Implement new 32-bit Firmware Port Capabilities in order to
handle new speeds which couldn't be represented in the old 16-bit
Firmware Port Capabilities values.

Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The byte offset of counter descriptors should be stored in size_t variable
instead of an integer.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix checkpatch errors:
CHECK:PREFER_KERNEL_TYPES: Prefer kernel type 'u32' over 'uint32_t'
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To fix these checkpatch complaints:

WARNING: Comparisons should place the constant on the right side of the test
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To fix these checkpatch complaints:

CHECK: Please don't use multiple blank lines
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To fix these checkpatch complaints:

WARNING: suspect code indent for conditional statements (8, 24)
+       if (eth_proto & (MLX5E_PROT_MASK(MLX5E_10GBASE_SR)
[...]
+                       return PORT_FIBRE;
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To fix these checkpatch complaints:

WARNING: Missing a blank line after declarations
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To fix these checkpatch complaints:

CHECK: Blank lines aren't necessary after an open brace '{'
CHECK: Blank lines aren't necessary before a close brace '}'
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add outbound_pci_buffer_overflow to ethtool output for monitoring the
number of packets that were dropped due to lack of PCIe buffers on
receive path from NIC port toward the host(s).

This counter is valid only in case that tx_overflow_buffer_pkt is
supported in MCAM enhanced features.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

rx_buffer_passed_thres_phy - The number of events where the port RX
buffer has passed a fullness threshold.

rx_buffer_full_phy - The number of events where the port RX buffer has
reached 100% fullness.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

outbound_pci_stalled_rd - The percentage of time within the last second
that the NIC had outbound non-posted read requests but could not perform
the operation due to insufficient non-posted credits.

outbound_pci_stalled_wr - The percentage of time within the
last second that the NIC had outbound posted writes requests but could
not perform the operation due to insufficient posted credits.

outbound_pci_stalled_rd_events - The number of events where
outbound_pci_stalled_rd was above the threshold.

outbound_pci_stalled_wr_events - The number of events where
outbound_pci_stalled_wr was above the threshold.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add support for "ethtool DEVNAME" over ipoib ports,
Display standard port information for IPoIB netdevices using ethtool
For example:
$ ethtool ib2
> Settings for ib2:
        Supported ports: [ ]
        Supported link modes:   Not reported
        Supported pause frame use: No
        Supports auto-negotiation: No
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Speed: 100000Mb/s
        Duplex: Full
        Port: Other
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: off
        Link detected: yes
Signed-off-by: NShalom Lagziel <shaloml@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Printing an enhanced IPoIB device information using
"ethtool -i DEVNAME", prints the low level driver name: mlx5_core.
This commit changes the name to mlx5_core [ib_ipoib], to include the
ipoib device driver infromation.

Fixes: 076b0936 ("net/mlx5e: IPoIB, Add ethtool support")
Signed-off-by: NFeras Daoud <ferasda@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Upon interface up/down, driver will send PAOS (Ports Administrative and
Operational Status Register) in order to inform the Firmware on the
desired status of the port by the driver.

Since now we might change physical link status on mlx5e_open/close,
logical VF representor should not use mlx5e_open/close ndos as is, and
should call the logical version mlx5e_open/closed_locked.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Trivial fix to spelling mistake in a netdev_info message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trival fix to spelling mistakes:

firware -> firmware
invald -> invalid
mutilcast -> multicast
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eisa_device_id are not supposed to change at runtime. All functions
working with eisa_device_id provided by <linux/eisa.h> work with
const eisa_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eisa_device_id are not supposed to change at runtime. All functions
working with eisa_device_id provided by <linux/eisa.h> work with
const eisa_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eisa_device_id are not supposed to change at runtime. All functions
working with eisa_device_id provided by <linux/eisa.h> work with
const eisa_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

eisa_device_id are not supposed to change at runtime. All functions
working with eisa_device_id provided by <linux/eisa.h> work with
const eisa_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were reusing skb pointer when reading page frag, since ring
entries contain a union of a skb and frag pointer.  This can
be confusing to people reading the code.  Refactor the code
to read frag pointer directly.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Data and control vNICs currently use the same area name and
error message.  This could lead to confusion.  Make sure
the error message says "ctrl" in case of control and the
data area is called "nfp.bar0".
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Representors may be associated with both VFs or more importantly
with physical ports.  Allow vNIC and MAC statistics to be read
with ethtool -S on representors.  In case of vNICs we reuse
the vNIC statistic helper, we just need to swap RX and TX to
give statistics the "switch perspective."
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the statistics handling code by keeping pointer to vNIC's
config memory in nfp_port.  Note that this is referring to the
representor side of vNICs, vNIC side has the pointer in nfp_net.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add reporting of MAC statistics in ethtool.  MAC statistics
are read out from the MAC IP and accumulated by application
FW, therefore their presence depends on the application FW.

Add missing defines and string names for the statistics and
dump them in ethtool -S.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store pointer to device memory containing MAC statistics
in nfp_port.  This simplifies representor code and will
be used to dump those statistics in ethtool as well.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for reporting vNIC HW stats on representors
split handling of the SW and HW stats in ethtool -S.
Representors don't have SW stats (since vNIC is assigned
to the VM).

Remove the questionable defines which assume nn variable
exists in the scope.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper for printing ethtool strings and advancing the
pointer correctly.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have been recently called out as a bad example for reporting
standard netdev statistics as part of ethtool.  Fix that :)

Removing standard statistics allows us to simplify the structure
holding definitions since we no longer have to mux different types
of statistics.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Users should be able to dump the management FW logs on any
of the driver's netdevs.  Make the code only depend on the
nfp_app and share it between vNICs and representors.

Storing the dump flag is simply dropped for now, since we
only support the argument being set to 0.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend representors' ethtool ops to show basic info like firmware
version, driver version, and driver name.

While at it don't set drvinfo.n_stats and drvinfo.regdump_len,
core will invoke appropriate handlers to get those.

A helper is added to turn a netdev into nfp_app for convenience.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Start linking ethtool ops to representors.  Begin by adding
a separate ops structure and providing link state.  Next
patches will convert appropriate functions to only use nfp_port,
which will make them reusable on representors.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some additional statistics for tracking VXLAN packets and checksum
errors.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware has the capability to perform checksum offload support
(both Tx and Rx) and TSO support for VXLAN packets. Add the support
required to enable this.

The hardware can only support a single VXLAN port for offload. If more
than one VXLAN port is added then the offload capabilities have to be
disabled and can no longer be advertised.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert from using the old u32 supported, advertising, etc. link settings
to the new link mode settings that support bit positions / settings
greater than 32 bits.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add per queue Tx and Rx packet and byte counts.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the dynamic debug support to output information about the hardware
features reported by the device.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently whenever the driver needs to enable or disable interrupts for
a DMA channel it reads the interrupt enable register (IER), updates the
value and then writes the new value back to the IER. Since the hardware
does not change the IER, software can track this value and elimiate the
need to read it each time.

Add the IER value to the channel related data structure and use that as
the base for enabling and disabling interrupts, thus removing the need
for the MMIO read.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add some additional dynamic debug message to the driver. The new messages
will provide additional information about the PCS window calculation.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many of the names used by the driver are based upon the name of the device
found during device probe.  Move the formatting of the names into the
device open function so that any renaming that occurs before the device is
brought up will be accounted for.  This also means moving the creation of
some named workqueues into the device open path.

Add support to register for net events so that if a device is renamed
the corresponding debugfs directory can be renamed.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>