Return the encoder id rather than a boolean.  This is needed
for differentiate between multiple DP bridge chips.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The logic was messy and hard to follow.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

It's handled via external clock.  It should already be protected
by the external ss flag, but add an explicit check just in case.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

v6 of the structure was programmed incorrectly:

  args.v6.ulCrtcPclkFreq.ulPixelClock = cpu_to_le32(clock / 10);

ulPixelClock is a 24-bit bitfield. This statement would thus
do a 32-bit swap of (clock / 10) and drop the top 8 bits which
are ... the LSB. Not what we want. Instead use masks & shifts.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Need to set the external transmitter type properly in
AdjustPixelClock to get the properly output.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Otherwise, no vblank interrupts.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=37522Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

For DP/eDP, always use the standard DP SS indices.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

If the ss clock is external, the CLK_REF bit needs to be set
in the SetPixelClock parameters.  This should fix DP failures
in the channel equalization loop.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

Fusion hardware often has DP to VGA/LVDS/TMDS bridges to
handle non-DP encoders.  Internally we treat them mostly
like DP.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

In DP mode, the DP ref clock can come from PPLL, DCPLL, or ext clock,
depending on the asic.  The crtc virtual pixel clock is derived from
the DP ref clock.

- DCE4: PPLL or ext clock
- DCE5: DCPLL or ext clock

Setting ATOM_PPLL_INVALID will cause SetPixelClock to skip
PPLL/DCPLL programming and only program the DP DTO for the
crtc virtual pixel clock.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- properly mask the ss type
- don't enable ss if type is external or percentage is 0
- if ss enabled and type is external, set ref_div_src to ext clock
- prefer ASIC_INTERNAL_SS_ON_DP to LCD_Info SS_Id for eDP
- fix ss amount calculation
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prefer min m to max p only on pre-r7xx asics.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36197Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prefer minm over maxp.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=35994Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Avoid touching the flip setup regs while
acceleration is running.  Set them at modeset
rather than during pageflip.  Touching these
regs while acceleration is active caused hangs
on pre-avivo chips.  These chips do not seem
to be affected, but better safe than sorry,
plus it avoids repeatedly reprogramming the
regs every flip.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

ntsc seems to work fine with either algo, some
pal TVs seem pickier.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=30832Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Typo in the aspect scale setup.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

... and switch it to container_of upcasting.

v2: converted new pageflip code-paths.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+.  Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.

v2: testing options

v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852
https://bugzilla.kernel.org/show_bug.cgi?id=24462
https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

agd5f: additional cleanups/fixes
Signed-off-by: NCédric Cano <ccano@interfaceconcept.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- set scaler table clears the interleave bit, need to
reset it in encoder quirks, this was already done for
pre-dce4.
- remove the interleave settings from set_base() functions
this is now handled in the encoder quirks functions, and
isn't technically part of the display base setup.
- rename evergreen_do_set_base() to dce4_do_set_base() since
it's used on both evergreen and NI asics.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28182Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

New algo is used for r5xx+ and legacy is used for
r1xx-r4xx, rv515.

I've tested on all relevant GPUs and monitors that I
have access to and have found no problems.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=26562
https://bugzilla.kernel.org/show_bug.cgi?id=26552
May fix:
https://bugs.freedesktop.org/show_bug.cgi?id=32556Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Based on the vbios code.  This should hopefully
fix the pll problems on a number of avivo asics
once it's enabled.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

R6xx+ have per-block swappers.  BE content in the
framebuffer will now be swapped properly during scanout.
Untested, however, the same code is reported working in
the UMS ddx.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@gmail.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed.  Re-program
the mode first, then reset the dpms state.

This fixes the infamous atombios timeouts on resume.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Seems to cause problems on certain laptops

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=24462Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Tested-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The enter argument as implemented by commit 413d45d3 (drm, kdb, kms:
Add an enter argument to mode_set_base_atomic() API) should be more
descriptive as to what it does vs just passing 1 and 0 around.

There is no runtime behavior change as a result of this patch.
Reported-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit f28488c2.

On my rv610 test machine the monitor failed to light up after this.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Some devices such as the radeon chips receive information from user
space which needs to be saved when executing an atomic mode set
operation, else the user space would have to be queried again for the
information.

This patch extends the mode_set_base_atomic() call to pass an argument
to indicate if this is an entry or an exit from an atomic kernel mode
set change.  Individual drm drivers can properly save and restore
state accordingly.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch reworks spread spectrum handling to enable it
properly on lvds and DP/eDP links.  It also fixes several
bugs in the old spread spectrum code.

- Use the ss recommended reference divider if available
when calculating the pll
- Use the proper ss command tables on pre-DCE3 asics
- Avoid reading past the end of the ss info tables
- Enable ss on evergreen asics (lvds, dp, tmds)
- Enable ss on DP/eDP links
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The recent changes to the old algo (prefer high post div)
coupled with the range and precision limitations of using
fixed point with the new algo make the new algo less
useful.  So drop the new algo.  This should work as well
or better than the old new/old combinations and simplifies
the code a lot.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30218
among others.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

These shouldn't be needed with the post div changes
in the last patch.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV620
LVDS panels.  The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30029Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>