The TCP tracking code has a special case that allows to return
NF_REPEAT if we receive a new SYN packet while in TIME_WAIT state.

In this situation, the TCP tracking code destroys the existing
conntrack to start a new clean session.

[DESTROY] tcp      6 src=192.168.0.2 dst=192.168.1.2 sport=38925 dport=8000 src=192.168.1.2 dst=192.168.1.100 sport=8000 dport=38925 [ASSURED]
    [NEW] tcp      6 120 SYN_SENT src=192.168.0.2 dst=192.168.1.2 sport=38925 dport=8000 [UNREPLIED] src=192.168.1.2 dst=192.168.1.100 sport=8000 dport=38925

However, this is a problem for the iptables' CT target event filtering
which will not work in this case since the conntrack template will not
be there for the new session. To fix this, we reassign the conntrack
template to the packet if we return NF_REPEAT.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

For the following rule:

iptables -I PREROUTING -t raw -j CT --ctevents assured

The event delivered looks like the following:

 [UPDATE] tcp      6 src=192.168.0.2 dst=192.168.1.2 sport=37041 dport=80 src=192.168.1.2 dst=192.168.1.100 sport=80 dport=37041 [ASSURED]

Note that the TCP protocol state is not included. For that reason
the CT event filtering is not very useful for conntrackd.

To resolve this issue, instead of conditionally setting the CT events
bits based on the ctmask, we always set them and perform the filtering
in the late stage, just before the delivery.

Thus, the event delivered looks like the following:

 [UPDATE] tcp      6 432000 ESTABLISHED src=192.168.0.2 dst=192.168.1.2 sport=37041 dport=80 src=192.168.1.2 dst=192.168.1.100 sport=80 dport=37041 [ASSURED]
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

In 135367b8 "netfilter: xtables: change xt_target.checkentry return type",
the type returned by checkentry was changed from boolean to int, but the
return values where not adjusted.

arptables: Input/output error

This broke arptables with the mangle target since it returns true
under success, which is interpreted by xtables as >0, thus
returning EIO.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

iprange_ipv6_sub was substracting 2 unsigned ints and then casting
the result to int to find out whether they are lt, eq or gt each
other, this doesn't work if the full 32 bits of each part
can be used in IPv6 addresses. Patch should remedy that without
significant performance penalties. Also number of ntohl
calls can be reduced this way (Jozsef Kadlecsik).
Signed-off-by: NThomas Jacob <jacob@internet24.de>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

In 13ee6ac5 netfilter: fix race in conntrack between dump_table and
destroy, we recovered spinlocks to protect the dump of the conntrack
table according to reports from Stephen and acknowledgments on the
issue from Eric.

In that patch, the refcount bump that allows to keep a reference
to the current ct object was removed. However, we still decrement
the refcount for that object in the output path of
ctnetlink_dump_table():

        if (last)
                nf_ct_put(last)

Cc: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Recently reported oops:

kernel BUG at net/core/skbuff.c:813!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/devices/virtual/net/bond0/broadcast
CPU 8
Modules linked in: sit tunnel4 cpufreq_ondemand acpi_cpufreq freq_table bonding
ipv6 dm_mirror dm_region_hash dm_log cdc_ether usbnet mii serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma i7core_edac edac_core bnx2
ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas dm_mod [last unloaded: microcode]

