This patch adds sysfs support to xHCI usb2 hardware LPM, so developer can
enable and disable usb2 hardware LPM manually for test purpose.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.

If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch tests USB2 software LPM for a USB2 LPM-capable device.

When a lpm-capable device is addressed, if the host also supports software
LPM, apply a test by putting the device into L1 state and resume it to see
if the device can do L1 suspend/resume successfully.

If the device fails to enter L1 or resume from L1 state, it may not
function normally and usbcore may disconnect and re-enumerate it. In this
case, store the device's Vid and Pid information, make sure the host will
not test LPM for it twice.

The test result is per device/host. Some devices claim to be lpm-capable,
but fail to enter L1 or resume. So the test is necessary.

The xHCI 1.0 errata has modified the USB2.0 LPM implementation. It redefines
the HIRD field to BESL, and adds another register Port Hardware LPM Control
(PORTHLPMC). However, this should not affect the LPM behavior on xHC which
does not implement 1.0 errata.

USB2.0 LPM errata defines a new bit BESL in the device's USB 2.0 extension
descriptor. If the device reports it uses BESL, driver should use BESL
instead of HIRD for it.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Check the host's USB2 LPM capability.

USB2 software LPM support is optional for xHCI 0.96 hosts. xHCI 1.0 hosts
should support software LPM, and may support hardware LPM.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the link state changes, xHC will report a port status change event
and set the PORT_PLC bit, for both USB3 and USB2 root hub ports.

The PLC will be cleared by usbcore for USB3 root hub ports, but not for
USB2 ports, because they do not report USB_PORT_STAT_C_LINK_STATE in
wPortChange.

Clear it for USB2 root hub ports in handle_port_status().
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce xhci_test_and_clear_bit() to clear RWC bit in PORTSC register.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Introduce xhci_set_link_state() to remove redundant codes.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Check device's LPM capability by examining the bmAttibutes field of the
USB2.0 Extension Descriptor.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit gets BOS(Binary Device Object Store) descriptor set for Super
Speed devices and High Speed devices which support BOS descriptor.

BOS descriptor is used to report additional USB device-level capabilities
that are not reported via the Device descriptor. By getting BOS descriptor
set, driver can check device's device-level capability such as LPM
capability.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NShaun Silk <g0del@bigpond.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This allow to clean duplicated code in most of SOC driver.
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>  # fixes 3.1 build error
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Report the number of dropped packets instead of zero
when using the binary usbmon interface with tcpdump.

# tcpdump -i usbmon1 -w dump
tcpdump: listening on usbmon1, link-type USB_LINUX_MMAPPED (USB with padded Linux header), capture size 65535 bytes
^C2155 packets captured
2155 packets received by filter
1019 packets dropped by kernel
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We should not be using dev_get_drvdata() because we
never call dev_set_drvdata(). Let's use container_of()
as all other sysfs attributes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add vendor and product ID for the SMART USB to serial adapter. These
were meant to be used with their SMART Board whiteboards, but can be
re-purposed for other tasks. Tested and working (at at least 9600 bps).
Signed-off-by: NEric Benoit <eric@ecks.ca>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Simple patch to make qcserial recognize the USB id of the Sierra
Wireless MC8355 which is based on the Gobi 3000 chip.

Both UMTS and GPS work fine.
Signed-off-by: NRichard Hartmann <richih.mailinglist@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The seg argument to xhci_segment_free is never passed as NULL, so
no need to check for this in xhci_segment_free.
Signed-off-by: NKautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are 2 situations wherein the xhci_ring* might not get freed:
- When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and
  we goto the fail: label in xhci_ring_alloc. In this case, the ring
  will not get kfreed.
- When the num_segs argument to xhci_ring_alloc is passed as 0 and
  we try to free the rung after that.
  ( This doesn't really happen as of now in the code but we seem to
    be entertaining num_segs=0 in xhci_ring_alloc )

This should be backported to kernels as old as 2.6.31.
Signed-off-by: NKautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a hot reset (standard USB port reset) fails on a USB 3.0 port, the
host controller transitions to the "Error" state.  It reports the port
link state as "Inactive", sets the link state change flag, and (if the
device disconnects) also reports the disconnect and connect change status.
It's also supposed to transition the link state to "RxDetect", but the NEC
µPD720200 xHCI host does not.

Unfortunately, Harald found that the combination of the NEC µPD720200 and
a LogiLink USB 3.0 to SATA adapter triggered this issue.  The USB core
would reset the device, the port would go into this error state, and the
device would never be enumerated.  This combination works under Windows,
but not under Linux.

When a hot reset fails on a USB 3.0 port, and the link state is reported
as Inactive, fall back to a warm port reset instead.  Harald confirms that
with a warm port reset (along with all the change bits being correctly
cleared), the USB 3.0 device will successfully enumerate.

Harald also had to add two other patches ("xhci: Set change bit when warm
reset change is set." and "usbcore: refine warm reset logic") to make this
setup work.  Since the warm reset refinement patch is not destined for the
stable kernels (it's too big), this patch should not be backported either.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=41752Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NHarald Brennich <harald.brennich@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Intel Panther Point xHCI host tracks SuperSpeed endpoints in a
different way than USB 2.0/1.1 endpoints.  The bandwidth interval tables
are not used, and instead the bandwidth is calculated in a very simple
way.  Bandwidth for SuperSpeed endpoints is tracked individually in each
direction, since each direction has the full USB 3.0 bandwidth available.
10% of the bus bandwidth is reserved for non-periodic transfers.

