The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.

The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.

On x86-64, this is a fairly significant code
size reduction:
   text	   data	    bss	    dec	    hex
 427861	  23648	   1008	 452517	  6e7a5	before
 425383	  23648	    976	 450007	  6ddd7	after
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a PS-poll frame is retried (but was received)
there is no way to detect that since it has no
sequence number. As a consequence, the standard
asks us to not react to PS-poll frames until the
response to one made it out (was ACKed or lost).

Implement this by using the WLAN_STA_SP flags to
also indicate a PS-Poll "service period" and the
IEEE80211_TX_STATUS_EOSP flag for the response
packet to indicate the end of the "SP" as usual.

We could use separate flags, but that will most
likely completely confuse drivers, and while the
standard doesn't exclude simultaneously polling
using uAPSD and PS-Poll, doing that seems quite
problematic.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.

Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the
presence of the mesh control header in their QoS header.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to support QoS in mesh, we need to assign queue mapping only
after the next hop has been resolved, both for forwarded and locally
originated frames.  Also, now that this is fixed, remove the XXX comment
in ieee80211_select_queue().

Also, V-Shy Ho reported that the queue mapping was not being applied to
the forwarded frame (fwd_skb instead of skb).  Fixed that as well.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx flow control for non-mesh modes of operation only needs to act on the
net device queues: when the hardware queues are full we stop accepting
traffic from the net device.  In mesh, however, we also need to stop
forwarding traffic.  This patch checks the hardware queues before
attempting to forward a mesh frame.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To check whether a frame is in the RMC, we need access to the mesh
header.  This header is encrypted in encrypted data frames, so make this
check after the frame has been decrypted.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When operating as a P2P GO, we receive some P2P action frames where the
BSSID is set to the peer MAC address. Specifically, this occurs for
invitation responses. These are valid action frames and they should be
passed up.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When associating to an AP, the station might miss the first EAP
packet that the AP sends due to a race condition between the association
success procedure and the rx flow in mac80211.
In such cases, the packet might fall in ieee80211_rx_h_check due to
the fact that the relevant rx->sta wasn't allocated yet.
Allocation of the relevant station info struct before actually
sending the association request and setting it with a new
dummy_sta flag solve this problem.
The station will accept only EAP packets from the AP while it
is in the pre-association/dummy state.
This dummy station entry is not seen by normal sta_info_get()
calls, only by sta_info_get_bss_rx().
The driver is not notified for the first insertion of the
dummy station. The driver is notified only after the association
is complete and the dummy flag is removed from the station entry.
That way, all the rest of the code flow should be untouched by
this change.
Signed-off-by: NGuy Eilam <guy@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make mesh path selection frames Mesh Action category, remove outdated
Mesh Path Selection category and defines, use updated reason codes, add
mesh_action_is_path_sel for readability, and update/correct path
selection IEs.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates the mesh peering frames to the format specified in
the recently ratified 802.11s standard. Several changes took place to
make this happen:

	- Change RX path to handle new self-protected frames
	- Add new Peering management IE
	- Remove old Peer Link IE
	- Remove old plink_action field in ieee80211_mgmt header

These changes by themselves would either break peering, or work by
coincidence, so squash them all into this patch.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In WoWLAN, devices may use crypto keys for TX/RX
and could also implement GTK rekeying. If the
driver isn't able to retrieve replay counters and
similar information from the device upon resume,
or if the device isn't responsive due to platform
issues, it isn't safe to keep the connection up
as GTK rekey messages from during the sleep time
could be replayed against it.

The only protection against that is disconnecting
from the AP. Modifying mac80211 to do that while
it is resuming would be very complex and invasive
in the case that the driver requires a reconfig,
so do it after it has resumed completely. In that
case, however, packets might be replayed since it
can then only happen after TX/RX are up again, so
mark keys for interfaces that need to disconnect
as "tainted" and drop all packets that are sent
or received with those keys.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current rx->queue value is slightly confusing.
It is set to 16 on non-QoS frames, including data,
and then used for sequence number and PN/IV checks.
Until recently, we had a TKIP IV checking bug that
had been introduced in 2008 to fix a seqno issue.
Before that, we always used TID 0 for checking the
PN or IV on non-QoS packets.