Modules linked in: sit tunnel4 cpufreq_ondemand acpi_cpufreq freq_table bonding
ipv6 dm_mirror dm_region_hash dm_log cdc_ether usbnet mii serio_raw i2c_i801
i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma i7core_edac edac_core bnx2
ixgbe dca mdio sg ext4 mbcache jbd2 sd_mod crc_t10dif mptsas mptscsih mptbase
scsi_transport_sas dm_mod [last unloaded: microcode]
Pid: 0, comm: swapper Not tainted 2.6.32-71.el6.x86_64 #1 BladeCenter HS22
-[7870AC1]-
RIP: 0010:[<ffffffff81405b16>]  [<ffffffff81405b16>]
pskb_expand_head+0x36/0x1e0
RSP: 0018:ffff880028303b70  EFLAGS: 00010202
RAX: 0000000000000002 RBX: ffff880c6458ec80 RCX: 0000000000000020
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880c6458ec80
RBP: ffff880028303bc0 R08: ffffffff818a6180 R09: ffff880c6458ed64
R10: ffff880c622b36c0 R11: 0000000000000400 R12: 0000000000000000
R13: 0000000000000180 R14: ffff880c622b3000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff880028300000(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000038653452a4 CR3: 0000000001001000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process swapper (pid: 0, threadinfo ffff8806649c2000, task ffff880c64f16ab0)
Stack:
 ffff880028303bc0 ffffffff8104fff9 000000000000001c 0000000100000000
<0> ffff880000047d80 ffff880c6458ec80 000000000000001c ffff880c6223da00
<0> ffff880c622b3000 0000000000000000 ffff880028303c10 ffffffff81407f7a
Call Trace:
<IRQ>
 [<ffffffff8104fff9>] ? __wake_up_common+0x59/0x90
 [<ffffffff81407f7a>] __pskb_pull_tail+0x2aa/0x360
 [<ffffffffa0244530>] bond_arp_rcv+0x2c0/0x2e0 [bonding]
 [<ffffffff814a0857>] ? packet_rcv+0x377/0x440
 [<ffffffff8140f21b>] netif_receive_skb+0x2db/0x670
 [<ffffffff8140f788>] napi_skb_finish+0x58/0x70
 [<ffffffff8140fc89>] napi_gro_receive+0x39/0x50
 [<ffffffffa01286eb>] ixgbe_clean_rx_irq+0x35b/0x900 [ixgbe]
 [<ffffffffa01290f6>] ixgbe_clean_rxtx_many+0x136/0x240 [ixgbe]
 [<ffffffff8140fe53>] net_rx_action+0x103/0x210
 [<ffffffff81073bd7>] __do_softirq+0xb7/0x1e0
 [<ffffffff810d8740>] ? handle_IRQ_event+0x60/0x170
 [<ffffffff810142cc>] call_softirq+0x1c/0x30
 [<ffffffff81015f35>] do_softirq+0x65/0xa0
 [<ffffffff810739d5>] irq_exit+0x85/0x90
 [<ffffffff814cf915>] do_IRQ+0x75/0xf0
 [<ffffffff81013ad3>] ret_from_intr+0x0/0x11
 <EOI>
 [<ffffffff8101bc01>] ? mwait_idle+0x71/0xd0
 [<ffffffff814cd80a>] ? atomic_notifier_call_chain+0x1a/0x20
 [<ffffffff81011e96>] cpu_idle+0xb6/0x110
 [<ffffffff814c17c8>] start_secondary+0x1fc/0x23f

Resulted from bonding driver registering packet handlers via dev_add_pack and
then trying to call pskb_may_pull. If another packet handler (like for AF_PACKET
sockets) gets called first, the delivered skb will have a user count > 1, which
causes pskb_may_pull to BUG halt when it does its skb_shared check.  Fix this by
calling skb_share_check prior to the may_pull call sites in the bonding driver
to clone the skb when needed.  Tested by myself and the reported successfully.

Signed-off-by: Neil Horman
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently tools like ip and ifconfig report incorrect state for cxgb4
interfaces that are up but do not have link and do so until first link
establishment.  This is because the initial netif_carrier_off call is
before register_netdev and it needs to be after to be fully effective.
Fix this by moving netif_carrier_off into .ndo_open.
Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The option name of Delayed SACK Timer should be SCTP_DELAYED_SACK,
not SCTP_DELAYED_ACK.

Left SCTP_DELAYED_ACK be concomitant with SCTP_DELAYED_SACK,
for making compatibility with existing applications.

Reference:
8.1.19.  Get or Set Delayed SACK Timer (SCTP_DELAYED_SACK)
（http://tools.ietf.org/html/draft-ietf-tsvwg-sctpsocket-25)
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Acked-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Acked-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 03634668 (net offloading: Convert checksums to use
centrally computed features.) mistakenly swapped can_checksum_protocol()
arguments.

This broke IPv6 on bnx2 for instance, on NIC without TCPv6 checksum
offloads.
Reported-by: NHans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 0ab03c2b.

It breaks several things including the avahi daemon.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just stumbled upon the issue while looking for another bug.

