Firmware uses asynchronized events as a communication method to the
host. The event packets are marked as ETH_P_LINK_CTL protocol type. For
SDIO and PCIe bus, this kind of packets are delivered through virtual
event channel not data channel. This patch adds a screening logic to
make sure the event handler only processes the events coming from the
correct channel.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When p2p connection setup is performed without having ever done an
escan a null pointer exception can occur. This is because the ifp
to abort scanning is taken from escan struct while it was never
initialized. Fix this by using the primary ifp for scan abort. The
abort should still be performed and all scan related commands are
performed on primary ifp.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some nvram files/stores come without the boardrev information,
but firmware requires this to be set. When not found in nvram then
add a default boardrev string to the nvram data.
Reported-by: NRafal Milecki <zajec5@gmail.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer firmwares require the usage of the wowl wakeind struct as size
for the iovar to clear the wake indicators. Older firmwares do not
care, so change the used size.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When the event_msgs iovar is set an array is used to configure the
enabled events. This arrays needs to nulled before configuring
otherwise unhandled events will be enabled. This solves a problem
where in case of wowl the host got woken by an incorrectly enabled
event.
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Adjust AFE before enabling PLL on 8192eu, probably also needed for
8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixup another case where the hard coded register value was used
instead of the name.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set REG_QUEUE_CTRL and REG_ACLK_MON for 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement workaround for LDPC RX hands on 8192eu. This was inspired by
workaround found in the 8192eu vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The vendor driver set register 0xfe58 REG_USB_HWPWM in it's init
sequence for 8192eu. Do the same here.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set HIMR[01] on 8192eu instead of HISR/HIMR. It's not obvious this
really matters for USB devices, but this matches the register writes
performed by the vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set REG_AFE_XTAL_CTRL on 8192eu to the vendor driver value, and do not
skip setting REG_MAX_AGGR_NUM on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu requires clearing/restoring bit 17 in REG_FPGA0_POWER_SAVE
before/after writing RF registers.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu does not use REG_AFE_PLL_CTRL in it's BB init sequence, so
provide device specific handling.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu efuse only has power data for path A and B. It follows the
same layout as 8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Pick PHY init table based on device before distinguishing between
1T/2T/high PA tables. The latter is only currently used for
8188cu/8192cu/8188ru.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu also requires it's own PHY init table.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A device specific AGC table is required for the 8192eu as well.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the required radio init tables for 8192eu devices.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu also has it's own TRXFF boundary value to set.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To match the vendor driver, do not mess with AFE_XTAL_CTRL on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu requires a different MAC init table. Add the missing table
and specify the table to use in the fileops structure.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch prints pcie scratch registers during firmware dump. They
will be useful for analysing firmware status.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch processes sub AMSDU frame received in AP mode.

If a packet is multicast/broadcast, it is sent to kernel/upper
layer as well as queued back to AP TX queue so that it can be
sent to other associated stations.

If a packet is unicast and RA is present in associated station list,
it is again requeued into AP TX queue.

If a packet is unicast and RA is not in associated station list,
packet is forwarded to kernel to handle routing logic.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Bridge packets are enqueued to wmm tx queue, but will not be sent
until main workqeue is scheduled for new interrupt or other
reason. This adds unnecessary delay during traffic.

We will schedule main workqueue when bridge packet is queued.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

skb forwarded to TCP/IP stack doesn't need to allocate in DMA ZONE.
This patch removes GFP_DMA flag in this case to save precious DMA
memory.
Signed-off-by: NXinming Hu <huxm@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some of the chipsets have two revisions. This patch
selects appropriate firmware by checking revision id.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

User can configure wakeup on GTK rekey fail with wowlan.
Added corresponding wakeup reason.
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Added driver functionality to offload GTK rekey to firmware. When
AP sends new GTK, firmware will update it.
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Per the vendor driver, it looks like the 8192eu doesn't have LDOA15 /
LDOV12 registers.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu uses the same H2C API as the 8723bu. Call the correct
functions for update_rate_mask() and report_connect().
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8192eu A/B cut parts were incorrectly identified as 8192cu devices.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With support for more chips being added, use an enum to specify the
chip version.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Improve descriptive names of some registers and add some additional
registers only found on nextgen chips.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8192eu uses the new TX descriptor format
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is no short GI bit in the txdesc40 format.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

txdesc40 dword2 gid is a 6 bit field, not a single bit
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With the size based naming of TX descriptors. Change the bit
definition namings to indicate which descriptor format they match,
rather than having a device name in the bit name.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>