The current practice is to not add _clk suffixes to clock node names in
DT, as these names are used as the actual clock names.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The scif_clk and pcie_bus_clk device nodes are already enabled in
r8a7795.dtsi, so there is no need to update their statuses again.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The EthernetAVB should not depend on the bootloader to setup correct
drive-strength values. Values for drive-strength where found by
examining the registers after the bootloader has configured the
registers and successfully used the EthernetAVB.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Set PHY rxc-skew-ps to 1500 and all other values to their default values.

This is intended to to address failures in the case of 1Gbps communication
using the by salvator-x board with the KSZ9031RNX phy. This has been
reported to occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables I2C for DVFS device for for Salvator-X board on
R8A7795 SoC.
Signed-off-by: NKeita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>

This patch adds MIX (= Mixer) support.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds CTU (= Channel Transfer Unit) support which is needed
to sound mixing.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Declaring the endpoint makes LVDS enablement easier by just including
the corresponding panel's dtsi file.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Only the VGA output is supported for now.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

We have to set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch also adds a regulator node for USB2.0 to handle VBUS on/off
by the phy-rcar-gen3-usb2 driver.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables watchdog timer for Salvator-X board.
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

On the Salvator-X development board, the RTS and CTS pins of debug
serial-1 port SCIF1 are wired to the CP2102 Serial-USB bridge.  Reflect
this in the DTS by adding the "uart-has-rtscts" property to the scif1
device node.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.

Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Reported-by: NJürg Billeter <j@bitron.ch>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

It can be used for the watchdog.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Since 16ccaf5b ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.

This patch updates the kzm9g device tree to use the generic properties.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

We should set SW15 to pin 2-3 side on the board before we use CN9
as USB host or peripheral.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This board has a MAX3355 chip. However, we cannot use the extcon/max3355
driver because the ID pin doesn't connect to a gpio pin (in other words,
it connects to the SoC specific pin).
And, the phy-rcar-gen3-usb2 driver cannot handle such a chip for now.
So, this patch enables usb2_phy of channel 1 and 2.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the exposed SD card slots. The on-board eMMC needs to wait until we
fixed the 8bit support.
Signed-off-by: NAi Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.

This increases the range and accuracy of supported baud rates:
  - SCIF:
      - Supports now 50, 230400, 460800, 500000, and 921600 bps,
      - Perfect match for standard 50-460800, and 9216000 bps.
  - HSCIF:
      - Supports now 50, 75, and 110 bps,
      - Perfect match for standard 50-460800, and 9216000 bps.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This enables SATA device in r8a7795-salvator-x.dts.
Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

CS2000 needs AUDIO_CLKOUT as master clock which is generated
by Renesas sound, and Renesas sound needs CS2000 as ADUIO_CLK_B.
Because of this relationship, it will be dead-lock when driver probe.

cs2000: clk_multiplier@4f {
        ...
        clocks = <&rcar_sound 0>, <&x12_clk>;
        ...
};

&rcar_sound {
        ...
        assigned-clocks = <&cs2000>;
        ...
};

This patch is using dummy audio_clkout to avoid this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

DMA transfer to/from SSIU

     DMA
[MEM] -> [SSIU] -> [SSI]

     DMA
[MEM] <- [SSIU] <- [SSI]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

DMA transfer to/from SSI

     DMA
[MEM] -> [SSI]

     DMA
[MEM] <- [SSI]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds PIO sound support for Salvator-X board.
It can use 44.1kHz base sound only at this point, since 48kHz base
sound needs CS2000, but it is not yet upstreamed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Add an ethernet0 alias for the wired network card so that U-Boot can
find the device-node and add an appropriate "local-mac-address"
property.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

As has been the practice for boards for 32bit ARM Renesas SoCs
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>