The code looks correct, the indentation is not.
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sh_irda can not use RX/TX in same time,
but this driver didn't return to RX mode when TX error occurred.
This patch care xmit error case to solve this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In netif_skb_features() we return only the features that are valid for vlans
if we have a vlan packet.  However, we should not mask out NETIF_F_HW_VLAN_TX
since it enables transmission of vlan tags and is obviously valid.
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- tx_fixup() can be called from either timer callback or from xmit()
  in usbnet, so spinlock is added to avoid concurrency-related problem.
- minor correction due to checkpatch warning for some line over 80
  chars after previous patch was applied.
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In drivers/net/ns83820.c::ns83820_init_one() we dynamically allocate
memory via alloc_etherdev(). We then call PRIV() on the returned storage
which is 'return netdev_priv()'. netdev_priv() takes the pointer it is
passed and adds 'ALIGN(sizeof(struct net_device), NETDEV_ALIGN)' to it and
returns it. Then we test the resulting pointer for NULL, which it is
unlikely to be at this point, and later dereference it. This will go bad
if alloc_etherdev() actually returned NULL.

This patch reworks the code slightly so that we test for a NULL pointer
(and return -ENOMEM) directly after calling alloc_etherdev().
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a network namespace is created (via CLONE_NEWNET), the loopback
interface is automatically added to the new namespace, triggering a
printk in ipv6_add_dev() if CONFIG_IPV6_PRIVACY is set.

This is problematic for applications which use CLONE_NEWNET as
part of a sandbox, like Chromium's suid sandbox or recent versions of
vsftpd. On a busy machine, it can lead to thousands of useless
"lo: Disabled Privacy Extensions" messages appearing in dmesg.

It's easy enough to check the status of privacy extensions via the
use_tempaddr sysctl, so just removing the printk seems like the most
sensible solution.
Signed-off-by: NRomain Francoise <romain@orebokech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update bnx2x version to 1.62.00-4
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix AER settings for BCM57712 to allow accessing all device addresses range in CL45 MDC/MDIO
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix BCM84823 LED behavior which may show on some systems
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device may show incorrect duplex mode for devices with external PHY
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve microcode loading verification before proceeding to next stage
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LED on BCM57712+BCM8727 systems requires different settings
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Common init used to be called by the driver when the first port comes up, mainly to reset and reload external PHY microcode.
However, in case management driver is active on the other port, traffic would halted. So limit the common init to be done only once after POR.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable controlling BCM8073 PN polarity swap through nvm configuration, which is required in certain systems
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_reset must be called with sc->lock.  Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.

In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).

Cc: stable@kernel.org
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.

Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case of single tx and rx queues, three MSI-x vectors are allocated instead
of two. This patch fixes that.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Access to cmd register is racey, especially in smp environments. Protect
it using a spinlock.
Signed-off-by: NMatthieu Bucchianeri <matthieu@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a small possibility of a race where the suspend routine gets
called, while a napi callback is still pending and when that comes up,
it enables interrupts which just got disabled in the suspend routine.
This change adds napi disable call in suspend and enable in resume to
avoid race.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Show per-queue stats in ethtool -S output for vmxnet3 interface. Register dump
of ethtool should dump registers for all tx and rx queues.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a performance enhancement fix. vmxnet3 device performs better when
provided with at least 54 bytes (ethernet 14 + IP 20+ TCP 20) in the first SG
buffer. For UDP packets driver provides lesser than that in first sg. This
change fixes the same. Also avoid the redundant pskb_may_pull() call.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make hw vlan tag stripping as enabled by default. Thereby remove
the code to conditionally enable it later.
Signed-off-by: NGuolin Yang <gyang@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While activating the device get it's MAC address from netdev. This will allow
the MAC address configured using ifconfig to persist through the reset.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a bug while changing ring size when MTU is changed.
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: NDmitry Torokhov <dtor@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original code we check if (servl == NULL) twice.  The first time
should print the message that cfmuxl_remove_uplayer() failed and set
"ret" correctly, but instead it just returns success.  The second check
should be checking the value of "ret" instead of "servl".
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the CAN socket code conform to the manpage of sendmsg.
Signed-off-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>