Pass irqflags to 8250 driver with platform_data. At least Zoom2 has
IRQF_TRIGGER_RISING requirement for the 8250 GPIO irq.

This patch is dependent on 8250 driver changes getting accepted upstream:
http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=commit;h=7053133124d5cdf207c1168c7a0c582a18e12ea7Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This enables to peek the following data.

$ /debug/iommu/isp# ls
mem             nr_tlb_entries  regs
mmap            pagetable       tlb
$ /debug/iommu/isp# head pagetable
L:      da:      pa:
-----------------------------------------
2: 00001000 8ae4a002
2: 00002000 8e7bb002
2: 00003000 8ae49002
2: 00004000 8ae65002
.....
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The second argument should be the end address, not the
length. Actually there will not be any effect on the behavior of this
driver since flush_cache_vmap() calls flush_cache_all() in the end.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add defconfig file for OMAP2 N800 and N810 devices.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add board file for Nokia N800 and N810 devices. Currently only serial ports,
onenand and spi are configured, more to come later.

Tested on Nokia N800.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For some reason usb-tusb6010.c was't compiled, add it to Makefile and
Kconfig. This is prepraration for upcoming n8x0 support.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for modem device found on Amstrad E3 (Delta) board.

Based on earlier patch by Jonathan McDowell, available at
http://the.earth.li/pub/e3/2.6.19/ams-delta-modem.patch.
Modified after Ladislav Michl's arch/arm/mach-omap1/board-voiceblue.c.

This patch is dependent on 8250 driver changes getting accepted upstream:
http://git.kernel.org/?p=linux/kernel/git/sfr/linux-next.git;a=commit;h=7053133124d5cdf207c1168c7a0c582a18e12ea7Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It is possible for GPIO IRQ lines configured with
falling edge triggering only to get IRQs at the
rising edge upon the exit of offmode. And vice
versa. Prevent such IRQs to arrive by generating
the IRQ obeying the detection scheme.
Signed-off-by: NEero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove left over code for parsing omap boot tags. This is
no longer used.
see commit fc0ef1bfa1353e048e055374a09c75320d22231b
Signed-off-by: NRoger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP tags are deprecrated so drop them.

Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.

Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.)  After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Omap tags are deprecated and remove OMAP_TAG_SERIAL_CONSOLE. Console must be
enabled with the console boot parameter instead.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove ifdefs for io.h
Signed-off-by: NTony Lindgren <tony@atomide.com>

Rename OMAP_MPUIO_BASE to OMAP1_MPUIO_BASE
Signed-off-by: NTony Lindgren <tony@atomide.com>

Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.

Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.

In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: NTony Lindgren <tony@atomide.com>

The root cause is a duplicate section name (.text); is this legal?
[ Amerigo Wang: "AFAIK, yes." ]

However, there's a problem with commit
6d760133 in that if you fail to allocate
a mod->sect_attrs (in this case it's null because of the duplication),
it still gets used without checking in add_notes_attrs()

This should fix it

[ This patch leaves other problems, particularly the sections directory,
  but recent parisc toolchains seem to produce these modules and this
  prevents a crash and is a minimal change -- RR ]
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Tested-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The rarely-used symbol_put_addr() needs to use dereference_function_descriptor
on powerpc.
Reported-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As soon as the framebuffer is registered, our methods may be called by the
kernel. This leads to a crash as xenfb_refresh() gets called before we have
the irq.

Connect to the backend before registering our framebuffer with the kernel.

[ Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=14059 ]
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.infradead.org/users/eparis/notify:
  inotify: Ensure we alwasy write the terminating NULL.
  inotify: fix locking around inotify watching in the idr
  inotify: do not BUG on idr entries at inotify destruction
  inotify: seperate new watch creation updating existing watches

We call lmb_end_of_DRAM() to test whether a DMA mask is ok on a machine
without IOMMU, but this function is marked as __init.

I don't think there's a clean way to get the top of RAM max_pfn doesn't
appear to include highmem or I missed (or we have a bug :-) so for now,
let's just avoid having a broken 2.6.31 by making this function
non-__init and we can revisit later.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: update documentation pointers
  9p: remove unnecessary v9fses->options which duplicates the mount string
  net/9p: insulate the client against an invalid error code sent by a 9p server
  9p: Add missing cast for the error return value in v9fs_get_inode
  9p: Remove redundant inode uid/gid assignment
  9p: Fix possible regressions when ->get_sb fails.
  9p: Fix v9fs show_options
  9p: Fix possible memleak in v9fs_inode_from fid.
  9p: minor comment fixes
  9p: Fix possible inode leak in v9fs_get_inode.
  9p: Check for error in return value of v9fs_fid_add

Add a check in ip_append_data() for NULL *rtp to prevent future bugs in
callers from being exploitable.
Signed-off-by: NJulien Tinnes <julien@cr0.org>
Signed-off-by: NTavis Ormandy <taviso@sdf.lonestar.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kAFS crashes when asked to read a symbolic link because page_getlink()
passes a NULL file pointer to read_mapping_page(), but afs_readpage()
expects a file pointer from which to extract a key.

