The header files could not be build indepdent from each other. This is
happened because headers didn't include the files for things they've used.
This was problematic because the success of a build depended on the
knowledge about the right order of local includes.

Also source files were not including everything they've used explicitly.
Instead they required that transitive includes are always stable. This is
problematic because some transitive includes are not obvious, depend on
config settings and may not be stable in the future.

The order for include blocks are:

 * primary headers (main.h and the *.h file of a *.c file)
 * global linux headers
 * required local headers
 * extra forward declarations for pointers in function/struct declarations

The only exceptions are linux/bitops.h and linux/if_ether.h in packet.h.
This header file is shared with userspace applications like batctl and must
therefore build together with userspace applications. The header
linux/bitops.h is not part of the uapi headers and linux/if_ether.h
conflicts with the musl implementation of netinet/if_ether.h. The
maintainers rejected the use of __KERNEL__ preprocessor checks and thus
these two headers are only in main.h. All files using packet.h first have
to include main.h to work correctly.
Reported-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

With the new interface alternating, the first hop may send packets
in a round robin fashion to it's neighbors because it has multiple
valid routes built by the multi interface optimization. This patch
enables the feature if bonding is selected. Note that unlike the
bonding implemented before, this version is much simpler and may
even enable multi path routing to a certain degree.
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

For the network wide multi interface optimization there are different
routers for each outgoing interface (outgoing from the OGM perspective,
incoming for payload traffic). To reflect this, change the router and
associated data to a list of routers.

While at it, rename batadv_orig_node_get_router() to
batadv_orig_router_get() to follow the new naming scheme.
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Remove bonding and interface alternating code - it will be replaced
by a new, network-wide multi interface optimization which enables
both bonding and interface alternating in a better way.

Keep the sysfs and find router function though, this will be needed
later.
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.

In this way it is easier to update it in case of future
changes.
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>
Signed-off-by: NMarek Lindner <mareklindner@neomailbox.ch>

Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.

Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.

batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().

fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.

BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Reordering the packet type numbers allows us to handle unicast
packets in a general way - even if we don't know the specific packet
type, we can still forward it. There was already code handling
this for a couple of unicast packets, and this is the more
generalized version to do that.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

The goal is to provide the infrastructure for sending, receiving and
parsing information 'containers' while preserving backward
compatibility. TVLV (based on the commonly known Type Length Value
technique) was chosen as the format for those containers. Even if a
node does not know the tvlv type of a certain container it can simply
skip the current container and proceed with the next. Past experience
has shown features evolve over time, so a 'version' field was added
right from the start to allow differentiating between feature
variants - hence the name: T(ype) V(ersion) L(ength) V(alue).

This patch introduces the basic TVLV infrastructure:
 * register / unregister tvlv containers to be sent with each OGM
   (on primary interfaces only)
 * register / unregister callback handlers to be called upon
   finding the corresponding tvlv type in a tvlv buffer
 * unicast tvlv send / receive API calls
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSpyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

batadv_slide_own_bcast_window() is used only in bat_iv_ogm.c
and it is currently touching only batman_iv specific
attributes.

Move it into bat_iv_ogm.c and make it static.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Reported-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

Reported-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: NSven Eckelmann <sven@narfation.org>

batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

The B.A.T.M.A.N. IV OGM receive function still was hard-coded although
it is a routing protocol specific function. This patch takes advantage
of the dynamic packet handler registration to remove the hard-coded
function calls.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The functionality is to be replaced by an improved implementation,
so first clean up.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

In preparation of the upcoming improved routing algorithm the code based has
to be re-organized to allow choosing the routing algorithm at compile time.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

The follow-up routing code changes are going to introduce additional
routing packet types which make this distinction necessary.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

With the current client announcement implementation, in case of roaming,
an update is triggered on the new AP serving the client. At that point
the new information is spread around by means of the OGM broadcasting
mechanism. Until this operations is not executed, no node is able to
correctly route traffic towards the client. This obviously causes packet
drops and introduces a delay in the time needed by the client to recover
its connections.

A new packet type called ROAMING_ADVERTISEMENT is added to account this
issue.

This message is sent in case of roaming from the new AP serving the
client to the old one and will contain the client MAC address. In this
way an out-of-OGM update is immediately committed, so that the old node
can update its global translation table. Traffic reaching this node will
then be redirected to the correct destination utilising the fresher
information. Thus reducing the packet drops and the connection recovery
delay.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

The client announcement mechanism informs every mesh node in the network
of any connected non-mesh client, in order to find the path towards that
client from any given point in the mesh.

