This is a simple driver for the global timer module found in the Cortex
A9-MP cores from revision r1p0 onwards. This should be able to perform
the functions of the system timer and the local timer in an SMP system.

The global timer has the following features:
    The global timer is a 64-bit incrementing counter with an
auto-incrementing feature. It continues incrementing after sending
interrupts. The global timer is memory mapped in the private memory
region.
    The global timer is accessible to all Cortex-A9 processors in the
cluster. Each Cortex-A9 processor has a private 64-bit comparator that
is used to assert a private interrupt when the global timer has reached
the comparator value. All the Cortex-A9 processors in a design use the
banked ID, ID27, for this interrupt. ID27 is sent to the Interrupt
Controller as a Private Peripheral Interrupt. The global timer is
clocked by PERIPHCLK.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Rob Herring <robherring2@gmail.com>
CC: Linus Walleij <linus.walleij@linaro.org>
CC: Will Deacon <will.deacon@arm.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

This patch add a DT enabled driver for timers found on Marvell Orion SoCs
(Kirkwood, Dove, Orion5x, and Discovery Innovation). It installs a free-
running clocksource on timer0 and a clockevent source on timer1.
Corresponding device tree documentation is also added.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>

The recent implementation of a generic dummy timer resulted in a
different registration order of per cpu local timers which made the
broadcast control logic go belly up.

If the dummy timer is the first clock event device which is registered
for a CPU, then it is installed, the broadcast timer is initialized
and the CPU is marked as broadcast target.

If a real clock event device is installed after that, we can fail to
take the CPU out of the broadcast mask. In the worst case we end up
with two periodic timer events firing for the same CPU. One from the
per cpu hardware device and one from the broadcast.

Now the problem is that we have no way to distinguish whether the
system is in a state which makes broadcasting necessary or the
broadcast bit was set due to the nonfunctional dummy timer
installment.

To solve this we need to keep track of the system state seperately and
provide a more detailed decision logic whether we keep the CPU in
broadcast mode or not.

The old decision logic only clears the broadcast mode, if the newly
installed clock event device is not affected by power states.

The new logic clears the broadcast mode if one of the following is
true:

  - The new device is not affected by power states.

  - The system is not in a power state affected mode

  - The system has switched to oneshot mode. The oneshot broadcast is
    controlled from the deep idle state. The CPU is not in idle at
    this point, so it's safe to remove it from the mask.

If we clear the broadcast bit for the CPU when a new device is
installed, we also shutdown the broadcast device when this was the
last CPU in the broadcast mask.

If the broadcast bit is kept, then we leave the new device in shutdown
state and rely on the broadcast to deliver the timer interrupts via
the broadcast ipis.
Reported-and-tested-by: NStehle Vincent-B46079 <B46079@freescale.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>,
Cc: Mark Rutland <mark.rutland@arm.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1307012153060.4013@ionos.tec.linutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

When the system switches from periodic to oneshot mode, the broadcast
logic causes a possibility that a CPU which has not yet switched to
oneshot mode puts its own clock event device into oneshot mode without
updating the state and the timer handler.

CPU0				CPU1
				per cpu tickdev is in periodic mode
				and switched to broadcast

Switch to oneshot mode
 tick_broadcast_switch_to_oneshot()
  cpumask_copy(tick_oneshot_broacast_mask,
	       tick_broadcast_mask);

  broadcast device mode = oneshot

				Timer interrupt
						
				irq_enter()
				 tick_check_oneshot_broadcast()
				  dev->set_mode(ONESHOT);

				tick_handle_periodic()
				 if (dev->mode == ONESHOT)
				   dev->next_event += period;
				   FAIL.

We fail, because dev->next_event contains KTIME_MAX, if the device was
in periodic mode before the uncontrolled switch to oneshot happened.

We must copy the broadcast bits over to the oneshot mask, because
otherwise a CPU which relies on the broadcast would not been woken up
anymore after the broadcast device switched to oneshot mode.

So we need to verify in tick_check_oneshot_broadcast() whether the CPU
has already switched to oneshot mode. If not, leave the device
untouched and let the CPU switch controlled into oneshot mode.

