According the spec the host should read H_CSR again
after asserting reset H_RST to ensure that reset was
read by the firmware

Cc: stable@vger.kernel.org
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It my take time till ME_RDY will be cleared after the reset,
so we cannot check the bit before we got the interrupt

Cc: stable@vger.kernel.org
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We cleared H_RST for H_CSR on spurious interrupt generated when ME_RDY
while cleared and not while  ME_RDY is set. The spurious interrupt
is not delivered on all platforms in this case the
driver may fail to initialize.

Cc: stable@vger.kernel.org
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

we never freed the mei_clients array on driver shutdown
only on reset
add mei_hbm_reset function that wraps the hbm cleanup
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The pch_phub driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the DT match table to enable DT based probe matching.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

simple_strtoull() is obsolete, use the newer kstrtoull() instead.
Signed-off-by: NSebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix two format string mismatch in genwqe_init_debugfs()
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to the driver descriptions, the atmel_pwm and atmel-ssc
drivers are only useful on Atmel AT32 and AT91 systems. So add
hardware dependencies to these drivers to hide them on other systems.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adding power gating introduced new waiting state for client also during
connection attempt, a connection request can be queued for later either due
device is power gated or due to other on going connection.
We setting client connection state before start of full connect procedure so
in both cased the client state will be MEI_FILE_CONNECTING
which create interlock between the two connection attempts, both
detecting that another connection is in progress.

The interlock is resolved by moving client to connecting state
only upon connection request transmission, so the  first
cb in queue can be processed.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Follow-up for bits missed in
commit 7ca96aa2
mei: make return values consistent across the driver
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fetch FW status registers, as they are important in
in understanding of FW reset reasons
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Communicate hbm version 1.1 to firmware to tell that we
now support power gating isolation protocol
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For non wakeable devices we can't use pci runtime framework
as we are not able to wakeup from D3 states.
Instead we create new pg runtime domain that only drives TXE power
gating protocol to reduce the power consumption.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For non wakeable devices we can't use pci runtime framework
as we are not able to wakeup from D3 states.
Instead we create new pg runtime domain that only drives ME power
gating protocol to reduce the power consumption.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Take rpm token on operation start to initiate rpm resume if needed.
Mark last busy time, release token and advice rpm framework
to try to autosuspend on operation end.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime pm framework for TXE devices.
The runtime pm handlers are used to run
txe power gating isolation protocol.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime pm framework for ME devices.
The runtime pm handlers are used to run
me power gating isolation protocol
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver needs to check whether the write
queue idle before entering power gating
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For power gating entry we write hbm pg entry request command and
then we set pg register
For power gating exit we clear pg register and wait for exit request
hbm command.

Exit power gating request might also be initiated by the firmware
w/o explicit driver request

The power gating state is tracked by pg_state member of me_hw
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since the runtime pm and the internal power gating
cannot be in complete sync in regards to I/O
operations, we need to expose the device
hardware internal power gating state to mei layer

2. We add pg_state handler that translate the hw
internal pg state to mei layer

2. We add power gating event variable to keep
power track of power gating transitions
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Reviewed-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable power gating isolation only if hw and fw support it.
This is indicated by ME_PGIC_HRA bit in ME_CSR_HA register
and on HBM protocol version.

The information is exported to MEI layer through
new pg_is_enabled hw op.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add entry and exit power gating isolation register
write handler.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

LPT devices have internal power gating handled
through registers and hbm calls
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add send message functions and receive dispatch stubs
for power gating isolation hbm protocol.

The protocol consist of requests for entering and exiting
the power gating isolation state and their responses.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Ignore client writing state during cb completion to fix a memory
leak.

When moving cbs to the completion list we should not look at
writing_state as this state can be already overwritten by next
write, the fact that a cb is on the write waiting list means
that it was already written to the HW and we can safely complete it.

Same pays for wait in poll handler, we do not have to check the state
wake is done after completion list processing.

Cc: stable@vger.kernel.org
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

NM and SPS  FW types that may run on ME device on server platforms
do not have valid MEI/HECI interface and driver should not
be bound to it as this might lead to system hung.
In practice not all BIOSes effectively hide such devices from the
OS and in some cases it is not possible.

We determine FW type by examining Host FW status registers in order to
unbind the driver.
In this patch we are adding check for ME on Cougar Point, Lynx Point
Devices

Cc: stable <stable@vger.kernel.org> # 3.10+
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Tested-by: NNikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Increase genwqe driver version number.
Signed-off-by: NFrank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When being used in a multithreaded application there were problems
with memory pages/cachelines accessed by multiple threads/cpus at the
same time, while doing DMA transfers to/from those. To avoid such
situations this fix is creating a copy of the first and the last page
if it is not fully used. The data is copied from user-space into those
pages and results are copied back when the DDCB-request is
successfully finished.
Signed-off-by: NFrank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

rc is not initialized, so genwqe_finish_queue() either returns -EIO or
garbage.  Fortunately the return is not being checked by any callers,
so this has not yet caused any problems. Even so, it makes sense to
fix this small bug in case is is checked in future.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NFrank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Needed to add wmb() before we send the DDCB for execution.
Without the syncronizing it failed on System p.
Signed-off-by: NFrank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In addition to the two flash partitions we used so far, there is a 3rd
one which is enabled for usage by this fix.
Signed-off-by: NFrank Haverkamp <haver@linux.vnet.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

"ret" is zero here so we can remove the "!ret" part of the condition.
"uhdr" is alread a __user pointer so we can remove the cast.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDimitri Sivanich <sivanich@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Using struct pci_device_id is preferred  over
deprecated DEFINE_PCI_DEVICE_TABLE macro
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ERROR: else should follow close brace '}'
+	}
+	else {
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch error
return is not a function, parentheses are not required
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

use cl_dbg for debug log messages in cl context

this also removes checkpatch warning:
quoted string split across lines
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch warining:
Unnecessary space after function pointer name
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Consistently display error on possible copy_from/to_user failures
use dev_dbg  so it cannot be abused to flood the kernel log
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>