Too many drivers fail at IOPORT vs IOMEM checking before blindly calling
in to the API, so we may as well just provide basic stubs to get more
build coverage. Other platforms already do this, too (tile, parisc, etc.)
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Conflicts:
	arch/sh/Kconfig
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The RSK2+SH7264 board uses the sh7264 processor. It is often
referred to as just rsk7264. NOR Flash, SDRAM, serial, USB Host and
ethernet are working.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is an sh2a device with FPU, video display controller (VDC),
8 serial ports, 3 I2C channels, 2 CAN ports, SD and on-chip USB.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Pull ARM: SoC fixes from Olof Johansson:
 "Things have slowed down a lot for us, but we have five more fixes for
  omap and kirkwood below.  Three are for boards setup issues, two are
  SoC-level fixes."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP: igep0020: fix smsc911x dummy regulator id
  ARM: orion5x: Fix GPIO enable bits for MPP9
  ARM: kirkwood: add missing kexec.h include
  ARM: OMAP: Revert "ARM: OMAP: ctrl: Fix CONTROL_DSIPHY register fields"
  ARM: OMAP1: Amstrad Delta: Fix wrong IRQ base in FIQ handler

Pull last minute regman bug fix from Mark Brown:
 "This is a last minute bug fix that was only just noticed since the
  code path that's being exercised here is one that is fairly rarely
  used.  The changelog for the change itself is extremely clear and the
  code itself is obvious to inspection so should be pretty safe."

* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: fix possible memory corruption in regmap_bulk_read()

Pull KVM fixes from Avi Kivity:
 "Two asynchronous page fault fixes (one guest, one host), a powerpc
  page refcount fix, and an ia64 build fix."

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: ia64: fix build due to typo
  KVM: PPC: Book3S HV: Fix refcounting of hugepages
  KVM: Do not take reference to mm during async #PF
  KVM: ensure async PF event wakes up vcpu from halt

Pull powerpc fixes from Benjamin Herrenschmidt:
 "Here are a couple of last minute fixes for 3.4 for regressions
  introduced by my rewrite of the lazy irq masking code."

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/irq: Make alignment & program interrupt behave the same
  powerpc/irq: Fix bug with new lazy IRQ handling code

Merge tag 'omap-fixes-for-v3.4-rc6-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fix two board spefific regressions and one regression caused by bad documentation

By Archit Taneja (1) and others
via Tony Lindgren
* tag 'omap-fixes-for-v3.4-rc6-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP: igep0020: fix smsc911x dummy regulator id
  ARM: OMAP: Revert "ARM: OMAP: ctrl: Fix CONTROL_DSIPHY register fields"
  ARM: OMAP1: Amstrad Delta: Fix wrong IRQ base in FIQ handler

id 0 is already used and causes errors at boot:

WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0x9c/0xac()
sysfs: cannot create duplicate filename '/devices/platform/reg-fixed-voltage.0'

Fix it by using the next available one (id=1).

This was caused by 5b3689f4 (ARM: OMAP2+: smsc911x: Add fixed
board regulators) that did not account for some regulators
already being used.
Signed-off-by: NEnrico Butera <ebutera@users.berlios.de>
[tony@atomide.com: updated comments for regression causing commit]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The function regmap_bulk_read() calls the regmap_read() for
each register if set of register has volatile and cache is
enabled. In this case, last few register read makes the memory
corruption if the register size is not the size of unsigned int.
The regam_read() takes argument as unsigned int for returning
value and it update the value as
	*val = map->format.parse_val(map->work_buf);
This causes complete 4 bytes (size of unsigned int) to get written.
Now if client pass the memory pointer for value which is equal to the
required size of register count in regmap_bulk_read() then last few
register read actually update the memory beyond passed pointer size.

Avoid this by using local variable for read and then do memcpy()
for actual byte copy to passed pointer based on register size.

I allocated one pointer ptr and take first 16 bytes dump of that
pointer then call regmap_bulk_read() with pointer which is just
on top of this allocated pointer and register count of 128. Here
register size is 1 byte.
The memory trace of last 5 register read are as follows:

[    5.438589] regmap_bulk_read after regamp_read() for register 122
[    5.447421] 0xef993c20 0xef993c00 0x00000000 0x00000001
[    5.467535] regmap_bulk_read after regamp_read() for register 123
[    5.476374] 0xef993c20 0xef993c00 0x00000000 0x00000001
[    5.496425] regmap_bulk_read after regamp_read() for register 124
[    5.505260] 0xef993c20 0xef993c00 0x00000000 0x00000001
[    5.525372] regmap_bulk_read after regamp_read() for register 125
[    5.534205] 0xef993c00 0xef993c00 0x00000000 0x00000001
[    5.554258] regmap_bulk_read after regamp_read() for register 126
[    5.563100] 0xef990000 0xef993c00 0x00000000 0x00000001
[    5.554258] regmap_bulk_read after regamp_read() for register 127
[    5.587108] 0xef000000 0xef993c00 0x00000000 0x00000001

