Bring up-to-date some comments on the location of debug files.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds line feed to printk.
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch removes unused definition and moves code to proper places.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes a parameter (dest) from iwl_fill_beacon_frame() (iwl-agn.c)
 and from iwl3945_fill_beacon_frame(). (iwl-3945.c,iwl-3945.h)
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

    Rate scaling in agn can be broken because of these two problems
    1- the LQ command could not sent, we try to call LQ command before
       post association will be rejected, this will cause the driver to
       break in rs_tx_status reporting initial rate does not match.
    2- In rs_rate_init we can get a value of 12, rate 60, for
       last_txrate_idx, this rate only valid in SISO/MIMO mode only
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.

Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes 4965 from common uCode API structures. Also updates
iwlagn commands with 3945 specific RX command in preparation for 3945 port.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes includes of iwl-helpers.h where not needed
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove clip_groups from priv and related structure.
This code is for 3945 only and was renamed to 4965 in
when code was split.
Also remove unused RATE definitions
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch take care of coming out rfkill when the driver is up while
rfkill is on by restarting interface.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch replaces the current reading EEPROM loop iterations with
iwl_poll_direct_bit(). It also fixes some comment error.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the following build warning when CONFIG_IWLWIFI_DEBUG
is not set.

/work/src/wireless-testing/drivers/net/wireless/iwlwifi/iwl-rx.c:758:
warning: 'iwl_dbg_report_frame' defined but not used
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AP mode operations are seriously affected if mac80211 runs through a
multi-second scan while the AP is trying to send Beacon frames on the
operation channel. While this could be implemented in a way that does
not cause too many problems, it is not very simple and will require
synchronization with Beacon frame scheduling in the drivers (scan one
channel at a time between Beacon frames). Furthermore, such scanning
takes quite a bit longer time and existing userspace applications
would be likely to timeout while waiting for the results.

For now, just refuse requests for new scans (SIOCSIWSCAN) when in AP
mode. In practice, this moves the rejection from iwl* drivers into
mac80211 to make it apply to every mac80211-based driver.

This issue shows up in associated stations getting disconnected when
something (e.g., Network Manager) requests a scan while the interface
is in AP mode. When doing this continuously (e.g., NM does it every 120
seconds), the network gets close to useless.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ability of disabling qos from module params is not required anymore.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ability of disabling qos from module params is not required
anymore.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes second definition of FH_RCSR_CHNL0_RX_CONFIG_SINGLE_FRAME
in iwl-fh.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces personal emails with hopefully
always valid Intel Linux Wireless, which will be routed
to a current maintainer
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds #ifdef CONFIG_IWLWIFI_DEBUG in iwl_rx_reply_rx()
method in iwlwifi/iwl-rx.c) to avoid build error  caused by "iwlwifi:
implement iwl_debug_report_frame for iwlagn".
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patches removes unused variable (pm_state) from iwl-dev.h and
from iwl-3945.h. (wireless-testing tree)
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch protects iwlwifi indirect mmio operations with rmb() and
wmb(). It makes sure CPU reordering won't affect our indirect mmio
access.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch merges implementation of iwl_poll_bit() and
iwl_poll_direct_bit() by letting the latter be a special case of
the former.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes the misue of CSR_GP_CNTRL with CSR_RESET address
in polling the CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY bit in
iwl4965_apm_reset(). This causes "MAC in deep sleep" error sometimes.
The patch also fixes the timeout value and the iwl_poll_bit() return
value check.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes the misuse of microsecond with millisecond in the
polling mechanism of the iwlwifi driver. The impact of this problem
is the unacceptable latency for the whole system (especially during
bringing down the wlan interface).
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch make sure we use only CCK rate for B only network.
For 3945 driver, it sets REPLY_RATE_SCALE command every time
we connect to a new network. In this command we set for every
rate the number of try and next rate. The problem mac80211 reports
same mode for both B and G mode as IEEE80211_BAND_2GHZ which will cause
using invalid rate other than CCK in B only network. THis patch
on association will examine sta valid rate on association, if no
OFDM rate in valid available rates it considers it as B only mode so
we can set REPLY_RATE_SCALE command with valid B only network and only
choose CCK rate in rate scaling.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The old version of this code was copied from 3945 and never updated. This patch
cleans up structs that do not apply and accounts for other changes from
3945->iwlagn (e.g., PHY info can come in a separate cmd response from the
ucode.)
Signed-off-by: NDaniel Halperin <daniel.c.halperin@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch does following things
    1) This patch fixes the a-band association for passive channels with new
    uCode feature that it allows direct scan on passive channels after
    auto-switch from passive to active. This enables sending of direct probes
    on passive channels, as long as some traffic is detected on that channel.
    This improves the scanning for hidden SSIDs in A-band,which is all
    passive channels.

    This patch fixes the bug no 1748.

        http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1748

    2) This fix will only work with uCode version 15.28.2.8 and above.
    Prior versions of uCode would work only if we heard the traffic within
     active dwell time, which is much shorter than passive dwell time and
    is shorter than typical beacon periods. This patch also provids full
    active dwell time even if we hear traffic late in passive dwell.

    3) uCode API version is incremented to 2.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the infrastructure to support older firmware APIs.
The API version number is stored as part of the filename, we first try to
load the most recent firmware and progressively try lower versions.
The API version is also read from the firmware self and stored as part
of the iwl_priv structure. Only firmware that is supported by driver will
be loaded. The version number read from firmware is compared
to supported versions in the driver not the API version used as part of
filename.

An example using this new infrastrucure:
   if (IWL_UCODE_API(priv->ucode_ver) >= 2) {
        Driver interacts with Firmware API version >= 2.
   } else {
        Driver interacts with Firmware API version 1.
   }
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We store the ucode version number as part of
iwl_priv/iwl3945_priv. This enables us to determine
if particular ucode has support for features in order
to have driver support more than one ucode API.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes the misuse of DMA channel number by Tx queue number in
iwl_tx_ctx_stop().

The problem was originally reported by Wu Fengguang who complains
iwlagn driver takes too long time when issuing `ifconfig wlan0 down`.
The patch now decreases the interface bring down time from 2 seconds
to 0.8 second.

This fixes bugs:
http://bugzilla.kernel.org/show_bug.cgi?id=11956
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1790Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Tested-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

3945 rate scaling was broken in recent tree. This patch fix the following:
	1- Get TX response info and update rates window.
	2- Rate scaling selection.
	3- Flush window timer.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add debugfs support to 3945 driver to display rs info.
Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves channels info display from sysfs to debugfs.
This shows channel information as stored in NIC EEPROM. This
is useful in debugging CRDA or iwl goes setting so it belongs
rather to debugfs then to sysfs.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves iwl_enable_interrupts and iwl_disable_interrupts
functions to iwl-core.c
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The find_station routine needs to look at the IWL_AP_ID entry if we're a STA.
Currently, it only looks for STA entries which causes HW crypto to fail.
Signed-off-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch fixes a printk size format error.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves iwl_check_rxon_cmd into iwl-agn-hcmd-check.c
This function compiled out in none debugging or non development
mode and more. We haven't decided which one yet hence preserving the
current 'always compile' state.
More functions will be added to the file namely for checking TX and LQ
commands.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables LO, TXIQ, and BB calibrations for 5150
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for 5150 eeprom versions
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds computation of ct kill threshold
for 5150. Threshold is computed from calibration
data in the EEPROM.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>