The old implementation was based on the simple idea of appending a data
buffer to each OGM containing all the client MAC addresses the node is
serving. All other nodes can populate their global translation tables
(table which links client MAC addresses to node addresses) using this
MAC address buffer and linking it to the node's address contained in the
OGM. A node that wants to contact a client has to lookup the node the
client is connected to and its address in the global translation table.

It is easy to understand that this implementation suffers from several
issues:
 - big overhead (each and every OGM contains the entire list of
   connected clients)
 - high latencies for client route updates due to long OGM trip time and
   OGM losses

The new implementation addresses these issues by appending client
changes (new client joined or a client left) to the OGM instead of
filling it with all the client addresses each time. In this way nodes
can modify their global tables by means of "updates", thus reducing the
overhead within the OGMs.

To keep the entire network in sync each node maintains a translation
table version number (ttvn) and a translation table checksum. These
values are spread with the OGM to allow all the network participants to
determine whether or not they need to update their translation table
information.

When a translation table lookup is performed in order to send a packet
to a client attached to another node, the destination's ttvn is added to
the payload packet. Forwarding nodes can compare the packet's ttvn with
their destination's ttvn (this node could have a fresher information
than the source) and re-route the packet if necessary. This greatly
reduces the packet loss of clients roaming from one AP to the next.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

batman-adv uses pointers which are marked as const and should not
violate that type qualifier by passing it to functions which force a
cast to the non-const version.
Signed-off-by: NSven Eckelmann <sven@narfation.org>

To be coherent, all the functions/variables/constants have been renamed
to the TranslationTable style
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

Signed-off-by: NLinus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

bonding / alternating candidates need to be secured by rcu locks
as well. This patch therefore converts the bonding list
from a plain pointer list to a rcu securable lists and references
the bonding candidates.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

types.h is included by main.h, which is included at the beginning of any
other c-file anyway. Therefore this commit removes those duplicate
inclussions.
Signed-off-by: NLinus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

Signed-off-by: NSven Eckelmann <sven@narfation.org>

Some function parameters are obsolete now and can be removed.
Reported-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing
protocol for multi-hop ad-hoc mesh networks. The networks may be wired or
wireless. See http://www.open-mesh.org/ for more information and user space
tools.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By connecting multiple batman-adv mesh nodes to the same ethernet
segment a loop can be created when the soft-interface is bridged
into that ethernet segment. A simple visualization of the loop
involving the most common case - a LAN as ethernet segment:

node1  <-- LAN  -->  node2
   |                   |
 wifi  <-- mesh -->  wifi

Packets from the LAN (e.g. ARP broadcasts) will circle forever from
node1 or node2 over the mesh back into the LAN.

This patch adds the functionality to detect other batman-adv nodes
connected to the LAN and select a 'gateway' to talk to the
non-batman-adv devices on this LAN. All traffic from and to the mesh
will be handled by this gateway to avoid the loop. OGMs received via
the soft-interface are interpreted as 'port announcements' to locate
potential batman-adv nodes. The patch can also deal with vlans on
top of batX and offers a list of LAN neighbors via debugfs.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

55d1666b521cbed95924c8d4775fe272c103f08c incidentally disabled bonding
of packets first entering the mesh along with also disabling interface
alternating regardless of where the packet came from. This re-enables
these options.
Signed-off-by: NChris Lang <clang@gateworks.com>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes all remaining global variables and includes the
necessary bits into the bat_priv structure. It is the last
remaining piece to allow multiple concurrent mesh clouds on the
same device.
A few global variables have been rendered obsolete during the process
and have been removed entirely.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch replaces the static bat0 interface with a dynamic/abstracted
approach. It is now possible to create multiple batX interfaces by
assigning hard interfaces to them. Each batX interface acts as an
independent mesh network. A soft interface is removed once no hard
interface references it any longer.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch implements a simple layer2 fragmentation to allow traffic
exchange over network interfaces with a MTU smaller than 1500 bytes. The
fragmentation splits the big packets into two parts and marks the frames
accordingly. The receiving end buffers the packets to reassemble the
orignal packet before passing it to the higher layers. This feature
makes it necessary to modify the batman-adv encapsulation for unicast
packets by adding a sequence number, flags and the originator address.
This modifcation is part of a seperate packet type for fragemented
packets to keep the original overhead as low as possible. This patch
enables the feature by default to ensure the data traffic can travel
through the network. But it also prints a warning to notify the user
about the performance implications.

Note: Fragmentation should be avoided at all costs since it has a
dramatic impact on the performance, especially when it comes wifi
networks. Instead of a single packet, 2 packets have to be sent! Not
only valuable airtime is wasted but also packetloss decreases the
throughput. A link with 50% packetloss and fragmentation enabled is
pretty much unusable.
Signed-off-by: NAndreas Langer <an.langer@gmx.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: NSven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>