Here it is observed that the memory content at first word started changing
on last 3 regmap_read() and so corruption happened.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

s/kcm/kvm/.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Merge branch 'kirkwood_fixes_for_v3.4' of git://git.infradead.org/users/jcooper/linux-kirkwood into fixes

By Ben Hutchings (1) and Ian Campbell (1)
via Jason Cooper: "ARM: kirkwood: fixes for v3.4"
* 'kirkwood_fixes_for_v3.4' of git://git.infradead.org/users/jcooper/linux-kirkwood:
  ARM: orion5x: Fix GPIO enable bits for MPP9
  ARM: kirkwood: add missing kexec.h include

Alignment was the last user of the ENABLE_INTS macro, which we can
now remove. All non-syscall exceptions now disable interrupts on
entry, they get re-enabled conditionally from C code. Don't
unconditionally re-enable in program check either, check the
original context.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We had a case where we could turn on hard interrupts while
leaving the PACA_IRQ_HARD_DIS bit set in the PACA. This can
in turn cause a BUG_ON() to hit in __check_irq_replay() due
to interrupt state getting out of sync.

The assembly code was also way too convoluted. Instead, we
now leave it to the C code to do the right thing which ends
up being smaller and more readable.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 554cdaef ('ARM: orion5x: Refactor
mpp code to use common orion platform mpp.') seems to have accidentally
inverted the GPIO valid bits for MPP9 (only).  For the mv2120 platform
which uses MPP9 as a GPIO LED device, this results in the error:

[   12.711476] leds-gpio: probe of leds-gpio failed with error -22
Reported-by: NHenry von Tresckow <hvontres@gmail.com>
References: http://bugs.debian.org/667446Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org [v3.0+]
Tested-by: NHans Henry von Tresckow <hvontres@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Pull regulator fixes from Mark Brown:
 "One small fix for an edge condition in the max8997 driver and a fix
  for a surprise in the devres API which caused devm_regulator_put() to
  not actually put the regulator - a nicer version of this based on an
  improvement of the devres API is queued for 3.5."

* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: Actually free the regulator in devm_regulator_put()
  regulator: Fix the logic to ensure new voltage setting in valid range

Fixes the following build error when CONFIG_KEXEC is enabled:
  CC      arch/arm/mach-kirkwood/board-dt.o
arch/arm/mach-kirkwood/board-dt.c: In function 'kirkwood_dt_init':
arch/arm/mach-kirkwood/board-dt.c:52:2: error: 'kexec_reinit' undeclared (first use in this function)
arch/arm/mach-kirkwood/board-dt.c:52:2: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: NIan Campbell <ijc@hellion.org.uk>
[v4, rebase onto recent Linus for repost]
[v3, speak actual English in the commit message, thanks Sergei Shtylyov]
[v2, using linux/kexec.h not asm/kexec.h]
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Pull drm fixes from Dave Airlie:
 "Two fixes from Intel, one a regression, one because I merged an early
  version of a fix.

  Also the nouveau revert of the i2c code that was tested on the list."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau/i2c: resume use of i2c-algo-bit, rather than custom stack
  drm/i915: Do no set Stencil Cache eviction LRA w/a on gen7+
  drm/i915: disable sdvo hotplug on i945g/gm

Merge tag 'stable/for-linus-3.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull xen fixes from Konrad Rzeszutek Wilk:
 - fix to Kconfig to make it fit within 80 line characters,
 - two bootup fixes (AMD 8-core and with PCI BIOS),
 - cleanup code in a Xen PV fb driver,
 - and a crash fix when trying to see non-existent PTE's

* tag 'stable/for-linus-3.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/Kconfig: fix Kconfig layout
  xen/pci: don't use PCI BIOS service for configuration space accesses
  xen/pte: Fix crashes when trying to see non-existent PGD/PMD/PUD/PTEs
  xen/apic: Return the APIC ID (and version) for CPU 0.
  drivers/video/xen-fbfront.c: add missing cleanup code

Pull two percpu fixes from Tejun Heo:
 "One adds missing KERN_CONT on split printk()s and the other makes
  the percpu allocator avoid using PMD_SIZE as atom_size on x86_32.

