This code snippet is simply writing default values to the register which is
unnecessary since the values are programmed into the register by default.
There is a special case for 80003es2lan needing the Retransmit on Late
Collision bit set but that is also done in e1000_init_hw_80003es2lan().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the default hardware values for TIPG except for 80003es2lan(*).  The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs).  The only change in
functionality is setting the correct default TIPG for the latter devices.

(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When connected to certain switches, the 82579 PHY might drop link
unexpectedly.  Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware erratum workaround where the TXDCTL register must be the same
setting for both queues should always be done.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Prabhakar Kushwaha <prabhakar@freescale.com>, set
appropriate default interrupt mode dependent on whether CONFIG_PCI_MSI
is enabled in the kernel configuration and if the hardware supports
MSI-X.  Set the module parameter log message accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Jin Qing <b24347@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make it more like how igb does it, with some additional error checking.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations.  Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable RPS by default.  Disallow jumbo frames when both receive checksum
and receive hashing are enabled because the hardware cannot do both IP
payload checksum (enabled when receive checksum is enabled when using
packet split which is used for jumbo frames) and provide RSS hash at the
same time.

v2: added ethtool command to query flow hashing behavior per Ben Hutchings
    and changed the type of rsskey to cleanup the setting of the register
    array and avoid unnecessary casts (as pointed out by Joe Perches).
    The long error messages are not changed since there is nothing in
    the kernel ./Documentation that suggests the preferred method for
    dealing with long messages other than to never break strings; leaving
    them as-is for now.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1) cleanup whitespace in e1000_rx_checksum() function header comment
2) do not check hardware checksum when Rx checksum is disabled
3) reduce duplicated calls to le16_to_cpu() by just using it within
   e1000_rx_checksum() instead of in each call to the function

v2: use swab16 instead of le16_to_cpu & htons and corrected type for the
passed-in csum
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSteve Wise <swise@opengridcomputing.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we must provide the IP destination address, and a reference has
to be dropped when we're done with the entry.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some WWAN LTE/3G devices based on chipsets from Qualcomm provide
near standard CDC ECM interfaces in addition to the usual serial
interfaces.   The Huawei E392/E398 are examples of such devices.

These typically cannot be fully configured using AT commands
over a serial interface.  It is necessary to speak the proprietary
Qualcomm MSM Interface (QMI) protocol to the device to enable the
ethernet proxy functionality.

The devices embed the QMI protocol in CDC on the control interface,
using standard CDC commands and notifications. The do not otherwise
use CDC commands for the ethernet function.  This driver does
therefore not need access to any other aspects of the control
interface than the descriptors attached to it.

Another driver, cdc-wdm, will provide userspace access to the
QMI protocol independently of this driver.  To facilitate this,
this driver avoids binding to the control interface, and uses
only the associated data interface after parsing the common CDC
functional descriptors on the control interface.

You will want both the cdc-wdm and option drivers as companions to
this driver, to have full access to all interfaces and protocols
exported by the device.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver adds support for Xilinx 10/100/1000 AXI Ethernet.

It can be used, for instance, on Xilinx boards with a Microblaze
architecture like the ML605.

The patch is against the latest net-next tree and checkpatch clean.
Signed-off-by: NAriane Keller <ariane.keller@tik.ee.ethz.ch>
Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We introduced a new return here but forgot to drop the lock.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use existing helpers to clarify skb headers manipulation.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using module_platform_driver can make the code smaller.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add polling interface to xen-netfront device to support netconsole

This patch also alters the spin_lock usage to use irqsave variant.
Documentation/networking/netdevices.txt states that start_xmit
can be called with interrupts disabled by netconsole and therefore using
the irqsave/restore locking in this function is looks correct.
Signed-off-by: NTina.Yang <tina.yang@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NZhenzhong.Duan <zhenzhong.duan@oracle.com>
Tested-by: Ngurudas.pai <gurudas.pai@oracle.com>
[v1: Copy-n-pasted Ian Campbell comments]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Davem says:

1) Fix JIT code generation on x86-64 for divide by zero, from Eric Dumazet.

2) tg3 header length computation correction from Eric Dumazet.

3) More build and reference counting fixes for socket memory cgroup
   code from Glauber Costa.

4) module.h snuck back into a core header after all the hard work we
   did to remove that, from Paul Gortmaker and Jesper Dangaard Brouer.

5) Fix PHY naming regression and add some new PCI IDs in stmmac, from
   Alessandro Rubini.

6) Netlink message generation fix in new team driver, should only advertise
   the entries that changed during events, from Jiri Pirko.

7) SRIOV VF registration and unregistration fixes, and also add a
   missing PCI ID, from Roopa Prabhu.

8) Fix infinite loop in tx queue flush code of brcmsmac, from Stanislaw Gruszka.

9) ftgmac100/ftmac100 build fix, missing interrupt.h include.

10) Memory leak fix in net/hyperv do_set_mutlicast() handling, from Wei Yongjun.

11) Off by one fix in netem packet scheduler, from Vijay Subramanian.

12) TCP loss detection fix from Yuchung Cheng.

13) TCP reset packet MD5 calculation uses wrong address, fix from Shawn Lu.

14) skge carrier assertion and DMA mapping fixes from Stephen Hemminger.

15) Congestion recovery undo performed at the wrong spot in BIC and CUBIC
    congestion control modules, fix from Neal Cardwell.

