Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After these change, when need to work in rtbi mode,
just change phy-connection-type to "rtbi".

Also, this work can be done by u-boot.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch rounds out the 57765 asic rev support by adding the 57765 phy
ID and entering the 57765 device IDs in the pci table.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 57765 repurposes all the GPIOs normally used to switch power sources
when configured as a NIC device.  This patch changes the code to avoid
touching the GPIOs for this asic rev.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the debug UART is left enabled, the LEDs will not work properly.
This patch disables the debug UART.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a device supports MSI-X interrupts, the driver assumes TSS will be
available.  This is not true for the 57765.  This patch changes the code
so that only the default tx mailbox is initialized if TSS is not
available.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 57765 needs the driver to supply a nic address to the jumbo RCB,
just like all other devices except the 5717.  This patch changes the
test to single out the 5717 rather than maintain a lengthy whitelist of
asic revs.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both the 5717 and the 57765 will fail 'ethtool -t' selftests at the
memory selftest portion.  The memory map for these two devices differs
from the rest of the asic revs and each other.  This patch adds a new
memory map to use for memory selftests.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5717 serdes devices have a different phy register layout than all
other previous serdes devices.  This patch aborts the phy init sequence
in tg3_phy_reset() if the device is a 5717 serdes.  It also aborts the
tg3_phy_toggle_apd() operation.  Most other operations in the MII_SERDES
path are O.K.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The serdes and copper phys of the 5717 asic rev have different phy IDs.
This patch adds the serdes phy ID.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5717 and the 57765 have more resources at their disposal internally.
This patch tunes the driver to get better performance.  The adjustments
made here only apply to the 57765 and 5717 asic revs.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCIe PLL power down cannot be used if CLKREQ is enabled because data
corruption will occur.  If CLKREQ is disabled though, enabling PCIE P1
PLL power-down saves some power.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses a number of minor (mostly cosmetic) issues relating
to the configuration of TIPC, including the following:

- Corrects range limits for maximum number of ports per node
- Adds missing range limits for size of log buffer
- Removes configuration setting relating to unsupported slave node capability
- Standardizes description and help text wording for configuration settings
- Removes unneeded blank spaces
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing outside of net/core/dev.c uses it.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-core.h

If the per device ARP_ACCEPT option is enable, currently we only allow
creating new ARP cache entries for response type gratuitous ARP.

Allowing gratuitous ARP to create new ARP entries (not only to update
existing ones) is useful when we want to avoid unnecessary delays for
the first packet of a stream.

This patch allows request type gratuitous ARP to create new ARP cache
entries as well. This is useful when we want to populate the ARP cache
entries for a large number of hosts on the same LAN.
Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I was just looking at ppp_generic, and noticed that it fairly recently
(as in the last year) got rather mangled with many spaces turned into tabs
in places they very much shouldn't have been.  I tracked it down to commit
9c705260 (ppp: ppp_mp_explode() redesign).

I am amazed if that patch passed the patch checking script.  I have no
idea what kind of weird editor setting did this, but it has to have been a
weird editor setting or a very unfortunate search and replace gone wrong.
I only found it trying to apply a patch I was playing with and wondering
why it wouldn't apply.  Then I found there were tabs in the middle of
comments that used to be spaces.

Well here is a patch that should fix it up as far as I can tell.

Purely whitespace repair.  No actual code changes.
Signed-off-by: NLen Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable qdev is initialized twice to the same (side effect-free)
expression.  Drop one initialization.

A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)

// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@

x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MTU changes, ring size changes, etc cause the chip to be reset and the
statisctics flushed.  To keep track of the accumulated statistics, we
add code to save the whole statistics block before reset.  We also
modify the macros and statistics functions to return the sum of the
saved and current counters.

Based on original patch by Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refine the statistics macros by passing in just the name of the
counter field.  This makes it a lot easier and cleaner to add
counters saved before the last reset in the next patch.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__net_init/__net_exit are apparently not going away, so use them
to full extent.

In some cases __net_init was removed, because it was called from
__net_exit code.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we don't increment SYN-ACK timeouts & retransmissions
although we do increment the same stats for SYN. We seem to have lost
the SYN-ACK accounting with the introduction of tcp_syn_recv_timer
(commit 2248761e in the netdev-vger-cvs tree).

This patch fixes this issue. In the process we also rename the v4/v6
syn/ack retransmit functions for clarity. We also add a new
request_socket operations (syn_ack_timeout) so we can keep code in
inet_connection_sock.c protocol agnostic.
Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Separate Ethernet driver for Qlogic CNA devices
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o 1G/10G Ethernet Driver for Qlgic QLE8240 and QLE8242 CNA devices.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow macvlan devices to support GRO.
Signed-off-by: NPatrick Mullaney <pmullaney@novell.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Default setting is 'off', don't allow force firmware dump.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get the 2nd (other) nic function register values.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding the infrstructure and basic data for the firmware
core dump.
The firmware coredump is turned OFF by default.  There will be no
memory allocations for data dumps to the log.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>