Since backlight_types[] isn't modified, let's declare it const.  That
was probably the intention of the author of commit bb7ca747
("backlight: add backlight type"), via which the "const char const *"
construct was introduced.  The duplicate const was detected by sparse.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://neil.brown.name/md:
  md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
  md/raid1,10: Remove use-after-free bug in make_request.
  md/raid10: unify handling of write completion.
  Avoid dereferencing a 'request_queue' after last close.

0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.

Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.

Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).
Reported-by: NPim Zandbergen <P.Zandbergen@macroscoop.nl>
Cc: stable@kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

A single request to RAID1 or RAID10 might result in multiple
requests if there are known bad blocks that need to be avoided.

To detect if we need to submit another write request we test:
 	if (sectors_handled < (bio->bi_size >> 9)) {

However this is after we call **_write_done() so the 'bio' no longer
belongs to us - the writes could have completed and the bio freed.

So move the **_write_done call until after the test against
bio->bi_size.

This addresses https://bugzilla.kernel.org/show_bug.cgi?id=41862Reported-by: NBruno Wolff III <bruno@wolff.to>
Tested-by: NBruno Wolff III <bruno@wolff.to>
Signed-off-by: NNeilBrown <neilb@suse.de>

A write can complete at two different places:
1/ when the last member-device write completes, through
   raid10_end_write_request
2/ in make_request() when we remove the initial bias from ->remaining.

These two should do exactly the same thing and the comment says they
do, but they don't.

So factor the correct code out into a function and call it in both
places.  This makes the code much more similar to RAID1.

The difference is only significant if there is an error, and they
usually take a while, so it is unlikely that there will be an error
already when make_request is completing, so this is unlikely to cause
real problems.
Signed-off-by: NNeilBrown <neilb@suse.de>

On the last close of an 'md' device which as been stopped, the device
is destroyed and in particular the request_queue is freed.  The free
is done in a separate thread so it might happen a short time later.

__blkdev_put calls bdev_inode_switch_bdi *after* ->release has been
called.

Since commit f758eeab
bdev_inode_switch_bdi will dereference the 'old' bdi, which lives
inside a request_queue, to get a spin lock.  This causes the last
close on an md device to sometime take a spin_lock which lives in
freed memory - which results in an oops.

So move the called to bdev_inode_switch_bdi before the call to
->release.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: NWu Fengguang <fengguang.wu@intel.com>
Cc: stable@kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices.  Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode.  Also, make pcie_bus_safe
the default procedure.
Tested-by: NSven Schnelle <svens@stackframe.org>
Tested-by: NSimon Kirby <sim@hostway.ca>
Tested-by: NStephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-and-tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Reported-and-tested-by: NNiels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162Signed-off-by: NJon Mason <mason@myri.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit b03e7495 ("PCI: Set PCI-E Max Payload Size on fabric")
introduced a potential NULL pointer dereference in calls to
pcie_bus_configure_settings due to attempts to access pci_bus self
variables when the self pointer is NULL.

To correct this, verify that the self pointer in pci_bus is non-NULL
before dereferencing it.
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NShyam Iyer <shyam_iyer@dell.com>
Signed-off-by: NJon Mason <mason@myri.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://dev.laptop.org/users/cjb/mmc:
  mmc: sdhci-s3c: Fix mmc card I/O problem
  mmc: sd: UHS-I bus speed should be set last in UHS initialization
  mmc: sdhi: initialise mmc_data->flags before use
  mmc: core: use non-reentrant workqueue for clock gating
  mmc: core: prevent aggressive clock gating racing with ios updates
  mmc: rename mmc_host_clk_{ungate|gate} to mmc_host_clk_{hold|release}
  mmc: sdhci-esdhc-imx: add missing inclusion of linux/module.h

* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
  libceph: fix leak of osd structs during shutdown
  ceph: fix memory leak
  ceph: fix encoding of ino only (not relative) paths
  libceph: fix msgpool

Prior to 2.6.38 automount would not trigger on either stat(2) or
lstat(2) on the automount point.

After 2.6.38, with the introduction of the ->d_automount()
infrastructure, stat(2) and others would start triggering automount
while lstat(2), etc. still would not.  This is a regression and a
userspace ABI change.

Problem originally reported here:

  http://thread.gmane.org/gmane.linux.kernel.autofs/6098

It appears that there was an attempt at fixing various userspace tools
to not trigger the automount.  But since the stat system call is
rather common it is impossible to "fix" all userspace.

This patch reverts the original behavior, which is to not trigger on
stat(2) and other symlink following syscalls.

[ It's not really clear what the right behavior is.  Apparently Solaris
  does the "automount on stat, leave alone on lstat".  And some programs
  can get unhappy when "stat+open+fstat" ends up giving a different
  result from the fstat than from the initial stat.

  But the change in 2.6.38 resulted in problems for some people, so
  we're going back to old behavior.  Maybe we can re-visit this
  discussion at some future date  - Linus ]
Reported-by: NLeonardo Chiquitto <leonardo.lists@gmail.com>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Acked-by: NIan Kent <raven@themaw.net>
Cc: David Howells <dhowells@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine/ste_dma40: fix memory leak due to prepared descriptors
  dmaengine/ste_dma40: fix Oops due to double free of client descriptor
  dmaengine/ste_dma40: remove duplicate call to d40_pool_lli_free().
  dmaengine/ste_dma40: add missing kernel doc for pending_queue

* 'for-linus' of git://opensource.wolfsonmicro.com/regmap:
  regmap: Remove bitrotted module_put()s

* 'for-linus' of git://twin.jikos.cz/jikos/hid:
  HID: wacom: Unregister sysfs attributes on remove
  HID: wacom: Fix error path of power-supply initialization
  HID: add support for HuiJia USB Gamepad connector
  HID: magicmouse: ignore 'ivalid report id' while switching modes, v2
  HID: magicmouse: Set resolution of touch surfaces

* 'for-31-rc5/i2c-fixes' of git://git.fluff.org/bjdooks/linux:
  i2c-tegra: fix possible race condition after tx
  i2c-tegra: add I2C_FUNC_SMBUS_EMUL
  i2c-tegra: Add of_match_table
  i2c-pxa2xx: return proper error code in ce4100_i2c_probe error paths

* 'amd/fixes' of git://git.8bytes.org/scm/iommu:
  iommu/amd: Don't take domain->lock recursivly
  iommu/amd: Make sure iommu->need_sync contains correct value

Fix kernel-doc warning about internal/private data by marking it
as "private:" so that kernel-doc will ignore it.

