* use set_rx_mode to (re)initialize the multicast table.
* MC_FILTERBREAK is 64 (= 8 * 8bit)
* remove local_info_t.mc_filter

without this patch after an rmmod, modprobe the card won't work anymore
until the next reboot.

This patch seem safe to apply for all cards as the bsd driver already do
that.

I had to add a timeout because strange things happen (issuecommand will
fail) if the card is already reseted (after a reboot).

PS : it seems there are missing reset when leaving monitor mode...
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>

If using UDP over VLAN, with the skge driver there is a possibility
of generating an incorrect checksum. This is a unlikely occurrence
because it is only an issue on Yukon revision 0, and that revision
doesn't seem to exist on any current hardware (probably early prototype).
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Power management parameters could not be set by iwconfig due to
incorrect error handling.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Use platform_driver_unregister not driver_unregister to unregister a
struct platform_driver.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

jazz_sonnic_device -> jazz_sonic_device
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Sorry, no sekr1t mips c0dez ;-)
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch fixes graceful stop timeout handling in PPC4xx EMAC driver.

Currently, when we stop TX/RX channels we just do some number of loops
without relying on actual spent time. This has finally bitten me on
one of our systems (heavy network traffic during start up, RX channel
is stopped several times to configure multicast list).

Graceful channel stop can take up to 1 frame time, so I've added
device specific timeout counter which depends on current link speed
and calls to udelay() to really wait required amount of time before
giving up.
Signed-off-by: NEugene Surovegin <ebs@ebshome.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Avoid possible confusion between skge and sk98lin driver by
tagging messages properly.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Add permanent address and link status support via ethtool.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Remove code from sk98lin that does it's own checksum validation.
This code is incorrect when dealing with nested protocols like
VLAN's, and it is better to use regular receive code path to
handle hardware checksum.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Parse outgoing packets in e1000_transfer_dhcp_info as raw packet even if
protocol bits are set.  pump, for instance causes kernel panic on some
systems, if parsed via udp header.

Thanks to Derrell Lipman <Derrell.Lipman@BacklotTech.com> for reporting and
testing.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

The device has not gone through a whole reset/init sequence until the
device is up. Accessing the mii interface before this point is not
safe.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

This patch fixes a problem plaguing Dell notebooks with built-in b44
ethernet: The driver refuses to transmit packets of any kind until after
the first 5-second tx_timeout occurs. This bug causes DHCP negotiation to
fail (timeout) during installation of Ubuntu Linux.
Signed-off-by: NMark Lord <lkml@rtr.ca>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

drivers/net/dgrs.c: In function `dgrs_init_module':
drivers/net/dgrs.c:1598: `dgrs_pci_driver' undeclared (first use in this function)
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

ipw2100: Fix 'Driver using old /proc/net/wireless...' message

Wireless extensions moved the get_wireless_stats handler from being
in net_device into wireless_handler.

A prior instance of this patch resolved the issue for the ipw2200.
This one fixes it for the ipw2100.
Signed-off-by: NBenoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: NJames Ketrenos <jketreno@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change CONFIG_FEC_8XX to depend on CONFIG_8xx instead of CONFIG_FEC.
CONFIG_FEC depends on ColdFire CPUs, which does not apply for the
PPC 8xx processors.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hermas_bap_pread,  hermes_bap_pwrite, and hermes_bap_pwrite_pad all have a parameter "len" that is declared unsigned,
but checked for a value less than zero. Auditing the callers, it is possible for len to be passed a negative value, so len should be an int.

Thanks to LinuxICC (http://linuxicc.sf.net)
Signed-off-by: NGabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

In isl_38xx.c
In routine isl38xx_trigger-device

Move unnecessary udelay/register read.
This is only required when hand-compiling the driver and
setting  VERBOSE > SHOW_ERROR_MESSAGES
Signed-off-by: NRoger While <simrw@sim-basis.de>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This header file patch was missing from the recent SAA9730 patch.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Au1000 ethernet driver references plenty of CONFIG_* symbols.
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

For the four versions of hardware that we (currently) support microcode
download on, the default configuration of our receive interrupt mitigation
microcode was too aggressive, and caused unnecessary delays when pinging,
and low(er) throughput on single connection latency sensitive performance
tests.

This code adds microcode support, and sets the defaults to more reasonable
settings. It also explains the functionality in the code in more detail.
Compile and load tested, shows expected behavior for slight delay of ping
packets (1-2ms) when ucode is loaded, and decent interrupt moderation for
small packets, while maintaining good throughput.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The smc91x driver relies upon register bank 2 being selected whenever
the interrupt handler is called.  This isn't always so, especially if
we have a link change event during PHY configuration.

This results in register bank 0 being selected when the interrupt
handler is called, causing the wrong registers to be read for the
IRQ mask and status.  In turn, this causes us to spin with a
permanently asserted IRQ.

The patch ensures that smc_phy_configure always exits with register
bank 2 selected.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Not only SMC_ACK_INT(IM_TX_EMPTY_INT) in in smc_hardware_send_pkt)
appears to be unnecessary (tested with an SMC91C94 and SMC91C111), but
it seems to trigger spurious interrupts on some machines as well.
Removed.

While at it, let's log any remaining spurious interrupts if any (and
clean usage of the max IRQ loop count value).
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This fixes a slab corruption issue in the ipw2200 driver: it essentially
multiplied the error log number _twice_ by the size of the error element
entry (once explicitly in the code, and once implicitly as part of the
regular pointer arithmetic).

Cc: Henrik Brix Andersen <brix@gentoo.org>
Cc: Bernard Blackham <bernard@blackham.com.au>
Cc: Zilvinas Valinskas <zilvinas@gemtek.lt>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
--

The function ipw_request_direct_scan() should bail out when the device
is down.  This fixes a lockup caused by wpa_supplicant triggering
ipw_request_direct_scan() while the driver was in a middle of a reset
due to firmware errors.

Thanks to Zilvinas Valinskas for reporting the bug and helping me
debug it.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The capabilities of the 8169 can be disabled but it is hardly a reason
to prevent the use the device. The (so far) unusual behavior has been
reported on a MIPS platform by Yoichi Yuasa.
Spotted-by: NYoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

I keep on getting "printk: N messages suppressed" messages.  We need to test
netif_msg_intr() _before_ running printk_ratelimit(), because the latter
updates state.

Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

As we are currently unable to fix the problem with carrier and protocol
state signaling in net core I've to disable netif_carrier_off()
calls used by WAN protocol drivers. The attached patch should make
them working again.

The remaining netif_carrier_*() calls in hdlc_fr.c are fine as they
don't touch the physical device.
Signed-off-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

gcc4 doesn't allow typecasted lvals.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Enablement patch for the new PowerBooks (late 2005 edition).

This enables the ATA controller, Gigabit ethernet and basic AGP setup.
Bluetooth works out-of-the box after running hid2hci.

Still remaining is to get the touchpad to work, the simple change of just
adding the new USB ids isn't enough.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Changed jobs and the Freescale address is no longer valid.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use read/write IO operations rather than in/out, as per other
SA1100 platforms.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As part of the ISO C9x conversion gcc deprecates concatenation with
__FUNCTION__ because __FUNCTION__ is not a preprocessor macro.
Signed-off-by: NClemens Buchacher <drizzd@aon.at>
Signed-off-by: NMaximilian Attems <janitor@sternwelten.at>
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>