16) Ethtool ETHTOOL_GSSET_INFO is unnecessarily restrictive, from Michał Mirosław.

17) Fix triggerable race in ipv6 sysctl handling, from Francesco Ruggeri.

18) Statistics bug fixes in mlx4 from Eugenia Emantayev.

19) rds locking bug fix during info dumps, from your's truly.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
  rds: Make rds_sock_lock BH rather than IRQ safe.
  netprio_cgroup.h: dont include module.h from other includes
  net: flow_dissector.c missing include linux/export.h
  team: send only changed options/ports via netlink
  net/hyperv: fix possible memory leak in do_set_multicast()
  drivers/net: dsa/mv88e6xxx.c files need linux/module.h
  stmmac: added PCI identifiers
  llc: Fix race condition in llc_ui_recvmsg
  stmmac: fix phy naming inconsistency
  dsa: Add reporting of silicon revision for Marvell 88E6123/88E6161/88E6165 switches.
  tg3: fix ipv6 header length computation
  skge: add byte queue limit support
  mv643xx_eth: Add Rx Discard and Rx Overrun statistics
  bnx2x: fix compilation error with SOE in fw_dump
  bnx2x: handle CHIP_REVISION during init_one
  bnx2x: allow user to change ring size in ISCSI SD mode
  bnx2x: fix Big-Endianess in ethtool -t
  bnx2x: fixed ethtool statistics for MF modes
  bnx2x: credit-leakage fixup on vlan_mac_del_all
  macvlan: fix a possible use after free
  ...

We can remove the rt_gateway == 0 check but we shouldn't
remove the 'dst' initialization too.

Noticed by Eric Dumazet.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can remove the rt_gateway == 0 check but we shouldn't
remove the 'dst' initialization too.

Noticed by Eric Dumazet.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It can never actually happen.  rt_gateway is either the fully resolved
flow lookup key's destination address, or the non-zero FIB entry gateway
address.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rds_sock_info() triggers locking warnings because we try to perform a
local_bh_enable() (via sock_i_ino()) while hardware interrupts are
disabled (via taking rds_sock_lock).

There is no reason for rds_sock_lock to be a hardware IRQ disabling
lock, none of these access paths run in hardware interrupt context.

Therefore making it a BH disabling lock is safe and sufficient to
fix this bug.
Reported-by: NKumar Sanghvi <kumaras@chelsio.com>
Reported-by: NJosh Boyer <jwboyer@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A considerable effort was invested in wiping out module.h
from being present in all the other standard includes.  This
one leaked back in, but once again isn't strictly necessary,
so remove it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The file net/core/flow_dissector.c seems to be missing
including linux/export.h.
Signed-off-by: NJesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes event message behaviour to send only updated records
instead of whole list. This fixes bug on which userspace receives non-actual
data in case multiple events occur in row.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

do_set_multicast() may not free the memory malloc in
netvsc_set_multicast_list().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An implicit instance of module.h leaked back into existence
and was masking the fact that these drivers weren't calling
out the include for itself.  Fix the drivers before we remove
the implicit include path via net/netprio_cgroup.h file.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

STM has a device ID within its own VENDOR space, and it is being
used in the STA2X11 I/O Hub.
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a race on sk_receive_queue between llc_ui_recvmsg and
sock_queue_rcv_skb.

Our current solution is to protect skb_eat in llc_ui_recvmsg
with the queue spinlock.
Signed-off-by: NRadu Iliescu <riliescu@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit "db8857bf stmmac: use an unique MDIO bus name" my
device stopped being probed because two different names were being
used in different places. This fixes the inconsistency.
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Florian Fainelli <florian@openwrt.org>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  quota: Pass information that quota is stored in system file to userspace
  ext2: protect inode changes in the SETVERSION and SETFLAGS ioctls
  jbd: Issue cache flush after checkpointing

Commit 5bc75a88 ("kernel-doc: fix new warning in regulator core")
added documentation for of_node to address a warning but the
documentation didn't explain what the parameter is for so would be
likely to be unhelpful for users.  Clarify that.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix silent outputs from docking-station jacks of Dell laptops
  ALSA: HDA: Use model=auto for Thinkpad T510
  ALSA: hda - Fix buffer-alignment regression with Nvidia HDMI
  ALSA: hda - Fix a unused variable warning
  snd-hda-intel: better Alienware M17x R3 quirk
  ALSA: hda/realtek - Remove use_jack_tbl field
  ALSA: hda/realtek - Avoid conflict of unsol-events with static quirks
  ALSA: hda/realtek - Avoid multi-ios conflicting with multi-speakers

GMA500 did it the old way and it's been on the TODO list to fix.
Current kernels now blow up if we use the old way so we'd better
do the work!
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

so move its include into fs.h inside the __KERNEL__ protection.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Power management fixes for 3.3

Two fixes for regressions introduced during the merge window, one fix for
a long-standing obscure issue in the computation of hibernate image size
and two small PM documentation fixes.

* tag 'pm-fixes-for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / Sleep: Fix read_unlock_usermodehelper() call.
  PM / Hibernate: Rewrite unlock_system_sleep() to fix s2disk regression
  PM / Hibernate: Correct additional pages number calculation
  PM / Documentation: Fix minor issue in freezing_of_tasks.txt
  PM / Documentation: Fix spelling mistake in basic-pm-debugging.txt