Go back to the old status for PN/IV checks using
the TID 0 counter for non-QoS by splitting up the
rx->queue value into "seqno_idx" and "security_idx"
in order to avoid confusion in the future. They
each have special rules on the value used for non-
QoS data frames.

Since the handling is now unified, also revert the
special TKIP handling from my patch
"mac80211: fix TKIP replay vulnerability".
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the devices that have already stripped IEEE 802.11
header from the AMSDU SKB can not use ieee80211_amsdu_to_8023s
routine. This patch enhances ieee80211_amsdu_to_8023s() API by
changing mandatory removing of IEEE 802.11 header from AMSDU
to optional.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These definitions need to be exposed now that we can set the peer link
states via NL80211_ATTR_STA_PLINK_STATE.  They were already being
(opaquely) reported by NL80211_STA_INFO_PLINK_STATE.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement support for HW scheduled scan.  The mac80211 code doesn't perform
scheduled scans itself, but calls the driver to start and stop scheduled
scans.

This patch also creates a trace event class to be used by drv_hw_scan
and the new drv_sched_scan_start and drv_sched_stop functions, in
order to avoid duplicate code.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Note: This breaks compatibility with previous mesh protocol instances.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, mac80211 handles MIC failures differently
depending on whenever they are detected by the stack's
own software crypto or when are handed down from the
driver.

This patch tries to unify both by moving the special
branch out of mac80211 rx hotpath and into into the
software crypto part. This has the advantage that we
can run a few more sanity checks on the data and verify
if the key type was TKIP. This is very handy because
several devices generate false postive MIC failure
reports. Like carl9170, ath9k and wl12xx:
<http://www.spinics.net/lists/linux-wireless/msg68494.html>
"mac80211: report MIC failure for truncated packets in AP mode"

Cc: Luciano Coelho <coelho@ti.com>
Cc: Arik Nemtsov <arik@wizery.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The release timer has to expire "just" after a
frame is up for release. Currently, if the timer
callback starts on time, the "!time_after" check
above will start a new timer instead of
releasing the frames.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Apparently this was confusing still ... add a
note that the byte is needed as padding.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes it easier to handle moving stations to VLAN interfaces that are
part of a different bridge.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cleaning the ieee80211_rx_data.flags field here is wrong, instead the
flags should be valid accross processing the frame on different
interfaces. Fix this by removing the incorrect flags=0 assignment.

Introduced in commit 554891e6
(mac80211: move packet flags into packet).
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Took me a minute to figure this out, maybe
it's better documented...
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Suppose the aggregation reorder buffer looks like this:

x-T-R1-y-R2,

where x and y are frames that have not been received, T is a received
frame that has timed out, and R1,R2 are received frames that have not
yet timed out. The proper behavior in this scenario is to move the
window past x (skipping it), release T and R1, and leave the window at y
until y is received or R2 times out.

As written, this code will instead leave the window at R1, because it
has not yet timed out. Fix this by exiting the reorder loop only when
the frame that has not timed out AND there are skipped frames earlier in
the current valid window.
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_rx_h_check returned RX_DROP_MONITOR in case the if statement
in question was true but the same return value is also used directly
after the if clause. Hence, we can just drop the whole if clause and as
such simplify the code.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 now supports passing MCS index to radiotap, so update the
comments regarding this
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since 4-addr frames completely override the source address which will
make it into the converted 802.3 frames, receiving frames for other
4-addr stations will confuse the bridging code.

