This patch simplifies URB management for transmission,
by removing the 'FLUSH' variable (which is not needed,
since we can determine if the URB has been killed by
looking at the URB status), and also handling the STOP
case properly.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a recently introduced use-after-free regression
from "p54pci: prevent stuck rx-ring on slow system".

Hans de Goede reported a use-after-free regression:
>BUG: unable to handle kernel paging request at 6b6b6b6b
>IP: [<e122284a>] p54p_check_tx_ring+0x84/0xb1 [p54pci]
>*pde = 00000000
>Oops: 0000 [#1] SMP
>EIP: 0060:[<e122284a>] EFLAGS: 00010286 CPU: 0
>EIP is at p54p_check_tx_ring+0x84/0xb1 [p54pci]
>EAX: 6b6b6b6b EBX: df10b170 ECX: 00000003 EDX: 00000001
>ESI: dc471500 EDI: d8acaeb0 EBP: c098be9c ESP: c098be84
> DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
>Process swapper (pid: 0, ti=c098a000 task=c09ccfe0 task.ti=c098a000)
>Call Trace:
> [<e1222b02>] ? p54p_tasklet+0xaa/0xb5 [p54pci]
> [<c0440568>] ? tasklet_action+0x78/0xcb
> [<c0440ed3>] ? __do_softirq+0xbc/0x173

Quote from comment #17:
"The problem is the innocent looking moving of the tx processing to
 after the rx processing in the tasklet. Quoting from the changelog:
  This patch does it the same way, except that it also prioritize
  rx data processing, simply because tx routines *can* wait.

 This is causing an issue with us referencing already freed memory,
 because some skb's we transmit, we immediately receive back, such
 as those for reading the eeprom (*) and getting stats.

 What can happen because of the moving of the tx processing to after
 the rx processing is that when the tasklet first runs after doing a
 special skb tx (such as eeprom) we've already received the answer
 to it.

 Then the rx processing ends up calling p54_find_and_unlink_skb to
 find the matching tx skb for the just received special rx skb and
 frees the tx skb.

 Then after the processing of the rx skb answer, and thus freeing
 the tx skb, we go process the completed tx ring entires, and then
 dereference the free-ed skb, to see if it should free free-ed by
 p54p_check_tx_ring()."

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623Bug-Identified-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta->last_tx_rate is traditionally updated just before transmitting a
frame based on information from the rate control algorithm. However, for
hardware drivers with IEEE80211_HW_HAS_RATE_CONTROL this is not performed,
as the rate control algorithm is not executed, and because the used rate is
not known before the frame has actually been transmitted.

This causes atleast a fixed 1Mb/s to be reported to user space. A few other
instances of code also rely on this information.

Fix this by setting the sta->last_tx_rate in tx_status handling. There, look
for last rates entry set by the driver, and use that as value for
sta->last_tx_rate.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Our offset handling becomes even a little more hackish now. For some reason I
do not understand all offsets as inrelative. It assumes base offset is 0x1000
but it will work for now as we make offsets relative anyway by removing base
0x1000. Should be cleaner however.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Attempting to read registers that don't exist on the SSB bus can cause
hangs on some boxes.  At least some b43 devices are 'in the wild' that
don't have SPROMs at all.  When the SSB bus support loads, it attempts
to read these (non-existant) SPROMs and causes hard hangs on the box --
no console output, etc.

This patch adds some intelligence to determine whether or not the SPROM
is present before attempting to read it.  This avoids those hard hangs
on those devices with no SPROM attached to their SSB bus.  The
SSB-attached devices (e.g. b43, et al.) won't work, but at least the box
will survive to test further patches. :-)
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>

When I updated this from the corresponding
userspace library, an annotation error crept
in -- this variable needs to be annotated as
little endian. No effect on code generation.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes ar5416Addac_9160 and ar5416Addac_9160 const
I guess we skipped them long ago.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When IEEE80211_HW_CONNECTION_MONITOR is configured by the driver, starting
of ieee80211_sta_conn_mon_timer should be prevented, as it is then not needed.

This is currently partially the case. As it seems, when a probe-response is
received from the AP the timer is still restarted, thus restarting the host
based connection keep-alive mechanism. These probe-responses happen at least
when scanning while associated.

Fix this by preventing starting of the ieee80211_sta_conn_mon_timer in the
ieee80211_rx_mgmt_probe_resp function.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Supported only for single stream rates by the hardware
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9300 based hardware can 3x3 MCS rates, this should be set in the
HT capabilities.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of increasing bits_per_symbol for supporting more streams, keep
it single-stream only and multiply the values by the numer of streams.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Include MCS0-31 and also add SGI for HT20. This makes it
possible to support more different rate combinations with
newer hardware.

Based on a patch by Selvam. T.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the first element of survey data, the noise floor figure.
Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the survey function to both mac80211 itself and to mac80211_hwsim.
For the latter driver, we simply invent some noise level.A real driver which
cannot determine the real channel noise MUST NOT report any noise, especially
not a magically conjured one :-)
Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.

The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.

It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.

I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.

Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: NDaniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Applied common sense, no info from the manufacturer:

(0x8516, 0x2070) is RT2070
(0x8516, 0x2770) is RT2770
(0x8516, 0x2870) is RT2870
[...]
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

One HT debugging printk is missing a newline,
add it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Orinoco should be endian clean, so enable the checking.
Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of using a local function.
Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

... to set fragmentation and RTS thresholds. Also report RTS retry
settings during wiphy init.

Note that the existing semantics for enabling microwave robustness are
preserved on firmwares that have it.
Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta_cleanup timer is used to periodically expire buffered frames from the
tx buf. The timer is executing periodically, regardless of the need for it.
This is wasting resources.

Fix this simply by not restarting the sta_cleanup timer if the tx buffer was
empty. Restart the timer when there is some more tx-traffic.

Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kalle reported that his system deadlocks since my
recent work in this area. The reason quickly became
apparent: we try to cancel_timer_sync() a timer
from within itself. Fix that by making the function
aware of the context it is called from.
Reported-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The flag is called IEEE80211_TX_STAT_AMPDU rather than using the whole word
STATUS.
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

Some future hardware will also require some antenna
overrides so make the current logic more generic;
right now it is semantically based on a workaround
for off-channel reception but the reasons for the
new antenna overrides will be different.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Off-channel reception is acceptable in monitor
mode, and checking for monitor mode this way is
not really correct anyway since it could be the
case while operating.

Now iwl_is_monitor_mode() is no longer used so
remove it completely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Monitor mode operation need not (and probably should
not) affect scanning this way since real monitoring
can not properly happen while scanning anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

The flag name is a little misleading, this
flag instructs the device to ignore bluetooth
messages for purposes of frame transmissions,
so rename the flag to TX_CMD_FLG_IGNORE_BT.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Some future hardware will require a different command to
be sent for bluetooth coexist, so make this a virtual
method that can be changed on a per-device basis.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Since multiple new devices having similar uCode architecture and use same
registers address, remove more reference to 5000 series to eliminate the
confusion.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Perform sanity check for turn on aggregation tid. Also remove the
option for turn on all the aggregation tids at once since it is
deprecated function and not being used.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>