This code doesn't use pci_assign_resource() and ide_get_or_set_dma_base() uses
pci_resource_start() to get DMA base address so it has no chance of working.
Moreover this belongs to PCI quirks (in case somebody would like to fix it).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Clear prefetch and postwrite for ATAPI devices instead of depending on BIOS.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Don't force PIO4 when programming UDMA mode (suggested by Sergei).
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

noautodma can now be unexported.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

static code mustn't be exported.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since ide-pmac allows separate PIO and DMA timings, and ide-pmac always sets
->autotune this change shouldn't have any other effect than bringing ide-pmac
driver in-line with other host drivers wrt ->ide_dma_check implementation.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since ide-cris allows separate PIO and DMA timings, and ide-cris always sets
->autotune this change shouldn't have any other effect than bringing ide-cris
driver in-line with other host drivers wrt ->ide_dma_check implementation.

Cc: Mikael Starvik <starvik@axis.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since sl82c105 re-programs DMA/PIO timings for DMA enable/disable, and sets
->autotune this change shouldn't have any other effect than bringing sl82c105
driver in-line with other host drivers wrt ->ide_dma_check implementation.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add PIO autotune fallback to ->ide_dma_check.

  Since cs5530/sc1200 allow separate PIO and DMA timings, and cs5530/sc1200
  always set ->autotune this change shouldn't have any other effect than
  bringing these drivers in-line with other host drivers wrt ->ide_dma_check
  implementations.

* Fix ->ide_dma_check to return "-1" if DMA cannot be set.

* Bump driver version.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check.  All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Several host drivers used to reset drive->init_speed in their ->ide_dma_check
implementations which resulted in incorrect init speed being reported to the
user, fix it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove needless setting of drive->using_dma from auide_dma_check().

* Split off auide_mdma_filter() from auide_dma_check().

* Use ide_tune_dma() in auide_dma_check(), this fixes following issues:
  - device's DMA capability bit not being checked
  - device not being checked against generic DMA blacklist
  - transfer mode not being set on device/host

* Add PIO autotune fallback to auide_dma_check().
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Fix handling of unsupported/invalid modes in atiixp_set_dma_mode().

* ATI controllers allow separate PIO and DMA timings so remove programming
  of PIO modes from atiixp_set_dma_mode().  Also remove no longer needed
  atiixp_dma_2_pio() helper.

* SWDMA timings are not programmed by atiixp_set_dma_mode() and if SWDMA
  mode is chosen atiixp_dma_host_on() erroneously enables UDMA, just disable
  support for SWDMA modes for now.

* Enable support for MWDMA0 mode.

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NMikael Starvik <starvik@axis.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Always set ->autotune in init_hwif_sis5513(), this means practically
  no change in behavior since PIO was always tuned in ->ide_dma_check
  and >autotune was always set for ->dma_base == 0 case.

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add sis_ata133_get_base() helper function for obtaining the address of
  the drive control registers on chipset_family == ATA_133 chipsets.

* Add three helper functions for programming PIO/MWDMA timings:
  - sis_ata16_program_timings()  (for ATA_16/33/66/100a chipset families)
  - sis_ata100_program_timings() (for ATA_100/133a chipset families)
  - sis_ata133_program_timings() (for ATA_133 chipset family)

  MWDMA timings are taken from datasheets and they match ATA spec.

* Add generic helper function sis_program_timings() and use it in
  ->set_pio_mode and ->set_dma_mode methods (previously the driver
  depended on BIOS to program the correct MWDMA timings).

* Remove redundant !chipset_family check from init_hwif_sis5513()
  (init_chipset_sis5513() guarantees that we will never get here if
   chipset_family cannot be determined).

* SWDMA seems to be unsupported by SiS chipsets (no info about SWDMA in
  datasheets and for SWDMA0 mode timing requirements are impossible to
  fulfill) so remove ->swdma_mask from init_hwif_sis5513() and handling
  of SWDMA modes from sis_set_dma_mode().

* Enable DMA support for chipset_family == ATA_16.

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch adds id strings for Corsair 1GB (identified as Hyperstone Model1)
inside legacy/ide-cs.c.

It also includes some minor whitespace cleanups.
Signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The patch described by the following excerpt from ChangeLog-2.6.22 makes
it impossible to use UDMA on a Tyan S2707 motherboard (SvrWks CSB5):

commit 2d5eaa6d
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date:   Thu May 10 00:01:08 2007 +0200

    ide: rework the code for selecting the best DMA transfer mode (v3)

    ...

This one-line patch against 2.6.23 fixes the problem.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Then we can get rid of ->issue_flush_fn() and all the driver private
implementations of that.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

init_dma_ali15x3() guarantees that hwif->dma_base will never be set for
m5229_revision < 0x20 so remove redundant m5229_revision >= 0x20 check from
init_hwif_common_ali15x3().

While at it remove incorrect comment.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Set hwif->atapi_dma/{ultra,mwdma}_mask and drive->autodma after checking that
->dma_base exists.  If ->dma_base is not set (== PCI BAR4 cannot be reserved)
then DMA hooks shouldn't be initialized or bad things will happen.

OTOH hwif->set_{pio,dma}_mode hooks should be set even if hwif->dma_base == 0.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Set hwif->ide_dma_{check,on} and hwif->autodma to 1 after checking that
->dma_base exists.  If ->dma_base is not set (== PCI BAR4 cannot be reserved)
then DMA hooks shouldn't be initialized or bad things will happen.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Devices which don't set word 93 validation bit should be now handled by
ide-iops.c::ivb_list[] and for debugging purposes cable detection can be
completely overriden with "idex=ata66" parameter.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Need to probe slave device first to make it release PDIAG-
(this is required for correct device side cable detection).

Based on libata commit f31f0cc2.

Thanks to Craig for testing this patch.

Cc: Craig Block <chblock3@yahoo.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Check ide_config_drive_speed() return value.

* While at also call ide_config_drive_speed() if the transfer mode is
  XFER_PIO_SLOW (this case happens iff the transfer mode has already been
  set on the device by ide-proc.c::set_xfer_rate()) and remove redundant
  setting of ->{init,current}_speed.

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>