To be able to handle traffic for all connected devices, the bridge
code will automatically turn on promiscuous mode, which triggers
this problem.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NSteve Brown <sbrown@cortland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This should decrease un-necessary flushes, on/off channel work,
and channel changes in cases where the only scanned channel is
the current operating channel.

* Removes SCAN_OFF_CHANNEL flag, uses SDATA_STATE_OFFCHANNEL
  and is-scanning flags instead.

* Add helper method to determine if we are currently configured
  for the operating channel.

* Do no blindly go off/on channel in work.c  Instead, only call
  appropriate on/off code when we really need to change channels.
  Always enable offchannel-ps mode when starting work,
  and disable it when we are done.

* Consolidate ieee80211_offchannel_stop_station and
  ieee80211_offchannel_stop_beaconing, call it
  ieee80211_offchannel_stop_vifs instead.

* Accept non-beacon frames when scanning on operating channel.

* Scan state machine optimized to minimize on/off channel
  transitions.  Also, when going on-channel, go ahead and
  re-enable beaconing.  We're going to be there for 200ms,
  so seems like some useful beaconing could happen.
  Always enable offchannel-ps mode when starting software
  scan, and disable it when we are done.

* Grab local->mtx earlier in __ieee80211_scan_completed_finish
  so that we are protected when calling hw_config(), etc.

* Pass probe-responses up the stack if scanning on local
  channel, so that mlme can take a look.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I can't think of a valid use case for this aside from debugging (which can
also be done with a real monitor interface), and dropping these frames saves
some precious CPU cycles.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While leaving oper channel, STA informs sleep state to AP to
stop sending data. Till sending ack for the nullfunc, AP
continues to send the data to STA which restarts ps_timer that
is causing unnecessary nullfunc exchange on timer expiry
when the STA was already moved to offchannel. So don't restart ps_timer
on data reception during scan. This issue was identified by
the following warning.

WARNING: at net/mac80211/tx.c:661 invoke_tx_handlers+0xf07/0x1330 [mac80211]
wlan0: Dropped data frame as no usable bitrate found while scanning and
associated. Target station: 00:03:7f:0b:a6:1b on 5 GHz band
Call Trace:
  [<ffffffffa0413ba7>] invoke_tx_handlers+0xf07/0x1330 [mac80211]
  [<ffffffffa0414056>] ieee80211_tx+0x86/0x2c0 [mac80211]
  [<ffffffffa0414345>] ieee80211_xmit+0xb5/0x1d0 [mac80211]
  [<ffffffffa04037e0>] ieee80211_dynamic_ps_enable_work+0x0/0xb0 [mac80211]
  [<ffffffffa04158cf>] ieee80211_tx_skb+0x4f/0x60 [mac80211]
  [<ffffffffa04026e6>] ieee80211_send_nullfunc+0x46/0x60 [mac80211]
  [<ffffffffa0403885>] ieee80211_dynamic_ps_enable_work+0xa5/0xb0 [mac80211]
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Beacons from external BSSes are required for updating overlapping BSS
info (i.e. ERP protection). Pass them up unconditionally.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When operating in AP mode the wl1271 hardware filters out null-data
packets as well as management packets. This makes it impossible for
mac80211 to monitor the PS mode by using the PM bit of incoming frames.

Implement a HW flag to indicate that mac80211 should ignore the PM bit.
In addition, expose ieee80211_sta_ps_transition() to make low-level
drivers capable of controlling PS-mode.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the MCS information we currently get
from the drivers into radiotap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This particular error isn't about multicast.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When running as a 4-addr station against an AP that has the 4-addr VLAN
interface and the main 3-addr AP interface bridged together, sometimes
frames originating from the station were looping back from the 3-addr AP
interface, causing the bridge code to emit warnings about receiving frames
with its own source address.
I'm not sure why this is happening yet, but I think it's a good idea to
drop all frames (except 802.1x/EAP frames) that do not match the configured
addressing mode, including 4-address frames sent to a 3-address station.
User test reports indicate that the problem goes away with this patch.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>