Change instance id of DBGU to 45.
Signed-off-by: NMohamed Jamsheeth Hajanajubudeen <mohamedjamsheeth.hajanajubudeen@atmel.com>
Fixes: 7c661394 ("ARM: at91: dt: add device tree file for SAMA5D4 SoC")
Cc: stable@vger.kernel.org   # 3.18+
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

A new compatible string has been introduced: atmel,sama5d4-i2c. It
allows to use the i2c-sda-hold-time-ns property if needed.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

After the change of frequency a SAMA5D4 can reach, we have to modify the
maximum clock specification for the master clock, up to 200MHz now.

It avoids the wrong message saying that "master clk is overclocked" for this
configuration.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add pinmux for the 4 remaining signals used in 8-bit MMC 0
bus configuration.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Synchronise the comments in mmc0 pinmux node with HSMCI0 pinmux
description in the Atmel SAMA5D4 datasheet from 24-Aug-15 page
1119, section 37.6.1, Table 37-3 .
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: NJosh Wu <josh.wu@atmel.com>
Reported-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Change the watchdog compatible to "atmel,sama5d4-wdt" to support
SAMA5D4 watchdog driver.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The second macb is present on all the sama5d4 SoCs. Let's add a node
reflecting it in the device tree.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The PMC is not only used to drive the clocks but also has some registers
related to other functions. One of those is for example the USB gadget
bias.
Using a syscon allows to properly separate those functions.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

The crypto modules will provide HW AES/TDES/SHA for any sama5d4 board. Enable
them by default.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Correcting the dma declaration for i2c1 dma.
Signed-off-by: NHolger Busse <h.busse@kathrein-sachsen.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 4cc7cdf3 ("ARM: at91/dt: add i2c1 declaration to sama5d4")
Cc: stable@vger.kernel.org  # v4.1+

The watchdog, the reset controller, the RTC, the shutdown controller, the
timer counters and the LCD PWM need the slow clock, add it where necessary.
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

They'll use "atmel,sama5d3-rstc" for reset function.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add the old compatible string as a fallback]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The ADC pinctrl is board specific, move it to the board device trees.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The property is actually atmel,adc-use-external-triggers.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

at91sam9g45, at91sam9x5 and sama5 SoCs should not use
"atmel,at91sam9rl-udc" for their USB device compatible property since
this compatible is attached to a specific hardware bug fix.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>  #4.0+
Signed-off-by: NKevin Hilman <khilman@linaro.org>

The xdmac channel configuration is done in one cell not two. This error
prevents from probing devices correctly.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Fixes: 83906783 ("ARM: at91/dt: sama5d4: add aes, sha and tdes nodes")
Cc: stable@vger.kernel.org # 4.1
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NKevin Hilman <khilman@linaro.org>

The ohci driver now calls clk_set_rate on the uhpck clock (which forwards
set_rate requests to its parent: the usb clock).
Remove useless references to usb clocks from ohci definitions.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The uhpck is useless for High-Speed communications, remove the reference
to this clock in all ehci definitions.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

commit 111573cc ("mtd: atmel_nand: check NFC busy flag by HSMC_SR
instead of NFC cmd regs")
check NFC busy by nfc SR instead of NFC cmd regs. So we don't need to
map NFC cmd registers to include NFCBUSY bit.
That means we only need map 0x08000000 instead of 0x10000000 for NFC
cmd regs.

This patch reduce the NFC cmd regs map for sama5d3 & sama5d4.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Update the pinctrl ranges property to support pioD controller whose
mapping is not contiguous with other pio controllers. Without this
update, getting resource will fail, then pinctrl probe will fail too
because there is a missing pio controller.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add sama5d4 spi1, spi2 dt nodes & pinctrl.
Signed-off-by: NSuchang Ko <suchangko@samul.kr>
[nicolas.ferre@atmel.com: split patch, reorder & whitespace fixes]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add sama5d4 uart0, uart1 dt nodes, pinctrl and related aliases.
Signed-off-by: NSuchang Ko <suchangko@samul.kr>
[nicolas.ferre@atmel.com: split patch, reorder & whitespace fixes]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Also add the pinctrl for usart0, usart1.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

For the SAMA5D4 SoC, some LCD lines are in conflict with useful peripherals.
Remove these lines and the lowest significant bit of a 24 bit LCD. It gives
us a RGB 777 configuration.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The color arrangement for SAMA5D4 in RGB 666 takes the most significant bits of
each color line groups.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add HLCDC node.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add LCDC pin definitions.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The DBGU is not a simple UART and we need to be able to distinguish it from the
other UARTs, in particular to get its address and check the chip id.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The UTMI clock must be selected by any high-speed USB IP. The logic behind it
needs this particular clock.
So, correct the clock in the device tree files affected.
Reported-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #3.18

lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add ISI dt node and pinctrl settings in sama5d4.dtsi.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
[nicolas.ferre@atmel.com: sort nodes in order. remove useless comments]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NLeilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add SSC 0 and 1 nodes.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: NPhilip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

As we introduce a new "atmel,sama5d4-nand" compatible string for sama5d4,
so we need to apply it for sama5d4 chip.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>