mostly as I have no systems
with non-CODEC DAPM to integrate with. It should be a simple matter of
programming to add the additional hookup for these.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Neater and avoids warnings when used in other places where const strings
are desired.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

In order to allow us to do something smarter than iterate through widgets
doing strcmp() to work out what to power up for stream events change the
interface used to generate them to be based on the combination of a DAI
and a stream direction rather than just a simple string identifying the
stream.

At some point we'll probably want a set of channels too.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Allow platform widgets to be visible in debugfs like codec widgets.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Update the codec debugfs initialisation to use dev_warn() instead of
printk(KERN_WARNING).
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is usually not a use case dependant flag anyway.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.

This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-

snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()

This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().

It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().

Finally, it updates the existing machine drivers that register controls to either :-

1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.

In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Use the same pm_ops for all system suspend and resume paths. This isn't
ideal for suspend to disk with older CODECs as we'll suspend and then
resume the CODEC before powering off all of which takes a long time due
to VMID ramps but it's very simple to implement and for modern CODECs the
overhead should be minimal.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

If an idle_bias_off device is in any state other than off then it is still
active for some reason (typically a low power function such as accessory
detection). This wasn't an issue when the feature was implemented as we
always went to _ON for any active function, subsequent power improvements
have changed things.

With the modern way of doing things we should overhaul the infrastructure
to allow devices to explicitly take references for these functions but
that's a much more invasive change and will require driver updates to
deploy, this will bring the framework into line with the existing driver
set before we do that work.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Print out the offending DAI link entry when a naming error occurs. Makes
thing easier to debug for machines with a large number of DAI links.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Fix platform removal by freeing the platform DAPM resources and remove
it from the DAPM list.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The device model needs a release() function so it can free devices when
they become dereferenced.  Do that for rtds.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure that everything is seeing the same declaration by moving it to
a header file rather than putting the declaration in soc-core.c
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

DAI link endpoints and platform (DMA) devices are currently specified
by name. When instantiating sound cards from device tree, it may be more
convenient to refer to these devices by phandle in the device tree, and
for code to describe DAI links using the "struct device_node *"
("of_node") those phandles map to.

This change adds new fields to snd_soc_dai_link which can "name" devices
using of_node, enhances soc_bind_dai_link() to allow binding based on
of_node, and enhances snd_soc_register_card() to ensure that illegal
combinations of name and of_node are not used.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Implement snd_soc_of_parse_audio_routing(), a utility function that can
parses a simple DAPM route table from device tree.The machine driver
specifies the DT property to use, since this is binding-specific.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Implement snd_soc_of_parse_card_name(), a utility function that sets a
card's name from device tree. The machine driver specifies the DT
property to use, since this is binding-specific.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The message was obviously copied from soc_init_codec_debugfs()
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Transform some loops from:

for_each(x) {
    if (f(x)) {
        work_on(x);
    }
}

to new structure:

for_each(x) {
    if (!f(x))
        continue;

    work_on(x);
}

This will allow future modification of f(x) with less impact to the code.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>