If an error happens in the tx completion thread, tg3_reset_task will be
scheduled and TX_RECOVERY_PENDING will be set.  The TX_RECOVERY_PENDING
flag causes tg3_poll[_msix] to return early before doing much of its
work.  Tg3_reset_task() gets canceled when the configuration of the
device is changing, which always results in a chip reset.  When this
happens, the TX_RECOVERY_PENDING flag may be left set, which would
unnecessarily hinder tg3_poll from doing work.  This patch fixes the
problem.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tg3_phy_copper_begin() has code that configures the link
advertisements through the use of the link_config.speed and
link_config.duplex members.  The driver does not internally use these
members in this way, nor is it (currently) permitted via the ethtool
interface.  This patch removes the dead code.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3 driver tried to detect link changes by comparing the tg3 local
active_speed member with SPEED_UNKNOWN (or formerly SPEED_INVALID).
This check is not correct, since phylib will never set its speed member
to either of these two values.  The code only appeared to work because
tg3 initializes active_speed to SPEED_INVALID during tg3_init_one.  This
patch introduces a new "old_link" tg3 member and then compares the
phy_device's link member against it to detect link state changes.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Piergiorgio Beruto expressed the need to fetch size of first datagram in
queue for AF_UNIX sockets and suggested a patch against SIOCINQ ioctl.

I suggested instead to implement MSG_TRUNC support as a recv() input
flag, as already done for RAW, UDP & NETLINK sockets.

len = recv(fd, &byte, 1, MSG_PEEK | MSG_TRUNC);

MSG_TRUNC asks recv() to return the real length of the packet, even when
is was longer than the passed buffer.

There is risk that a userland application used MSG_TRUNC by accident
(since it had no effect on af_unix sockets) and this might break after
this patch.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Tested-by: NPiergiorgio Beruto <piergiorgio.beruto@gmail.com>
CC: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_mac_addr() for .ndo_set_mac_address, remove
lowpan_set_address since it do currently the same as
eth_mac_addr(). Additional advantage: eth_mac_addr() already
checks if the given address is valid
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Acked-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_mac_addr() for .ndo_set_mac_address, remove
typhoon_set_mac_address() since it do currently the same as
eth_mac_addr(). Additional advantage: eth_mac_addr() already
checks if the given address is valid.
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Acked-by: NDave Dillow <dave@thedillows.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver is the last user of the IRQF_SAMPLE_RANDOM flag for net drivers, and since add_*_randomness
interfaces have now deprecated the flag as a source of external noise, we can remove it.
Signed-off-by: NDavidlohr Bueso <dave@gnu.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

The same here -- we can protect the sk_peek_off manipulations with
the unix_sk->readlock mutex.

The peeking of data from a stream socket is done in the datagram style,
i.e. even if there's enough room for more data in the user buffer, only
the head skb's data is copied in there. This feature is preserved when
peeking data from a given offset -- the data is read till the nearest
skb's boundary.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sk_peek_off manipulations are protected with the unix_sk->readlock mutex.
This mutex is enough since all we need is to syncronize setting the offset
vs reading the queue head. The latter is fully covered with the mentioned lock.

The recently added __skb_recv_datagram's offset is used to pick the skb to
read the data from.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This one specifies where to start MSG_PEEK-ing queue data from. When
set to negative value means that MSG_PEEK works as ususally -- peeks
from the head of the queue always.

When some bytes are peeked from queue and the peeking offset is non
negative it is moved forward so that the next peek will return next
portion of data.

When non-peeking recvmsg occurs and the peeking offset is non negative
is is moved backward so that the next peek will still peek the proper
data (i.e. the one that would have been picked if there were no non
peeking recv in between).

The offset is set using per-proto opteration to let the protocol handle
the locking issues and to check whether the peeking offset feature is
supported by the protocol the socket belongs to.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This one is only considered for MSG_PEEK flag and the value pointed by
it specifies where to start peeking bytes from. If the offset happens to
point into the middle of the returned skb, the offset within this skb is
put back to this very argument.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes lines shorter and simplifies further patching.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

isdn source code uses a not-current coding style.

Update the coding style used on a per-line basis
so that git diff -w shows only elided blank lines
at EOF.

Done with emacs and some scripts and some typing.

