- 26 1月, 2012 8 次提交
-
-
由 Bruce Allan 提交于
The Tx/Rx head and tail registers and itr_register are always at known addresses based on the __iomem address at which the PCI region (from BAR 0) is mapped and known offsets within the region for each of these registers. Store and use the full address rather than just the region offset to reduce unnecessary address calculations. Also, change current u8 __iomem pointers to void __iomem pointers. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Bruce Allan 提交于
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Bruce Allan 提交于
Enable RPS by default. Disallow jumbo frames when both receive checksum and receive hashing are enabled because the hardware cannot do both IP payload checksum (enabled when receive checksum is enabled when using packet split which is used for jumbo frames) and provide RSS hash at the same time. v2: added ethtool command to query flow hashing behavior per Ben Hutchings and changed the type of rsskey to cleanup the setting of the register array and avoid unnecessary casts (as pointed out by Joe Perches). The long error messages are not changed since there is nothing in the kernel ./Documentation that suggests the preferred method for dealing with long messages other than to never break strings; leaving them as-is for now. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Bruce Allan 提交于
1) cleanup whitespace in e1000_rx_checksum() function header comment 2) do not check hardware checksum when Rx checksum is disabled 3) reduce duplicated calls to le16_to_cpu() by just using it within e1000_rx_checksum() instead of in each call to the function v2: use swab16 instead of le16_to_cpu & htons and corrected type for the passed-in csum Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Bjørn Mork 提交于
Some WWAN LTE/3G devices based on chipsets from Qualcomm provide near standard CDC ECM interfaces in addition to the usual serial interfaces. The Huawei E392/E398 are examples of such devices. These typically cannot be fully configured using AT commands over a serial interface. It is necessary to speak the proprietary Qualcomm MSM Interface (QMI) protocol to the device to enable the ethernet proxy functionality. The devices embed the QMI protocol in CDC on the control interface, using standard CDC commands and notifications. The do not otherwise use CDC commands for the ethernet function. This driver does therefore not need access to any other aspects of the control interface than the descriptors attached to it. Another driver, cdc-wdm, will provide userspace access to the QMI protocol independently of this driver. To facilitate this, this driver avoids binding to the control interface, and uses only the associated data interface after parsing the common CDC functional descriptors on the control interface. You will want both the cdc-wdm and option drivers as companions to this driver, to have full access to all interfaces and protocols exported by the device. Signed-off-by: NBjørn Mork <bjorn@mork.no> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
This driver adds support for Xilinx 10/100/1000 AXI Ethernet. It can be used, for instance, on Xilinx boards with a Microblaze architecture like the ML605. The patch is against the latest net-next tree and checkpatch clean. Signed-off-by: NAriane Keller <ariane.keller@tik.ee.ethz.ch> Signed-off-by: NDaniel Borkmann <daniel.borkmann@tik.ee.ethz.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dan Carpenter 提交于
We introduced a new return here but forgot to drop the lock. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Acked-by: NDmitry Kravkov <dmitry@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Use existing helpers to clarify skb headers manipulation. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 1月, 2012 7 次提交
-
-
由 Fabio Estevam 提交于
Using module_platform_driver can make the code smaller. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Konrad Rzeszutek Wilk 提交于
add polling interface to xen-netfront device to support netconsole This patch also alters the spin_lock usage to use irqsave variant. Documentation/networking/netdevices.txt states that start_xmit can be called with interrupts disabled by netconsole and therefore using the irqsave/restore locking in this function is looks correct. Signed-off-by: NTina.Yang <tina.yang@oracle.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Signed-off-by: NZhenzhong.Duan <zhenzhong.duan@oracle.com> Tested-by: Ngurudas.pai <gurudas.pai@oracle.com> [v1: Copy-n-pasted Ian Campbell comments] Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: NIan Campbell <ian.campbell@citrix.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
This patch changes event message behaviour to send only updated records instead of whole list. This fixes bug on which userspace receives non-actual data in case multiple events occur in row. Signed-off-by: NJiri Pirko <jpirko@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
do_set_multicast() may not free the memory malloc in netvsc_set_multicast_list(). Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com> Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Paul Gortmaker 提交于
An implicit instance of module.h leaked back into existence and was masking the fact that these drivers weren't calling out the include for itself. Fix the drivers before we remove the implicit include path via net/netprio_cgroup.h file. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alessandro Rubini 提交于
STM has a device ID within its own VENDOR space, and it is being used in the STA2X11 I/O Hub. Signed-off-by: NAlessandro Rubini <rubini@gnudd.com> Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com> Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alessandro Rubini 提交于
After commit "db8857bf stmmac: use an unique MDIO bus name" my device stopped being probed because two different names were being used in different places. This fixes the inconsistency. Signed-off-by: NAlessandro Rubini <rubini@gnudd.com> Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Florian Fainelli <florian@openwrt.org> Acked-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 1月, 2012 11 次提交