This is a long standing bug, which was never noticed, because the main
user of the broadcast x86 cannot run into that scenario, AFAICT. The
nonarchitected timer mess of ARM creates a gazillion of differently
broken abominations which trigger the shortcomings of that broadcast
code, which better had never been necessary in the first place.
Reported-and-tested-by: NStehle Vincent-B46079 <B46079@freescale.com>
Reviewed-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>,
Cc: Mark Rutland <mark.rutland@arm.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1307012153060.4013@ionos.tec.linutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

In periodic mode we remove offline cpus from the broadcast propagation
mask. In oneshot mode we fail to do so. This was not a problem so far,
but the recent changes to the broadcast propagation introduced a
constellation which can result in a NULL pointer dereference.

What happens is:

CPU0			CPU1
			idle()
			  arch_idle()
			    tick_broadcast_oneshot_control(OFF);
			      set cpu1 in tick_broadcast_force_mask
			  if (cpu_offline())
			     arch_cpu_dead()

cpu_dead_cleanup(cpu1)
 cpu1 tickdevice pointer = NULL

broadcast interrupt
  dereference cpu1 tickdevice pointer -> OOPS

We dereference the pointer because cpu1 is still set in
tick_broadcast_force_mask and tick_do_broadcast() expects a valid
cpumask and therefor lacks any further checks.

Remove the cpu from the tick_broadcast_force_mask before we set the
tick device pointer to NULL. Also add a sanity check to the oneshot
broadcast function, so we can detect such issues w/o crashing the
machine.
Reported-by: NPrarit Bhargava <prarit@redhat.com>
Cc: athorlton@sgi.com
Cc: CAI Qian <caiqian@redhat.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1306261303260.4013@ionos.tec.linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Adjustments to Xen's persistent clock via update_persistent_clock()
don't actually persist, as the Xen wallclock is a software only clock
and modifications to it do not modify the underlying CMOS RTC.

The x86_platform.set_wallclock hook is there to keep the hardware RTC
synchronized. On a guest this is pointless.

On Dom0 we can use the native implementaion which actually updates the
hardware RTC, but we still need to keep the software emulation of RTC
for the guests up to date. The subscription to the pvclock_notifier
allows us to emulate this easily. The notifier is called at every tick
and when the clock was set.

Right now we only use that notifier when the clock was set, but due to
the fact that it is called periodically from the timekeeping update
code, we can utilize it to emulate the NTP driven drift compensation
of update_persistant_clock() for the Xen wall (software) clock.

Add a 11 minutes periodic update to the pvclock_gtod notifier callback
to achieve that. The static variable 'next' which maintains that 11
minutes update cycle is protected by the core code serialization so
there is no need to add a Xen specific serialization mechanism.

[ tglx: Massaged changelog and added a few comments ]
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-6-git-send-email-david.vrabel@citrix.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Currently the Xen wallclock is only updated every 11 minutes if NTP is
synchronized to its clock source (using the sync_cmos_clock() work).
If a guest is started before NTP is synchronized it may see an
incorrect wallclock time.

Use the pvclock_gtod notifier chain to receive a notification when the
system time has changed and update the wallclock to match.

This chain is called on every timer tick and we want to avoid an extra
(expensive) hypercall on every tick.  Because dom0 has historically
never provided a very accurate wallclock and guests do not expect one,
we can do this simply: the wallclock is only updated if the clock was
set.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-5-git-send-email-david.vrabel@citrix.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

If the clock was set (stepped), set the action parameter to functions
in the pvclock gtod notifier chain to non-zero.  This allows the
callee to only do work if the clock was stepped.

This will be used on Xen as the synchronization of the Xen wallclock
to the control domain's (dom0) system time will be done with this
notifier and updating on every timer tick is unnecessary and too
expensive.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-4-git-send-email-david.vrabel@citrix.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Instead of passing multiple bools to timekeeping_updated(), define
flags and use a single 'action' parameter.  It is then more obvious
what each timekeeping_update() call does.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-3-git-send-email-david.vrabel@citrix.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

commit 359cdd3f(xen: maintain clock offset over save/restore) added
a clock_was_set() call into the xen resume code to propagate the
system time changes. With the modified hrtimer resume code, which
makes sure that all cpus are notified this call is not longer necessary.