  Using PMD_SIZE led to vmalloc area exhaustion on certain
  configurations (x86_32 android) and the only cost of using PAGE_SIZE
  instead is static percpu area not being aligned to large page
  mapping."

* 'for-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu, x86: don't use PMD_SIZE as embedded atom_size on 32bit
  percpu: use KERN_CONT in pcpu_dump_alloc_info()

Pull ARM fixes from Russell King:
 "This is mainly audit fixes, found by folks who happened to enable this
  feature and then found it broke their user applications."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7414/1: SMP: prevent use of the console when using idmap_pgd
  ARM: 7412/1: audit: use only AUDIT_ARCH_ARM regardless of endianness
  ARM: 7411/1: audit: fix treatment of saved ip register during syscall tracing
  ARM: 7410/1: Add extra clobber registers for assembly in kernel_execve

With the embed percpu first chunk allocator, x86 uses either PAGE_SIZE
or PMD_SIZE for atom_size.  PMD_SIZE is used when CPU supports PSE so
that percpu areas are aligned to PMD mappings and possibly allow using
PMD mappings in vmalloc areas in the future.  Using larger atom_size
doesn't waste actual memory; however, it does require larger vmalloc
space allocation later on for !first chunks.

With reasonably sized vmalloc area, PMD_SIZE shouldn't be a problem
but x86_32 at this point is anything but reasonable in terms of
address space and using larger atom_size reportedly leads to frequent
percpu allocation failures on certain setups.

As there is no reason to not use PMD_SIZE on x86_64 as vmalloc space
is aplenty and most x86_64 configurations support PSE, fix the issue
by always using PMD_SIZE on x86_64 and PAGE_SIZE on x86_32.

v2: drop cpu_has_pse test and make x86_64 always use PMD_SIZE and
    x86_32 PAGE_SIZE as suggested by hpa.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NYanmin Zhang <yanmin.zhang@intel.com>
Reported-by: NShuoX Liu <shuox.liu@intel.com>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4F97BA98.6010001@intel.com>
Cc: stable@vger.kernel.org

The H_REGISTER_VPA hcall implementation in HV Power KVM needs to pin some
guest memory pages into host memory so that they can be safely accessed
from usermode.  It does this used get_user_pages_fast().  When the VPA is
unregistered, or the VCPUs are cleaned up, these pages are released using
put_page().

However, the get_user_pages() is invoked on the specific memory are of the
VPA which could lie within hugepages.  In case the pinned page is huge,
we explicitly find the head page of the compound page before calling
put_page() on it.

At least with the latest kernel, this is not correct.  put_page() already
handles finding the correct head page of a compound, and also deals with
various counts on the individual tail page which are important for
transparent huge pages.  We don't support transparent hugepages on Power,
but even so, bypassing this count maintenance can lead (when the VM ends)
to a hugepage being released back to the pool with a non-zero mapcount on
one of the tail pages.  This can then lead to a bad_page() when the page
is released from the hugepage pool.

This removes the explicit compound_head() call to correct this bug.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Acked-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Fit it into 80 columns so that it is readable in menuconfig.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

The accessing PCI configuration space with the PCI BIOS32 service does
not work in PV guests.

On systems without MMCONFIG or where the BIOS hasn't marked the
MMCONFIG region as reserved in the e820 map, the BIOS service is
probed (even though direct access is preferred) and this hangs.

CC: stable@kernel.org
Acked-by: NJan Beulich <jbeulich@suse.com>
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
[v1: Fixed compile error when CONFIG_PCI is not set]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

If I try to do "cat /sys/kernel/debug/kernel_page_tables"
I end up with:

BUG: unable to handle kernel paging request at ffffc7fffffff000
IP: [<ffffffff8106aa51>] ptdump_show+0x221/0x480
PGD 0
Oops: 0000 [#1] SMP
CPU 0
.. snip..
RAX: 0000000000000000 RBX: ffffc00000000fff RCX: 0000000000000000
RDX: 0000800000000000 RSI: 0000000000000000 RDI: ffffc7fffffff000

which is due to the fact we are trying to access a PFN that is not
accessible to us. The reason (at least in this case) was that
PGD[256] is set to __HYPERVISOR_VIRT_START which was setup (by the
hypervisor) to point to a read-only linear map of the MFN->PFN array.
During our parsing we would get the MFN (a valid one), try to look
it up in the MFN->PFN tree and find it invalid and return ~0 as PFN.
Then pte_mfn_to_pfn would happilly feed that in, attach the flags
and return it back to the caller. 'ptdump_show' bitshifts it and
gets and invalid value that it tries to dereference.

Instead of doing all of that, we detect the ~0 case and just
return !_PAGE_PRESENT.