-
-
由 Chris Healy 提交于
Add reporting of silicon revision during the probe function for Marvell 88E6123/88E6161/88E6165 switches. Signed-off-by: NChris Healy <cphealy@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
tg3_start_xmit() makes the wrong assumption for TSOV6 that skb->head doesnt include any payload data. if (skb_is_gso_v6(skb)) hdr_len = skb_headlen(skb) - ETH_HLEN; This is not true anymore after commit f07d960d (tcp: avoid frag allocation for small frames) We should instead use : skb_transport_offset(skb) + tcp_hdrlen(skb) Its also true for IPv4 Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> CC: Matt Carlson <mcarlson@broadcom.com> CC: Michael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
This also changes the cleanup logic slightly to aggregate completed notifications for multiple packets. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Paulius Zaleckas 提交于
These statistics helped me a lot while searching who is losing packets in my setup. I added these stats to MIB group since they are very similar, but just in other registers. I have tested this patch on 88F6281 SoC. Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ariel Elior 提交于
The macro `CHIP_IS_E1x' requires `bp' to be initialized. As `bp' is not yet initialized during this phase of `bnx2x_init_dev', it accessed uninitialized fields in the struct. Signed-off-by: NAriel Elior <ariele@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dmitry Kravkov 提交于
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dmitry Kravkov 提交于
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Previosuly, in MF modes `ethtool -S' lacked some of the statistics which appeared in non-MF modes. This has been fixed. Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Upon insertion of elements into the execution queue, it is validated that there are enough credits to support additional vlan-macs, and the credits are consumed. However, when removing a pending command in `bnx2x_vland_mac_del_all' the consumed credits are not released, which might cause leakage and eventually the inability to add new vlan-macs in certain scenarios. Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Commit bc416d97 (macvlan: handle fragmented multicast frames) added a possible use after free in macvlan_handle_frame(), since ip_check_defrag() uses pskb_may_pull() : skb header can be reallocated. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Cc: Ben Greear <greearb@candelatech.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 1月, 2012 10 次提交
-
-
由 Randy Dunlap 提交于
Fix new kernel-doc warning: Warning(drivers/net/phy/mdio_bus.c:49): No description found for parameter 'size' Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sathya Perla 提交于
Currently RSS rings are not created in a multi-channel config. RSS rings can be created on one (out of four) interfaces per port in a multi-channel config. Doing this insulates the driver from a FW bug wherin multi-channel config is wrongly reported even when not enabled. This also helps performance in a multi-channel config, as one interface per port gets RSS rings. Signed-off-by: NSathya Perla <sathya.perla@emulex.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Driver should check for mapping errors. Machines with limited DMA maps may return an error when a PCI map is requested (not an issue on standard x86). Also use upper/lower 32 bits macros for clarity. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Skge device would assert carrier (link up) as soon as network device open was called, rather than waiting until PHY has detected link. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marcel Apfelbaum 提交于
Slave async events were mapped to single eq. This patch fixes this issue, so the slaves can map the async events to any eq. Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marcel Apfelbaum 提交于
Num mtts from profile is really the number of mtt segments. Thus, in make profile, to get the proper number of MTT entries, must multiply num_mtts by mtts per segment. Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marcel Apfelbaum 提交于
The Virtual Functions should not be aware their function number. Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eugenia Emantayev 提交于
In native mode display all available staticstics. In SRIOV mode on VF display only SW counters statistics, in SRIOV mode on hypervisor display SW counters and errors (got from FW) statistics. Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eugenia Emantayev 提交于
In multifunction mode - DUMP_STATS command is not executed for VFs. Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eugenia Emantayev 提交于
Bug fix: Not all stats fields were cleared. Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il> Reviewed-by: NYevgeny Petriln <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 1月, 2012 1 次提交
-
-
由 Roopa Prabhu 提交于
reverting back change that access enic->num_vfs outside CONFIG_PCI_IOV Reported-by: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 1月, 2012 3 次提交
-
-
由 Stephen Hemminger 提交于
The arrays of function pointers should be const to make life harder for rootkits. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Tested-by: NSibai Li <sibai.li@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
Fixes sparse warnings: drivers/net/ethernet/intel/ixgbevf/vf.c:418:21: warning: symbol 'ixgbevf_82599_vf_info' was not declared. Should it be static? drivers/net/ethernet/intel/ixgbevf/vf.c:423:21: warning: symbol 'ixgbevf_X540_vf_info' was not declared. Should it be static? drivers/net/ethernet/intel/ixgbevf/mbx.c:331:29: warning: symbol 'ixgbevf_mbx_ops' was not declared. Should it be static? Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Tested-by: NSibai Li <sibai.li@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Tested-by: NSibai Li <sibai.li@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-