[ tglx: Separated it from the hrtimer change ]
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk  <konrad.wilk@oracle.com>
Cc: John Stultz  <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-2-git-send-email-david.vrabel@citrix.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

hrtimers_resume() only reprograms the timers for the current CPU as it
assumes that all other CPUs are offline at this point in the resume
process. If other CPUs are online then their timers will not be
corrected and they may fire at the wrong time.

When running as a Xen guest, this assumption is not true.  Non-boot
CPUs are only stopped with IRQs disabled instead of offlining them.
This is a performance optimization as disabling the CPUs would add an
unacceptable amount of additional downtime during a live migration (>
200 ms for a 4 VCPU guest).

hrtimers_resume() cannot call on_each_cpu(retrigger_next_event,...)
as the other CPUs will be stopped with IRQs disabled.  Instead, defer
the call to the next softirq.

[ tglx: Separated the xen change out ]
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk  <konrad.wilk@oracle.com>
Cc: John Stultz  <john.stultz@linaro.org>
Cc: <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1372329348-20841-2-git-send-email-david.vrabel@citrix.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Direct compare of jiffies related values does not work in the wrap
around case. Replace it with time_is_after_jiffies().
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: http://lkml.kernel.org/r/519BC066.5080600@acm.org
Cc: stable@vger.kernel.org
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Commit 38ff87f7 (sched_clock: Make ARM's sched_clock generic for all
architectures) changed the header to <linux/sched_clock.h>, so adapt
it in order to fix the following build error:

drivers/clocksource/vf_pit_timer.c:15:29: fatal error: asm/sched_clock.h: No such file or directory
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Cc: shawn.guo@linaro.org
Cc: sboyd@codeaurora.org
Cc: john.stultz@linaro.org
Link: http://lkml.kernel.org/r/1372116008-2323-1-git-send-email-festevam@gmail.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Several architectures have a dummy timer driver tightly coupled with
their broadcast code to support machines without cpu-local timers (or
where there is a lack of driver support).

Since 12ad1000: "clockevents: Add generic timer broadcast function"
it's been possible to write broadcast-capable timer drivers decoupled
from the broadcast mechanism. We can use this functionality to implement
a generic dummy timer driver that can be shared by all architectures
with generic tick broadcast (ARCH_HAS_TICK_BROADCAST).

This patch implements a generic dummy timer using this facility.

[sboyd: Make percpu data static, use __this_cpu_ptr(), move to
        early_initcall to properly register on each CPU, only
	register if more than one CPU possible]
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>,
Cc: John Stultz <john.stultz@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1370291642-13259-3-git-send-email-sboyd@codeaurora.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

On an SMP system with only one global clockevent and a dummy
clockevent per CPU we run into problems. We want the dummy
clockevents to be registered as the per CPU tick devices, but
we can only achieve that if we register the dummy clockevents
before the global clockevent or if we artificially inflate the
rating of the dummy clockevents to be higher than the rating
of the global clockevent. Failure to do so leads to boot
hangs when the dummy timers are registered on all other CPUs
besides the CPU that accepted the global clockevent as its tick
device and there is no broadcast timer to poke the dummy
devices.

If we're registering multiple clockevents and one clockevent is
global and the other is local to a particular CPU we should
choose to use the local clockevent regardless of the rating of
the device. This way, if the clockevent is a dummy it will take
the tick device duty as long as there isn't a higher rated tick
device and any global clockevent will be bumped out into
broadcast mode, fixing the problem described above.
Reported-and-tested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Tested-by: soren.brinkmann@xilinx.com
Cc: John Stultz <john.stultz@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/20130613183950.GA32061@codeaurora.orgSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Some new users of the ARM sched_clock framework are going through
the arm-soc tree. Before 38ff87f7 (sched_clock: Make ARM's
sched_clock generic for all architectures, 2013-06-01) the header
file was in asm, but now it's in linux. One solution would be to
do an evil merge of the arm-soc tree and fix up the asm users,
but it's easier to add a temporary asm header that we can remove
along with the few stragglers after the merge window is over.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

This reverts commit 55a68c23.