Modify afs_readpage() to request the appropriate key from the calling
process's keyrings if a file struct is not supplied with one attached.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Before the rewrite copy_event_to_user always wrote a terqminating '\0'
byte to user space after the filename.  Since the rewrite that
terminating byte was skipped if your filename is exactly a multiple of
event_size.  Ouch!

So add one byte to name_size before we round up and use clear_user to
set userspace to zero like /dev/zero does instead of copying the
strange nul_inotify_event.  I can't quite convince myself len_to_zero
will never exceed 16 and even if it doesn't clear_user should be more
efficient and a more accurate reflection of what the code is trying to
do.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NEric Paris <eparis@redhat.com>

The are races around the idr storage of inotify watches.  It's possible
that a watch could be found from sys_inotify_rm_watch() in the idr, but it
could be removed from the idr before that code does it's removal.  Move the
locking and the refcnt'ing so that these have to happen atomically.
Signed-off-by: NEric Paris <eparis@redhat.com>

If an inotify watch is left in the idr when an fsnotify group is destroyed
this will lead to a BUG.  This is not a dangerous situation and really
indicates a programming bug and leak of memory.  This patch changes it to
use a WARN and a printk rather than killing people's boxes.
Signed-off-by: NEric Paris <eparis@redhat.com>

There is nothing known wrong with the inotify watch addition/modification
but this patch seperates the two code paths to make them each easy to
verify as correct.
Signed-off-by: NEric Paris <eparis@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  virtio: net refill on out-of-memory
  smc91x: fix compilation on SMP

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/ps3: Update ps3_defconfig
  powerpc/ps3: Add missing check for PS3 to rtc-ps3 platform device registration

Update ps3_defconfig.

 o Refresh for 2.6.31.
 o Remove MTD support.
 o Add more HID drivers.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

On non-PS3, we get:

| kernel BUG at drivers/rtc/rtc-ps3.c:36!

because the rtc-ps3 platform device is registered unconditionally in a kernel
with builtin support for PS3.
Reported-by: NSachin Sant <sachinp@in.ibm.com>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  IMA: iint put in ima_counts_get and put

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k,m68knommu: Wire up rt_tgsigqueueinfo and perf_counter_open
  m68k: Fix redefinition of pgprot_noncached
  arch/m68k/include/asm/motorola_pgalloc.h: fix kunmap arg
  m68k: cnt reaches -1, not 0
  m68k: count can reach 51, not 50

If we change the inverted attribute to another value, the LED will not be
inverted until we change the GPIO state.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Samuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When setting the same GPIO number, multiple IRQ shared requests will be
done without freing the previous request.  It will also try to free a
failed request or an already freed IRQ if 0 was written to the gpio file.

All these oops and leaks were fixed with the following solution: keep the
previous allocated GPIO (if any) still allocated in case the new request
fails.  The alternative solution would desallocate the previous allocated
GPIO and set gpio as 0.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NSamuel R. C. Vale <srcvale@holoscopio.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This failure is very common on many platforms.  Handling it in the ACPI
processor driver is enough, and we don't need a warning message unless
CONFIG_ACPI_DEBUG is set.

Based on a patch from Zhang Rui.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389Signed-off-by: NFrans Pop <elendil@planet.nl>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the BIOS reports an invalid throttling state (which seems to be
fairly common after system boot), a reset is done to state T0.
Because of a check in acpi_processor_get_throttling_ptc(), the reset
never actually gets executed, which results in the error reoccurring
on every access of for example /proc/acpi/processor/CPU0/throttling.

Add a 'force' option to acpi_processor_set_throttling() to ensure
the reset really takes effect.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389

This patch, together with the next one, fixes a regression introduced in
2.6.30, listed on the regression list. They have been available for 2.5
months now in bugzilla, but have not been picked up, despite various
reminders and without any reason given.

