There were several places in the driver which could cause byte
ordering problem as provided by Al Viro
<viro@ZenIV.linux.org.uk>.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch makes the needlessly global qla2x00_issue_iocb_timeout()
static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch makes the following needlessly global functions static:
- qla2x00_alloc_work()
- qla2x00_post_work()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Original code would (incorrectly) only re-register after a
loop-down condition.  Also, FDMI registration should be enabled
by default.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The driver is incorrectly assuming that the 'sp' reference held
in qla2[x00|4xx]_abort_command() is valid after the mailbox
command is issued to abort the exchange.  It is *not*, as the
command may be completed during interrupt context before control
is returned to the mailbox caller.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Earlier code could trigger an infinite-retry if 1st invocation
returned a non-CS_COMPLETE status.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use the more efficient read-DMA'ble-buffer mailbox commands
rather than reading a single word/dword at a time.  We also
remove a bulk of the duplicate mailbox command-handling codes in
favor of more generic read-memory() routines (qla2xxx_dump_ram()
and qla24xx_dump_ram()).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

lpfc and qla2xxx overwrite the standard 'state' attribute with
custom callbacks. So rename the custom attributes to 'link_state'
and retain the original meaning of the 'state' attribute.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: NJames Smart <James.Smart@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: NTony Jones <tonyj@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Upon having configuration changes on vports only, the driver
handles SCR regardless physical port state and, in turn, it
results mailbox error as below:

	Mar 20 11:24:20 dl585 kernel: qla2x00_mailbox_command(9): **** FAILED.  mbx0=4005, mbx1=1, mbx2=8100, cmd=70 ****

With the changes, driver checks physical port loop_state and make
sure the port is ready to take commands.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Changes are added to the driver so that it can behave properly
upon having asynchronous events, for example, addition of target
devices to the VPs.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

As there is no actual cable connection on vports, made change so
that the driver checks DFLG_NO_CABLE against ha->device_flags
only for physical port.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

There were several places where referencing ha structure of
virtual ports for resources. Among those refereces, certain
fields are get up-to-dated only on ha structure of physical port.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The member is not needed as there's no non-scatter-gather
list I/Os submitted by the upper-layers.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NRavi Anand <ravi.anand@qlogic.com>
Additional cleanups and
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NRavi Anand <ravi.anand@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Now that infrastructure is present within the midlayer and there
is a clear distinction between what is expected from a device and
target reset, convert the current device-reset codes to a
target-reset, and add codes to perform a proper device-reset (LUN
reset).

In the process of adding reset support, collapse and consolidate
large sections of mailbox-command (TMF issuance) codes,
generalize the two 'wait-for-commands-to-complete' functions, and
add a generic-reset routine for use by midlayer reset functions.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Some switches return 0x09 (Command not supported) as the reason
code for GPSC failure.  Check for this code, and disable
additional GPSC queries if found.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The Flash Descriptor Table (FDT) present on many recent HBAs
encodes flash accessing characteristics of the flash-part used on
the HBA.  Use this information during flash manipulation (writes)
rather than using specific hard-coded values based on queried
manufacturer and device IDs.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Strip unused (DEBUG-ONLY) enabled functions, inlines, useless
wrappers, and unused DPC flags from the code.  Another step in
the migration towards a cleaner (less-crusty) driver.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Recent ISPs have a region within FLASH which acts as a repository
for the logging of serious hardware and software failures.
Currently, the region is large enough to support up to 255
entries.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Supported events include LIP, LIP reset, RSCN, link up, and link
down.

To support AEN (and additional forthcoming features), we also
introduce a simple deferred-work construct to manage events which
require a non-atomic sleeping-capable context.  This work-list is
processed as part of the driver's standard DPC routine.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

There's no need to use the heavier (albiet safer)
*_irq[save|restore]() locking primitives within the driver's
interrupt handlers, interrupts are guaranteed to be
non-reentrant.  Use lightweight spin_lock() and spin_unlock()
primitives while acquiring the hardware_lock.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Rather than using a duplicate/cached value stored in the driver's
internal fcport structure.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use generic FC transport #defines for speed values.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The original code would incorrectly hardcode ELS timeout values
rather than using the traditional '2 * r_a_tov' value.  In some
cases, the hardcoded values would be larger than the
mailbox-command-timeout and result in a needless BIG_HAMMER (ISP
reset), the typical recovery mechanism employed in such cases.

The second defect in the original code was in the assignment of
the default 'ha->r_a_tov' to twice the traditional value.
Correct this by setting the value to 10 seconds.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

For recent ISPs, software must detect OVERRUN conditions by
checking the SS_RESIDUAL_OVER bit during CS_COMPLETE handling.
Update the driver to perform this check, which is consistent with
what earlier firmwares did by explicitly cracking open the
FCP_RSP statuses and returning an CS_DATA_OVERRUN.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

There's no point in hitting the RISC with what will most
assuredly be an unsucessful reset of the RISC hardware if the
initial stop-firmware mailbox command fails with a time-out
status.  Instead, to avoid what could amount to a lengthy
stop-firmware/detect-failure/reset-risc loop, continue with
driver unloading and discard the stop-firmware requirement.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

scsi/qla2xxx/qla_dfs.c: In function 'qla2x00_dfs_fce_show':
scsi/qla2xxx/qla_dfs.c:26: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'uint64_t'
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Correct issue where incorrect init-fw mailbox command was used on non-NPIV capable ISPs.

BIT_2 of the firmware attributes is only valid on FW-interface-2
type HBAs.  Code in commit
c48339de would cause the
incorrect initialize-firmware mailbox command to be issued for
non-NPIV capable ISPs.  Correct this by reverting to previously
used (and correct) pre-condition 'if' check.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 For following fc_host specific attributes, vports rely on the pport.
 So, this patch changed way to access the data for those attributes so that
 they can access pport's.
 - get_host_speed (speed)
 - get_host_port_state (port_state)
 - get_host_port_type (port_type)
 - get_fc_host_stats

Also, added PORT_SPEED_8GB case in the speed attribute for 8Gb HBAs.
Signed-Off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>