In order to avoid a collision with dw_apb_timer changes in
the arm-soc tree, revert this change.

I'm leaving it to the arm-soc folks to sort out if they want
to keep the other side of the collision or if they're just going
to back it all out and try again during the next release cycle.
Reported-by: NDinh Nguyen <dinguyen@altera.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

There is a small race between when the cycle count is read from
the hardware and when the epoch stabilizes. Consider this
scenario:

 CPU0                           CPU1
 ----                           ----
 cyc = read_sched_clock()
 cyc_to_sched_clock()
                                 update_sched_clock()
                                  ...
                                  cd.epoch_cyc = cyc;
  epoch_cyc = cd.epoch_cyc;
  ...
  epoch_ns + cyc_to_ns((cyc - epoch_cyc)

The cyc on cpu0 was read before the epoch changed. But we
calculate the nanoseconds based on the new epoch by subtracting
the new epoch from the old cycle count. Since epoch is most likely
larger than the old cycle count we calculate a large number that
will be converted to nanoseconds and added to epoch_ns, causing
time to jump forward too much.

Fix this problem by reading the hardware after the epoch has
stabilized.

Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

If we're suspended and sched_clock() is called we're going to
read the hardware one more time and throw away that value and
return back the cached value we saved during the suspend
callback. This is wasteful. Let's short circuit all that and
return the cached value as early as possible if we're suspended.
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

The needs_suspend member is unused now that we always do the
suspend/resume handling (see 6a4dae5e (ARM: 7565/1: sched: stop
sched_clock() during suspend, 2012-10-23)).
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Export symbols so they can be used by
drivers/staging/android/alarm-dev.c if it is built as a module.
So far alarm-dev is built-in but module support is planned (see
drivers/staging/android/TODO).
Signed-off-by: NMarcus Gelderie <redmnic@gmail.com>
[jstultz: tweaked commit message, also export newly added functions]
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Merge branch 'timers/clockevents' of git://git.linaro.org/people/dlezcano/clockevents into timers/core

This patch adds a clocksource/clockevent driver for the timer found on some
models in the TI-Nspire calculator series. The timer has two 16bit subtimers
within its memory mapped I/O interface but only the first can generate
interrupts. The first subtimer is used to generate clockevents but only if an
interrupt number and register is given.

The interrupt acknowledgement mechanism is a little strange because the
interrupt mask and acknowledge registers are located in another memory mapped
I/O peripheral. The address of this register is passed to the driver through
device tree bindings.

The second subtimer is used as a clocksource because it isn't capable of
generating an interrupt. This subtimer is always added.
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

Add Freescale Vybrid Family period interrupt timer support.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Reviewed-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

irq_of_parse_and_map() returns 0 on error, while the code checks for NO_IRQ.
This breaks on platforms that have NO_IRQ != 0.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

The patch "x86: Increase precision of x86_platform.get/set_wallclock"
changed the x86 platform set_wallclock/get_wallclock interfaces to
use nsec granular timespecs instead of a second granular interface.

However, that patch missed converting the vrtc code, so this patch
converts those functions to use timespecs.

Many thanks to the kbuild test robot for finding this!
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Below is a patch from android kernel that maintains a histogram of
suspend times. Please review and provide feedback.

Statistices on the time spent in suspend are kept in
/sys/kernel/debug/sleep_time.

