When a device fails, we must not allow an further writes to the array until
the device failure has been recorded in array metadata.  When metadata is
managed externally, this requires some synchronisation...

Allow/require userspace to explicitly remove failed devices from active
service in the array by writing 'none' to the 'slot' attribute.  If this
reduces the number of failed devices to 0, the write block will automatically
be lowered.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Add a state flag 'external' to indicate that the metadata is managed
  externally (by user-space) so important changes need to be
  left of user-space to handle.
  Alternates are non-persistant ('none') where there is no stable metadata -
  after the  array is stopped there is no record of it's status - and
  internal which can be version 0.90 or version 1.x
  These are selected by writing to the 'metadata' attribute.

- move the updating of superblocks (sync_sbs) to after we have checked if
  there are any superblocks or not.

- New array state 'write_pending'.  This means that the metadata records
  the array as 'clean', but a write has been requested, so the metadata has
  to be updated to record a 'dirty' array before the write can continue.
  This change is reported to md by writing 'active' to the array_state
  attribute.

- tidy up marking of sb_dirty:
   - don't set sb_dirty when resync finishes as md_check_recovery
     calls md_update_sb when the sync thread finishes anyway.
   - Don't set sb_dirty in multipath_run as the array might not be dirty.
   - don't mark superblock dirty when switching to 'clean' if there
     is no internal superblock (if external, userspace can choose to
     update the superblock whenever it chooses to).
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently an md array with a write-intent bitmap does not updated that bitmap
to reflect successful partial resync.  Rather the entire bitmap is updated
when the resync completes.

This is because there is no guarentee that resync requests will complete in
order, and tracking each request individually is unnecessarily burdensome.

However there is value in regularly updating the bitmap, so add code to
periodically pause while all pending sync requests complete, then update the
bitmap.  Doing this only every few seconds (the same as the bitmap update
time) does not notciably affect resync performance.

[snitzer@gmail.com: export bitmap_cond_end_sync]
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: "Mike Snitzer" <snitzer@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Clean up the coding style in raid6test/test.c.  Break it apart into
subfunctions to make the code more readable.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make both mktables.c and its output CodingStyle compliant.  Update the
copyright notice.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NOliver Pinter <oliver.pntr@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current attr_fgcol_ec / attr_bgcol_ec macros do a simple shift of bits
to get the color from vc_video_erase_char.  For a monochrome display
however the attribute does not contain any color, only attribute bits.
Furthermore the reverse bit is lost because it is shifted out, the
resulting color is always 0.

This can bee seen on a monochrome console either directly or by setting it
to inverse mode via "setterm -inversescreen on" .  Text is written with
correct color, fb_fillrects from a bit_clear / bit_clear_margins will get
wrong colors.
Signed-off-by: NThomas Pfaff <tpfaff@pcs.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ensure that the default display parameter passed in via the
device's platform data is valid. It turns out when mach-bast.c
was updated, the default_display was set outside of the display
array bounds, causing a panic on startup.

If the default_display is bigger than num_displays, then generate
an error and refuse to initialise the driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change the initial pattern in the s3c2410 framebuffer driver
to black.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update the debugging in the s3c2410 framebuffer driver.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the S3C2412 to the S3C2410 frame buffer driver
by ensuring that any moved registers can be dealt with.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the console suspend to before we save the state of
the framebuffer to ensure that it does not try and change
the fb state again once we have copied it out.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix garbled letters on big endian machines with acceleration enabled.

This makes pm2fb works fine with full acceleration on sparc machine (card
known as Sun PGX-32 or TechSource Raptor GFX-8P).
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix modedb typos
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

cleanup sweep:
  - Kill ps3fb_priv.xdr_ea and ps3fb_priv.xdr_size, use info->screen_base and
    info->fix.smem_len instead.
  - Kill superfluous assignments to info->fix.smem_start, info->fix.smem_len,
    and info->screen_base in ps3fb_set_par(). Their values never change.
  - Add sparse annotations to casts to kill address space warnings
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Round up arbitrary video modes until they fit (if possible)
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reorganize modedb handling:
  - Reorder the video modes in ps3fb_modedb, for easier indexing using
    PS3AV_MODE_* numbers,
  - Introduce ps3fb_native_vmode(), to convert from native (PS3AV_MODE_*) mode
    numbers to struct fb_videomode *,
  - Rename and move ps3fb_default_mode() to ps3fb_vmode().
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow all video modes where the visible resolution plus the black borders
matches a native resolution
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Frame buffer offsets don't have to be `unsigned long', `unsigned int' is
sufficient
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kill ps3fb_res[], as all information it contains can be obtained in some other
way.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Open-code the X_OFF(), Y_OFF(), WIDTH(), HEIGHT(), and VP_OFF() macros, as
they're used in one place only
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kill PS3FB_FULL_MODE_BIT, use PS3AV_MODE_FULL instead
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use symbolic names for video modes
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ps3av_get_scanmode() and ps3av_get_refresh_rate() are unused, so remove them
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller.  It's controlled by "contrast" registers though.

This patch lets boards declare that they have that kind of backlight
control.  The driver can then export this control, letting screenblank and
other operations actually take effect ...  reducing the typically
substantial power drain from the backlight.

Note that it's not fully cooked
  - doesn't force backlight off during system suspend
  - the "power" and "blank" events may not be done right
This should be easily added in the future.

[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Avoid displaying garbage on unused framebuffers.  For most users a single
framebuffer is used together with fbcon.  sm501fb supports two framebuffers
where one often is assigned to fbcon and the other one is left unused during
the boot.