  Warning(include/linux/regulator/consumer.h:128): No description found for parameter 'ret'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc warning in net/cfg80211.h:

  Warning(include/net/cfg80211.h:1884): No description found for parameter 'registered'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'timers-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
  rtc: twl: Fix registration vs. init order
  rtc: Initialized rtc_time->tm_isdst
  rtc: Fix RTC PIE frequency limit
  rtc: rtc-twl: Remove lockdep related local_irq_enable()
  rtc: rtc-twl: Switch to using threaded irq
  rtc: ep93xx: Fix 'rtc' may be used uninitialized warning
  alarmtimers: Avoid possible denial of service with high freq periodic timers
  alarmtimers: Memset itimerspec passed into alarm_timer_get
  alarmtimers: Avoid possible null pointer traversal

* 'sched-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
  sched: Fix a memory leak in __sdt_free()
  sched: Move blk_schedule_flush_plug() out of __schedule()
  sched: Separate the scheduler entry for preemption

* 'perf-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
  x86, perf: Check that current->mm is alive before getting user callchain
  perf_event: Fix broken calc_timer_values()
  perf events: Fix slow and broken cgroup context switch code

* branch 'linux-next' of git://git.infradead.org/ubifs-2.6:
  UBIFS: not build debug messages with CONFIG_UBIFS_FS_DEBUG disabled

* branch 'linux-next' of git://git.infradead.org/ubi-2.6:
  UBI: do not link debug messages when debugging is disabled

* 'hwmon-for-linus' of git://github.com/groeck/linux:
  hwmon: (ucd9000/ucd9200) Optimize array walk
  hwmon: (max16065) Add chip access warning to documentation
  hwmon: (max16065) Fix current calculation

* 'for-linus' of git://github.com/ericvh/linux:
  fs/9p: Use protocol-defined value for lock/getlock 'type' field.
  fs/9p: Always ask new inode in lookup for cache mode disabled
  fs/9p: Add OS dependent open flags in 9p protocol
  net/9p: Fix kernel crash with msize 512K
  fs/9p: Don't update file type when updating file attributes
  fs/9p: Add fid before dentry instantiation

* 'stable/bug.fixes' of git://oss.oracle.com/git/kwilk/xen:
  xen/smp: Warn user why they keel over - nosmp or noapic and what to use instead.
  xen: x86_32: do not enable iterrupts when returning from exception in interrupt context
  xen: use maximum reservation to limit amount of usable RAM

* 'kvm-updates/3.1' of git://github.com/avikivity/kvm:
  KVM: Fix instruction size issue in pvclock scaling

HID devices can be hotplugged so we should unregister all sysfs attributes when
removing a driver. Otherwise, manually unloading the wacom-driver will not
remove the sysfs attributes. Only when the device is disconnected, they are
removed, eventually.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

power_supply_unregister() must not be called if power_supply_register() failed.
The wdata->psy.dev pointer may point to invalid memory after a failed
power_supply_register() and hence wacom_remove() will fail while calling
power_supply_unregister().

This changes the wacom_probe function to fail if it cannot register the
power_supply devices. If we would want to keep the previous behaviour we had to
keep some flag about the power_supply state and check it on wacom_remove, but
this seems inappropriate here. Hence, we simply fail, too, if
power_supply_register fails.
Signed-off-by: NDavid Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

In tegra_i2c_fill_tx_fifo, once we have finished pushing all the bytes
to the I2C hardware controller, the interrupt might happen before we
have updated i2c_dev->msg_buf_remaining at the end of the function.
Then, in tegra_i2c_isr, we will call again tegra_i2c_fill_tx_fifo
triggering weird behaviour. This has been shown to happen under real
conditions.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NVincent Palatin <vpalatin@chromium.org>
Acked-by: NRhyland Klein <rklein@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch was intended to be part of 7ca2d1a105a239e300b937e9c41a10a4bd08f569
"i2c: Tegra: Add DeviceTree support". However, an early version of that patch,
which was missing a chunk, was applied to next-i2c. This change is that
missing chunk.
Signed-off-by: NJohn Bonesio <bones@secretlab.ca>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Rewrite the loop walking the id array during probe. The new code is
better adapted to a null-terminated array, and is also clearer and
more efficient than the original.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The chips supported by the max16065 driver should not be accessed using direct
i2ctools commands. Add warning to driver documentation to alert users.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>

Current calculation is completely wrong. Add missing brackets to fix it.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 3.0+

Signed-off-by: NJim Garlick <garlick@llnl.gov>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

This make sure we don't end up reusing the unlinked inode object.
The ideal way is to use inode i_generation. But i_generation is
not available in userspace always.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

Some of the flags are OS/arch dependent we add a 9p
protocol value which maps to asm-generic/fcntl.h values in Linux
Based on the original patch from Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>

With msize equal to 512K (PAGE_SIZE * VIRTQUEUE_NUM), we hit multiple
crashes. This patch fix those.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>