Cc: Android Kernel Team <kernel-team@android.com>
Cc: Colin Cross <ccross@android.com>
Cc: Todd Poynor <toddpoynor@google.com>
Cc: San Mehat <san@google.com>
Cc: Benoit Goby <benoit@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NColin Cross <ccross@android.com>
Signed-off-by: NTodd Poynor <toddpoynor@google.com>
[zoran.markovic@linaro.org: Re-formatted suspend time table to better
fit expected values. Moved accounting of suspend time into timekeeping
core. Removed CONFIG_SUSPEND_TIME flag and made the feature conditional
on CONFIG_DEBUG_FS. Changed the file name to sleep_time to better fit
terminology in timekeeping core. Changed seq_printf to seq_puts. Tweaked
commit message]
Signed-off-by: NZoran Markovic <zoran.markovic@linaro.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Add support for clocks CLOCK_REALTIME_ALARM and CLOCK_BOOTTIME_ALARM,
thereby enabling wakeup alarm timers via file descriptors.
Signed-off-by: NTodd Poynor <toddpoynor@google.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Add functions needed for hooking up alarmtimer to timerfd:

* alarm_restart: Similar to hrtimer_restart, restart an alarmtimer after
  the expires time has already been updated (as with alarm_forward).

* alarm_forward_now: Similar to hrtimer_forward_now, move the expires
  time forward to an interval from the current time of the associated clock.

* alarm_start_relative: Start an alarmtimer with an expires time relative to
  the current time of the associated clock.

* alarm_expires_remaining: Similar to hrtimer_expires_remaining, return the
  amount of time remaining until alarm expiry.
Signed-off-by: NTodd Poynor <toddpoynor@google.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

All the virtualized platforms (KVM, lguest and Xen) have persistent
wallclocks that have more than one second of precision.

read_persistent_wallclock() and update_persistent_wallclock() allow
for nanosecond precision but their implementation on x86 with
x86_platform.get/set_wallclock() only allows for one second precision.
This means guests may see a wallclock time that is off by up to 1
second.

Make set_wallclock() and get_wallclock() take a struct timespec
parameter (which allows for nanosecond precision) so KVM and Xen
guests may start with a more accurate wallclock time and a Xen dom0
can maintain a more accurate wallclock for guests.
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

The time.h header seems not to be used by current code.
Removing this include allows the driver to build on other
architecture that do not have this header.

Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
[tweaked commit message and header]
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

It seems we made a mistake when creating dw_apb_timer_of.c:
picoxcell sched_clock had parts that were not related to
dw_apb_timer, yet we moved them to dw_apb_timer_of, and tried to
use them on socfpga.

This results in system where user/system time is not measured
properly, as demonstrated by

    time dd if=/dev/urandom of=/dev/zero bs=100000 count=100

So this patch switches sched_clock to hardware that exists on both
platforms, and adds missing of_node_put() in dw_apb_timer_init().
Signed-off-by: NPavel Machek <pavel@denx.de>
Acked-by: NJamie Iles <jamie@jamieiles.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

The function is currently mainly used in the networking code and
if others start using it, they must check the result, otherwise
it cannot be determined if the timespec conversion suceeded.
Currently no user lacks this check, but make future users aware of
a possible misusage.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

We've got the macro NSEC_PER_USEC defined in header file
include/linux/time.h. To make the code decent, this patch
replaces the immediate number 1000 to convert bewteen a
time value in microseconds and one in nanoseconds with the
macro NSEC_PER_USEC.
Signed-off-by: NLiu Ying <Ying.Liu@freescale.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

commit 7eaeb343 (clocksource: Provide unbind interface in sysfs)
implemented clocksource_select_fallback() which is not defined for
CONFIG_ARCH_USES_GETTIMEOFFSET=y. Add an empty inline function for
that.
Reported-by: NIngo Molnar <mingo@kernel.org>
Reported-by: fengguang.wu@intel.com
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Unbreak architectures which do not use clockevents, but require to
build some of the core timekeeping infrastructure
Reported-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Provide a sysfs interface to allow unbinding of clockevent
devices. The device is unbound if it is unused or if there is a
replacement device available. Unbinding of broadcast devices is not
supported as we don't want to foster that nonsense. If no replacement
device is available the unbind returns -EBUSY. Unbind is available
from the kernel and through sysfs, which is necessary to drop the
module refcount.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.499216659@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Split out the clockevent device selection logic. Preparatory patch to
allow unbinding active clockevent devices.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20130425143436.431796247@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>