* Add IDE_HFLAG_MMIO host flag and set it for hosts which use
  default_hwif_mmiops().

v2:
* Fix kernel panic in pmac host driver (',' should be '|').

  Thanks to Kamalesh for reporting it + testing the fix
  and to Andrew for hinting me about the source of the issue.

Cc: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

v2:

* Update ->{in,out}_data methods to take 'struct request *rq' argument.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

v2:

* Update ->{in,out}_data methods to take 'struct request *rq' argument.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

v2:

* Update ->{in,out}_data methods to take 'struct request *rq' argument
  (thanks to Stephen Rothwell for catching it).

There should be no functional changes caused by this patch.

Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
  into new ->{in,out}put_data methods which take number of bytes to
  transfer as an argument and always do padding.

While at it:

* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.

There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods to
  falconide and q40ide host drivers (->ata_* methods are implemented on
  top of ->atapi_* methods so they also do byte-swapping now).

* Cleanup atapi_{in,out}put_bytes().

v2:
* Add 'struct request *rq' argument to ->ata_{in,out}put_data methods
  and don't byte-swap disk fs requests (we shouldn't un-swap fs requests
  because fs itself is stored byte-swapped on the disk) - this is how
  things were done before the patch (ideally device mapper should be
  used instead but it would break existing setups and would have some
  performance impact).

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Richard Zidlicky <rz@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

On Monday 28 April 2008, Sergei Shtylyov wrote:
> Hello, I wrote:
> 
> > Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:
> 
> > include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared 
> > `static' but never defined
> > include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
> >  `static' but never defined
> 
> > by wiping out the whole "function prototyping" section from the header file
> > <asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
> > already dead in the IDE driver; move the only useful prototype into the driver.
> > 
> > Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
> 
> > ---
> > I'm not sure thru which tree this should go -- probably thru Linux/MIPS one...
> 
> > Bart, au1xxx-ide-fix-mwdma-support.patch will probably need to be updated to
> > remove that added prototype since it won't be needed anymore...
> 
>     Which you haven't done either in that patch or in 
> au1xxx-ide-use-init_dma-method.patch. So, face the consequences:
> 
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:51: warning: 'auide_ddma_init' used but never
> defined

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* endianness annotations
* endianness fixes
* missing get_unaligned/put_unaligned

It's pretty much all over the place, changes to different files are independent.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Serial-parts-Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

usb_control_msg() converts arguments to little-endian itself,
doing that in caller means breakage on big-endian boxen.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

again, fallout from ide merge
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

it's ata_link, not ata_linke
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Since both the IDE interface and SMC 91C111 Ethernet chip are on-board
devices, not SOC devices, move the platform device registration form the
common to the board specific code.

While at it, remove semicolon (which didn't break compilation only by
chance) from the AU1XXX_ATA_DDMA_REQ macro and do some renaming:

- change 'au1200_ide0_' variable name prefix to the mere 'ide_';

- change 'smc91x_' variable name prefix to 'smc91c111_' since that's the
  name of the chip used on the boards;

- drop 'AU1XXX_' prefix from the names of macros describing IDE and Ethernet
  on-board devices;

- change 'SMC91111_' to 'SMC91C111_', change 'IRQ' to 'INT' in the names of
  the macros describing the Ethernet chip for consistency with the IDE
  macros;

- change 'ATA_' to 'IDE_' and 'OFFSET' to 'SHIFT' (since this value is
  indeed a shift count) in the names of the macros describing the IDE
  interface.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The platform is actually named routerboard 532 so let's call it this.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NJeff Garzik <jeff@garzik.org>

Move the code registering the Alchemy UART platform devices from
drivers/serial/ to its proper place, into the Alchemy platform code.  Fix
the related Kconfig entry, while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Convert quirk printks to dev_printk().

[akpm@linux-foundation.org: fix warnings, improve output text]
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

print_fn_descriptor_symbol() prints the address if we don't have a symbol,
so no need to print both.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Every PNP device should have a valid protocol pointer.  If it doesn't,
something's wrong and we should oops so we can find and fix the problem.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.

A simplified version of the semantic patch making this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@ change_compare_np @
expression E;
@@

(
- jiffies <= E
+ time_before_eq(jiffies,E)
|
- jiffies >= E
+ time_after_eq(jiffies,E)
|
- jiffies < E
+ time_before(jiffies,E)
|
- jiffies > E
+ time_after(jiffies,E)
)

@ include depends on change_compare_np @
@@

#include <linux/jiffies.h>

@ no_include depends on !include && change_compare_np @
@@

  #include <linux/...>
+ #include <linux/jiffies.h>
// </smpl>

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character.  It may also output a trailing space
before newline.  klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file.  This looks ugly.

Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar.  Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

strict_strtoul handles the open-coded sanity checks in
raid5_store_stripe_cache_size and raid5_store_preread_threshold
Acked-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve write performance by preventing the delayed_list from dumping all its
stripes onto the handle_list in one shot.  Delayed stripes are now further
delayed by being held on the 'hold_list'.  The 'hold_list' is bypassed when:

  * a STRIPE_IO_STARTED stripe is found at the head of 'handle_list'
  * 'handle_list' is empty and i/o is being done to satisfy full stripe-width
    write requests
  * 'bypass_count' is less than 'bypass_threshold'.  By default the threshold
    is 1, i.e. every other stripe handled is a preread stripe provided the
    top two conditions are false.