This bug has been in existence .. at least until 2.6.37 (yikes!)

CC: stable@kernel.org
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

On x86_64 on AMD machines where the first APIC_ID is not zero, we get:

ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] enabled)
BIOS bug: APIC version is 0 for CPU 1/0x10, fixing up to 0x10
BIOS bug: APIC version mismatch, boot CPU: 0, CPU 1: version 10

which means that when the ACPI processor driver loads and
tries to parse the _Pxx states it fails to do as, as it
ends up calling acpi_get_cpuid which does this:

for_each_possible_cpu(i) {
        if (cpu_physical_id(i) == apic_id)
                return i;
}

And the bootup CPU, has not been found so it fails and returns -1
for the first CPU - which then subsequently in the loop that
"acpi_processor_get_info" does results in returning an error, which
means that "acpi_processor_add" failing and per_cpu(processor)
is never set (and is NULL).

That means that when xen-acpi-processor tries to load (much much
later on) and parse the P-states it gets -ENODEV from
acpi_processor_register_performance() (which tries to read
the per_cpu(processor)) and fails to parse the data.
Reported-by-and-Tested-by: NStefan Bader <stefan.bader@canonical.com>
Suggested-by: NBoris Ostrovsky <boris.ostrovsky@amd.com>
[v2: Bit-shift APIC ID by 24 bits]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

It turns out that (quite surprisingly) devres_destroy() only undoes the
devres mapping, it doesn't destroy the underlying resource, meaning that
anything using devm_regulator_put() would leak. While we wait for the new
devres_release() which does what we want to get merged open code it in
devm_regulator_put().
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The operations in the subsequent error-handling code appear to be also
useful here.
Acked-by: NFlorian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
[v1: Collapse some of the error handling functions]
[v2: Fix compile warning]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>

Previous issues with i2c-algo-bit have now been resolved.

This is a revert of f553b79c mostly,
due to fixes in the i2c core repairing the original issue, this code
isn't required and was causing regressions.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Reported-by: NNick Bowler <nbowler@elliptictech.com>
Tested-by: NNick Bowler <nbowler@elliptictech.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Daniel wrote:

2 little patches:
- One regression fix to disable sdvo hotplug on broken hw.
- One patch to upconvert the snb hang workaround from patch v1 to patch
 v2.

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Do no set Stencil Cache eviction LRA w/a on gen7+
  drm/i915: disable sdvo hotplug on i945g/gm

I've flagged this while reviewing the first version and Ken Graunke
fixed it up in v2, but unfortunately Dave Airlie picked up the wrong
version.

Cc: Dave Airlie <airlied@redhat.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: stable@kernel.org
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Chris Wilson dug out a hw erratum saying that there's noise on the
interrupt line on i945G chips. We also have a bug report from a i945GM
chip with an sdvo hotplug interrupt storm (and no apparent cause).

Play it safe and disable sdvo hotplug on all i945 variants.

Note that this is a regression that has been introduced in 3.1,
when we've enabled sdvo hotplug support with

commit cc68c81a
Author: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Date:   Wed Sep 21 17:13:30 2011 +0100

    drm/i915: Enable SDVO hotplug interrupts for HDMI and DVI

Cc: stable@kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=38442Reported-and-tested-by: NDominik Köppl <dominik@devwork.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Commit ce7e5d2d ("x86: fix broken TASK_SIZE for ia32_aout") breaks
kernel builds when "CONFIG_IA32_AOUT=m" with

  ERROR: "set_personality_ia32" [arch/x86/ia32/ia32_aout.ko] undefined!
  make[1]: *** [__modpost] Error 1

The entry point needs to be exported.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NAl Viro <viro@zeniv.linux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes form Peter Anvin

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
  arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
  x86, relocs: Remove an unused variable
  asm-generic: Use __BITS_PER_LONG in statfs.h
  x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it

Pull btrfs fixes from Chris Mason:
 "The big ones here are a memory leak we introduced in rc1, and a
  scheduling while atomic if the transid on disk doesn't match the
  transid we expected.  This happens for corrupt blocks, or out of date
  disks.

  It also fixes up the ioctl definition for our ioctl to resolve logical
  inode numbers.  The __u32 was a merging error and doesn't match what
  we ship in the progs."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: avoid sleeping in verify_parent_transid while atomic
  Btrfs: fix crash in scrub repair code when device is missing
  btrfs: Fix mismatching struct members in ioctl.h
  Btrfs: fix page leak when allocing extent buffers
  Btrfs: Add properly locking around add_root_to_dirty_list

Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there.  Switch to use of set_personality_ia32()...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>