The problem here is that framebuffers not in use by fbcon happen to display
garbage.  This can easily be solved by making sure that framebuffer memory and
palette ram are cleared.

The problem can be observed by using looking at the panel output (fb1) after
booting the kernel with fbcon on crt (fb0).  This is the default
configuration.  It's also possible to watch the garbage on the crt framebuffer
by passing "fbcon=map:1" on the kernel cmdline.  This will assign fbcon to the
panel (fb1) and leave the crt (fb0) unused.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch makes it possible to control panel pins usage with flags passed
from the platform data.  Without this patch the sm501fb driver always controls
the VBIASEN and FPEN pins.  The polarity and use of these pins are very
platform specific, so this patch introduces the flags
SM501FB_FLAG_PANEL_USE_VBIASEN and SM501FB_FLAG_PANEL_USE_FPEN which enable
the use of these pins.

This patch is needed to support the a Sharp LQ104V1DG21 lcd panel on SuperH
platforms such as R2D-1 and R2D-PLUS boards.  Letting the sm501fb driver
control the FPEN and VBIASEN pins like today just results in lcd panel
flicker.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

pci_get_device does a pci_dev_get, so pci_dev_put needs to be called in an
error case

The problem was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@exists@
type T1,T2;
identifier E;
statement S,S1;
expression x1,x2,x3;
expression test;
int ret != 0;
@@

  struct pci_dev *E;
  ...
(
  E = \(pci_get_slot\|pci_get_device\|pci_get_bus_and_slot\)(...);
  if (E == NULL) S
|
  if ((E = \(pci_get_slot\|pci_get_device\|pci_get_bus_and_slot\)(...)) == NULL) S
)
  ... when != pci_dev_put(...,(T1)E,...)
      when != if (E != NULL) { ... pci_dev_put(...,(T1)E,...); ...}
      when != x1 = (T1)E
      when != E = x3;
      when any
(
  if (E == NULL) S1
|
  if (test)
+   {
(
+   pci_dev_put(E);
    return;
|
+   pci_dev_put(E);
    return ret;
)
+   }
|
  if (test) {
    ... when != pci_dev_put(...,(T2)E,...)
        when != if (E != NULL) { ... pci_dev_put(...,(T2)E,...); ...}
        when != x2 = (T2)E
(
+   pci_dev_put(E);
    return;
|
+   pci_dev_put(E);
    return ret;
)
  }
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some cleanups in uvesafb:
- The custom module_param() get/set functions don't need to be inlined
  since it is referred to via a pointer in a struct.
- don't end a #define with a ';'
- remove one of the single quote marks in "''ypan'"
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

tdfxfb_setup() can be __init.  This fixes the modpost section mismatch
warnings:

WARNING: vmlinux.o(.text+0x4cff9b): Section mismatch: reference to .init.data:mode_option (between 'tdfxfb_setup' and 'getclkMHz')
WARNING: vmlinux.o(.text+0x4cffa8): Section mismatch: reference to .init.data: (between 'tdfxfb_setup' and 'getclkMHz')

[krzysztof.h1@poczta.fm: use __init, not __devinit]
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The current nvidiafb_check_var() simply bails out if the selected mode is
out of range of the panel dimensions.  A good question would be why the
bogus mode is being selected in the first place -- the panel dimensions
that are read back are certainly bogus, but alas, I have no idea where to
even begin looking at the i2c/EDID/DDC mess:

nvidiafb: Device ID: 10de0165
nvidiafb: CRTC0 analog not found
nvidiafb: CRTC1 analog not found
nvidiafb: EDID found from BUS1
nvidiafb: CRTC 0 is currently programmed for DFP
nvidiafb: Using DFP on CRTC 0
nvidiafb: Panel size is 1280 x 1024
nvidiafb: Panel is TMDS
nvidiafb: unable to setup MTRR
nvidiafb: Flat panel dithering disabled
nvidiafb: PCI nVidia NV16 framebuffer (64MB @ 0xC0000000)

In my .config I presently have:

CONFIG_FIRMWARE_EDID=y
CONFIG_FB_DDC=y
CONFIG_FB_NVIDIA_I2C=y

I've not tried fiddling with these options, as I haven't the vaguest idea
what I should be looking at.

As a workaround, simply groveling for a new mode based on the probed
dimensions seems to work ok.  While it would be nice to debug this further
and sort out why the panel information is bogus, I think it's still worth
retrying the mode based on the panel information at hand as a last-ditch
effort, rather than simply bailing out completely.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Antonino A. Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

__ALIGN_MASK() is an internal implementation detail of ALIGN().  Let's not
needlessly fatten the interface in this driver.

[fujita.tomonori@lab.ntt.co.jp: fix it]
Cc: Alan Hourihane <alanh@fairlite.demon.co.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix bug identified by Marcio Buss in
http://bugzilla.kernel.org/show_bug.cgi?id=9565 - neofb can overwrite a field
in the fb_info struct.

This fix will result in truncated device identification strings - perhaps
fb_innfo.fix.id can be made larger?

Cc: Marcio Buss <marciobuss@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Christian Trefzer <ctrefzer@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

WARNING: vmlinux.o(.text+0x46e456): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e45c): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e49b): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e4a0): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e4bc): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e4c2): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e5c1): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e5c7): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Setting a display timing parameter too high or too low may cause it to
wrap around and thus become completely wrong. Validate the timings in
atmel_lcdfb_check_var() and saturate to the highest or lowest possible
value if necessary.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert fb defio from nopage to fault.
Switch from OOM to SIGBUS if the resource is not available.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NAndre Haupt <andre@bitwigglers.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>