Benchmark data:
System: 2x Xeon 5150, 4x SATA, mem=1GB
Baseline: 2.6.24-rc7
Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean
Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048
  * patched:  +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512)

Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS)
  * patched: +13%
  * patched + preread_bypass_threshold = 0: +37%

Changes since v1:
* reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and
  make it configurable.  This defaults to fairness and modest performance
  gains out of the box.
Changes since v2:
* [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not
  necessary, the important change was clearing STRIPE_DELAYED in
  add_stripe_bio and this has been moved out to make_request for the hang
  fix.
* [neilb@suse.de]: simplify get_priority_stripe
* [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is
  sampled empty (+11%)
* [dan.j.williams@intel.com]: decrement the bypass_count at the detection
  of stripes being naturally promoted off of hold_list +2%.  Note, resetting
  bypass_count instead of decrementing on these events yields +4% but that is
  probably too aggressive.
Changes since v3:
* cosmetic fixups
Tested-by: NJames W. Laferriere <babydr@baby-dragons.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/md/md.c:734:16: warning: Using plain integer as NULL pointer
drivers/md/md.c:1115:16: warning: Using plain integer as NULL pointer

Add some braces to match the else-block as well.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a couple of error-patch oopses identified by Marcio Buss in
http://bugzilla.kernel.org/show_bug.cgi?id=9567.

Cc: Marcio Buss <marciobuss@gmail.com>
Cc: Jeff Zhou <xinzhou.sjtu@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the 965G and 965GM graphic chipsets to the intelfb driver.  I
have a notebook with an Intel Mobile GM965/GL960 Integrated Graphics
Controller and with the attached patch the framebuffer comes up.  I have
tested it a bit with DirectFB to make sure it is working stable.

I also have an Intel Mobile GM945 and I compared the results, the programming
interface of the 9xx series from Intel is mostly the same, so I think the
patch should add all the functionality which the 945GM has.
Signed-off-by: NMaik Broemme <mbroemme@plusserver.de>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Antonino Daplas <adaplas@pol.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Note: looks like accesses to "registered_fb" are done without any exclusion
so there're none in new proc code, too. This should be fixed in separate
patch.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix bug identified by Daniel Marjamki: `m' is leaked on the error path.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=10452

Cc: Daniel Marjamki <danielm77@spray.se>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch splits hecubafb into the platform independent hecubafb and the
platform dependent n411.
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Right now, if request_irq or anthing after it fails than we free the firmware
for the second time what might end bad :)
Signed-off-by: NSebastian Siewior <sebastian@breakpoint.cc>
Acked-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch splits metronomefb into the platform independent metronomefb and
the platform dependent am200epd.
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch is a bugfix for hecubafb_write which would return an incorrect
error value for the bytecount from framebuffer writes.
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch is a bugfix for the use of cfb_* functions instead of sys_*
functions.  sys_* should be used with vmalloced framebuffers.  the previous
cfb_ use would not work for callers of imageblit/etc.
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The following features are supported:
plane 0 works as a regular frame buffer, can be accessed by /dev/fb0
plane 1 has two AOIs (area of interest), can be accessed by /dev/fb1 and /dev/fb2
plane 2 has two AOIs, can be accessed by /dev/fb3 and /dev/fb4
Special ioctls support AOIs

All /dev/fb* can be used as regular frame buffer devices, except hardware
change can only be made through /dev/fb0.  Changing pixel clock has no effect
on other fbs.

Limitation of usage of AOIs:
AOIs on the same plane can not be horizonally overlapped
AOIs have horizonal order, i.e. AOI0 should be always on top of AOI1
AOIs can not beyond phisical display area. Application should check AOI geometry
before changing physical resolution on /dev/fb0

required command line parameters to preallocate memory for frame buffer diufb.

optional command line parameters to set modes and monitor
video=fslfb:[resolution][,bpp][,monitor]
Syntax:

Resolution
xres x yres-bpp@refresh_rate, the -bpp and @refresh_rate are optional
eg, 1024x768, 1280x1024, 1280x1024-32, 1280x1024@60, 1280x1024-32@60, 1280x480-32@60

Bpp
bpp=32, bpp=24, or bpp=16

Monitor
monitor=0, monitor=1, monitor=2
0 is DVI
1 is Single link LVDS
2 is Double link LVDS

Note: switching monitor is a board feather, not DIU feather. MPC8610HPCD has three
monitor ports to swtich to. MPC5121ADS doesn't have additional monitor port. So switching
monirot port for MPC5121ADS has no effect.

If compiled as a module, it takes pamameters mode, bpp, monitor with the same syntax above.
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NTimur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mostly signedness fixes.  nv10_sim_state existence in both drivers suggests
that one of them should be removed, but that's for later.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Both FB_RIVA and FB_NVIDIA depends on PCI, so CONFIG_PCI always defined for
them.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>