Google shows that numerous people are hitting this issue. The issue is in
itself relatively minor, but the bug in the code is clear.

The patches have been in all my kernels and today testing has shown that
throttling works correctly with the patches applied when the system
overheats (http://bugzilla.kernel.org/show_bug.cgi?id=13918#c14).
Signed-off-by: NFrans Pop <elendil@planet.nl>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Summary:
Kernel panic arise when stack protection is enabled, since strncat will
add a null terminating byte '\0'; So in functions
like this one (wmi_query_block):
        char wc[4]="WC";
	....
	strncat(method, block->object_id, 2);
        ...
the length of wc should be n+1 (wc[5]) or stack protection
fault will arise. This is not noticeable when stack protection is
disabled,but , isn't good either.
Config used: [CONFIG_CC_STACKPROTECTOR_ALL=y,
	      CONFIG_CC_STACKPROTECTOR=y]

Panic Trace
------------
       .... stack-protector: kernel stack corrupted in : fa7b182c
       2.6.30-rc8-obelisco-generic
       call_trace:
           [<c04a6c40>] ? panic+0x45/0xd9
	   [<c012925d>] ? __stack_chk_fail+0x1c/0x40
	   [<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
	   [<fa7b182c>] ? wmi_query_block+0x15a/0x162 [wmi]
	   [<fa7e7000>] ? acer_wmi_init+0x00/0x61a [acer_wmi]
	   [<fa7e7135>] ? acer_wmi_init+0x135/0x61a [acer_wmi]
	   [<c0101159>] ? do_one_initcall+0x50+0x126

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13514Signed-off-by: NCostantino Leandro <lcostantino@gmail.com>
Signed-off-by: NCarlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Jens reported early_ioremap messages with old ASUS board...

> [    1.507461] pci 0000:00:09.0: Firmware left e100 interrupts enabled; disabling
> [    1.532778] early_ioremap(3fffd080, 0000005c) [0] => Pid: 1, comm: swapper Not tainted 2.6.31-rc4 #36
> [    1.561007] Call Trace:
> [    1.568638]  [<c136e48b>] ? printk+0x18/0x1d
> [    1.581734]  [<c15513ff>] __early_ioremap+0x74/0x1e9
> [    1.596898]  [<c15515aa>] early_ioremap+0x1a/0x1c
> [    1.611270]  [<c154a187>] __acpi_map_table+0x18/0x1a
> [    1.626451]  [<c135a7f8>] acpi_os_map_memory+0x1d/0x25
> [    1.642129]  [<c119459c>] acpi_tb_verify_table+0x20/0x49
> [    1.658321]  [<c1193e50>] acpi_get_table_with_size+0x53/0xa1
> [    1.675553]  [<c1193eae>] acpi_get_table+0x10/0x15
> [    1.690192]  [<c155cc19>] acpi_processor_init+0x23/0xab
> [    1.706126]  [<c1001043>] do_one_initcall+0x33/0x180
> [    1.721279]  [<c155cbf6>] ? acpi_processor_init+0x0/0xab
> [    1.737479]  [<c106893a>] ? register_irq_proc+0xaa/0xc0
> [    1.753411]  [<c10689b7>] ? init_irq_proc+0x67/0x80
> [    1.768316]  [<c15405e7>] kernel_init+0x120/0x176
> [    1.782678]  [<c15404c7>] ? kernel_init+0x0/0x176
> [    1.797062]  [<c10038b7>] kernel_thread_helper+0x7/0x10
> [    1.812984] 00000080 + ffe00000

that is rather later.
acpi_gbl_permanent_mmap should be set in acpi_early_init()
if acpi is not disabled

and we have
> [    0.000000] ASUS P2B-DS detected: force use of acpi=ht

just don't load acpi_processor_init...
Reported-and-tested-by: NJens Rosenboom <jens@leia.mcbone.net>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The return value of the get_temp function is not checked when doing a
thermal zone update.  This may lead to a critical shutdown if get_temp
fails and the content of the temp variable is incorrectly set higher than
the critical trip point.

This has been observed on a system with incorrect ACPI implementation
where the corresponding methods were not serialized and therefore
sometimes triggered ACPI errors (AE_ALREADY_EXISTS).  The following
critical shutdowns indicated a temperature of 2097 C, which was obviously
wrong.

The patch adds a return value check that jumps over all trip point
evaluations printing a warning if get_temp fails.  The trip points are
evaluated again on the next polling interval with successful get_temp
execution.
Signed-off-by: NMichael Brunner <mibru@gmx.de>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>