Built x86 allyesconfig.
No detected change in objdump -d or size.
Signed-off-by: NJoe Perches <joe@perches.com>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch provides workaround for BUG in FW 7.2.16,
which in GRO mode may miscalculate buffer and
place on SGE one frag less than it could.
It may happen only for some MTUs, we mark these MTUs
with gro_check flag during device initialization or
MTU change.

Next FW should include fix for the issue and the
patch could be reverted.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with Tx only section for single cached SGEs.
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch integrates FW 7.2.16 HSI and implements driver
part of GRO flow.

FW 7.2.16 adds the ability to aggregate packets for GRO
(and not just LRO) and also fixes some bugs.

1. Added new aggregation mode: GRO. In this mode packets are aggregated
   such that the original packets can be reconstructed by the OS.
2. 57712 HW bug workaround - initialized all CAM TM registers to 0x32.
3. Adding the FCoE statistics structures to the BNX2X HSI.
4. Wrong configuration of TX HW input buffer size may cause theoretical
   performance effect. Performed configuration fix.
5. FCOE - Arrival of packets beyond task IO size can lead to crash.
   Fix firmware data-in flow.
6. iSCSI - In rare cases of on-chip termination the graceful termination
   timer hangs, and the termination doesn't complete. Firmware fix to MSL
   timer tolerance.
7. iSCSI - Chip hangs when target sends FIN out-of-order or with isles
   open at the initiator side. Firmware implementation corrected to drop
   FIN received out-of-order or with isles still open.
8. iSCSI - Chip hangs when in case of retransmission not aligned to 4-bytes
   from the beginning of iSCSI PDU. Firmware implementation corrected
   to support arbitrary aligned retransmissions.
9. iSCSI - Arrival of target-initiated NOP-IN during intense ISCSI traffic
   might lead to crash. Firmware fix to relevant flow.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes enic_probe to do a fw init devcmd for sriov vfs.
This enables vf driver in the guest to get into adapter init state without
having to explicitly issue an init fw cmd with portprofile info. But a
successful init on the vf will require the port profile information to be
pre-provisioned by the hypervisor via the pf
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the ndo_set_vf_mac netdev op to set the sriov vf mac
in adapter using the new fw devcmd CMD_SET_MAC_ADDR. During port profile
associate the pf driver gets the vf mac using CMD_GET_MAC_ADDR.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new devcmd CMD_SET_MAC_ADDR to set the mac address of an
interface.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

firmware devcmd CMD_MAC_ADDR gets the mac address of a vnic from adapter.
This patch renames it to CMD_GET_MAC_ADDR more appropriately.
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NChristian Benvenuti <benve@cisco.com>
Signed-off-by: NSujith Sankar <ssujith@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adapt adi ethernet driver to changes in bfin_get_ether_addr()
from arch/blackfin. bfin_get_ether_addr() returns now a state.
Set a random mac address via new eth_hw_addr_random() in case
the return value is not 0.

Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.

v2: change the logic to reduce unneeded checks
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changed bfin_get_ether_addr() to return a state and to
set no random mac address if the board don't provide one.

Let the caller of bfin_get_ether_addr() set a random mac
address if the return value is not 0.

v2: don't set random mac in bfin_get_ether_addr()
Signed-off-by: NDanny Kukawka <danny.kukawka@bisect.de>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct spelling "platfom" to "platform" in
drivers/net/ethernet/lantiq_etop.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8304859a "bnx2x: add fan failure event handling" made the function
bnx2x_close() non-static unnecessarily. The function is not called from
other sources. Make it static again.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c

Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.

The notable ones are:

* The at91 ata drivers both broke because of an earlier cleanup patch that
  some other patches were based on. Jean-Christophe decided to remove
  the legacy at91_ide driver and fix the new-style at91-pata driver while
  keeping the cleanup patch. I almost rejected the patches for being too
  late and too big but in the end decided to accept them because they
  fix a regression.

* A patch fixing build breakage from the sysdev-to-device conversion
  colliding with other changes touches a number of mach-s3c files.

* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
  is a mechanical change that unfortunately touches a lot of lines
  that should up in the diffstat.

* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  ARM: at91: drop ide driver in favor of the pata one
  pata/at91: use newly introduced SMC accessors
  ARM: at91: add accessor to manage SMC
  ARM: at91:rtc/rtc-at91sam9: ioremap register bank
  ARM: at91: USB AT91 gadget registration for module
  ep93xx: fix build of vision_ep93xx.c
  ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
  ARM: orion: Fix USB phy for orion5x.
  ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
  ARM: EXYNOS: Add cpu-offset property in gic device tree node
  ARM: EXYNOS: Bring exynos4-dt up to date
  ARM: OMAP3: cm-t35: fix section mismatch warning
  ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
  ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
  ARM: tegra: paz00: fix wrong SD1 power gpio
  i2c: tegra: Add devexit_p() for remove
  ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
  ARM: EXYNOS: Correct framebuffer window size on Nuri board
  ARM: SAMSUNG: Fix missing api-change from subsys_interface change
  ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
  ...

1) VETH_INFO_PEER netlink attribute needs to have it's size validated,
   from Thomas Graf.

2) 'poll' module option of bnx2x driver crashes the machine, just remove
   it.  From Michal Schmidt.

3) ks8851_mll driver reads the irq number from two places, but only
   initializes one of them, oops.  Use only one location and fix this
   problem, from Jan Weitzel.

4) Fix buffer overrun and unicast sterring bugs in mellanox mlx4 driver,
   from Eugenia Emantayev.

5) Swapped kcalloc() args in RxRPC and mlx4, from Axel Lin.

6) PHY MDIO device name regression fixes from Florian Fainelli.

7) If the wake event IRQ line is different from the netdevice one, we
   have to properly route it to the stmmac interrupt handler.  From
   Francesco Virlinzi.

8) Fix rwlock lock initialization ordering bug in mac80211, from
   Mohammed Shafi Shajakhan.

9) TCP lost_cnt can get out of sync, and in fact go negative, in certain
   circumstances.  Fix the way we specify what sequence range to operate
   on in tcp_sacktag_one() to fix this bug.  From Neal Cardwell.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
  net/ethernet: ks8851_mll fix irq handling
  veth: Enforce minimum size of VETH_INFO_PEER
  stmmac: update the driver version to Feb 2012 (v2)
  stmmac: move hw init in the probe (v2)
  stmmac: request_irq when use an ext wake irq line (v2)
  stmmac: do not discard frame on dribbling bit assert
  ipheth: Add iPhone 4S
  mlx4: add unicast steering entries to resource_tracker
  mlx4: fix QP tree trashing
  mlx4: fix buffer overrun
  3c59x: shorten timer period for slave devices
  netpoll: netpoll_poll_dev() should access dev->flags
  RxRPC: Fix kcalloc parameters swapped
  bnx2x: remove the 'poll' module option
  tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
  ks8851: Fix NOHZ local_softirq_pending 08 warning
  bnx2x: fix bnx2x_storm_stats_update() on big endian
  ixp4xx-eth: fix PHY name to match MDIO bus name
  octeon: fix PHY name to match MDIO bus name
  fec: fix PHY name to match fixed MDIO bus name
  ...

Fixes a bootstrapping issue for some registers when a less commonly used
method for register cache initialisation is used.  Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Fix cache defaults initialization from raw cache defaults

Merge tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Fixes maximum filename length and filesystem type reporting in statfs() calls
and also fixes stale inode mode bits on eCryptfs inodes after a POSIX ACL was
set on the lower filesystem's inode.

* tag 'ecryptfs-3.3-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  ecryptfs: remove the second argument of k[un]map_atomic()
  eCryptfs: Copy up lower inode attrs after setting lower xattr
  eCryptfs: Improve statfs reporting

pinctrl fixes for v3.3

* tag 'pinctrl-for-torvalds-20120216' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: restore pin naming

Here are a few more fixes for powerpc.  Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.

Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.

Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point.  For now let's just avoid
building it by default.  Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
  powerpc/adb: Use set_current_state()
  powerpc: Disable interrupts early in Program Check
  powerpc: Remove legacy iSeries from ppc64_defconfig
  powerpc/fsl/pci: Fix PCIe fixup regression
  powerpc: Fix kernel log of oops/panic instruction dump

One regression fix for SR-IOV on PPC and a couple of misc fixes from
Yinghai.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI: Fix pci cardbus removal
  PCI: set pci sriov page size before reading SRIOV BAR
  PCI: workaround hard-wired bus number V2