This checking would be more complex if we had USB 3.0 LPM enabled, because
an additional latency for isochronous ping times need to be taken into
account.  However, we don't have USB 3.0 LPM support in Linux yet.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The "Mult" bits in the SuperSpeed Endpoint Companion Descriptor are
zero-based, and the xHCI host controller wants them to be zero-based in
the input context.  However, for the bandwidth math, we want them to be
one-based.  Fix this.

Fix the documentation about the endpoint bandwidth mult variable in the
xhci.h file, which says it is zero-based.  Also fix the documentation
about num_packets, which is also one-based, not zero-based.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current waiting time for warm(BH) reset in hub_port_warm_reset() is too short
for xHC host to complete the warm reset and report a BH reset change.

This patch increases the waiting time for warm reset and merges the function
into hub_port_reset(), so it can handle both cold reset and warm reset, and
factor out hub_port_finish_reset() to make the code looks cleaner.

This fixes the issue that driver fails to clear BH reset change and port is
"dead".
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

instead of reading the xhci interface version each time _even_ if the
quirk is not required, simply check if the quirk flag is set. This flag
is only set of the module parameter is set and here is where I moved the
version check to.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

After auto-delink command is triggered, the CSW won't be sent back
to host side, in which scenario, the USB Mass Storage driver will
wait for the completion of the URB for MAX_SCHEDULE_TIMEOUT.
Signed-off-by: Nedwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The new runtime PM code has shown that many webcams suffer
from a race condition that may crash them upon resume.
Runtime PM is especially prone to show the problem because
it retains power to the cameras at all times. However
system suspension may also crash the devices and retain
power to the devices.
The only way to solve this problem without races is in
usbcore with the RESET_RESUME quirk.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: Nstable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1484) adds documentation for ehci-hcd's "companion"
sysfs attribute, which was added to the kernel over four years ago but
never documented.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'for-next' of git://gitorious.org/usb/usb: (47 commits)
  usb: musb: Enable DMA mode1 RX for transfers without short packets
  usb: musb: fix build breakage
  usb: gadget: audio: queue wLength-sized requests
  usb: gadget: audio: actually support both speeds
  usb: gadget: storage: make FSG_NUM_BUFFERS variable size
  USB: gadget: storage: remove alignment assumption
  usb: gadget: storage: adapt logic block size to bound block devices
  usb: dwc3: gadget: improve debug on link state change
  usb: dwc3: omap: set idle and standby modes
  usb: dwc3: ep0: introduce ep0_expect_in flag
  usb: dwc3: ep0: giveback requests on stall_and_restart
  usb: dwc3: gadget: drop the useless dma_sync_single* calls
  usb: dwc3: gadget: fix GCTL programming
  usb: dwc3: define ScaleDown macro helper
  usb: dwc3: Fix definition of DWC3_GCTL_U2RSTECN
  usb: dwc3: gadget: do not map/unmap ZLP transfers
  usb: dwc3: omap: fix IRQ handling
  usb: dwc3: omap: change IRQ name to dwc3-omap
  usb: dwc3: add module.h to dwc3-omap.c and core.c
  usb: dwc3: omap: distinguish between SW and HW modes
  ...

This flag is a NOOP and can be removed now.
Signed-off-by: NYong Zhang <yong.zhang0@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According to ehci spec 4.10.2, Advance Queue

	If the fetched qTD has its Active bit set to a zero, the
	host controller aborts the queue advance and follows the
	queue head's horizontal pointer to the next schedule data
	structure.

the 'qtd' will be linked into qh hardware queue after the line
below

	*dummy = *qtd;

is executed and observed by EHCI HC, but EHCI HC won't have chance to
fetch the qtd descriptor pointed by 'qtd' in qh_append_tds until the
line below

	dummy->hw_token = token;	#set Active bit here

is executed by CPU and observed by EHCI HC.

There is already one 'wmb' to order writing to 'dummy'/'qtd' descriptors
and writing 'token' to 'dummy' descriptor(set Active bit), so the 1st
wmb is not needed and can be removed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI_SHRINK_JIFFIES should be 5ms, which was just used originally,
and not 200ms, so fix it.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Obviously, ZLP is only required for transfer of OUT direction,
so just take same policy with UHCI for ZLP packet.
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

qh_refresh is always called when the qh is idle and has not been
linked into hardware queue, so EHCI will not access overlay of
the qh at this time. Just before linking qh into hardware queue, there
has already one wmb to order writing qh descriptor and writing dma
address of the qh into hardware queue, so HC can always see
up-to-date qh descriptor once the qh is fetched with its dma address
by EHCI.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

here is the patch to support Owen SI-30 device.
This is a pulse counter controller.
http://www.owen.ru/en/catalog/93788515

usb-drivers output:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=03eb ProdID=0030 Rev=01.01
C:  #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=00 Driver=cdc_acm
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm

This patch is installed on my home system which receives data from this
controller connected to cold water counter.
Signed-off-by: NDenis Pershin <dyp@perchine.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A typo in the configuration variable name prevents from activating the
USB autosuspend on the device.
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The allocated chardevice region range is only 1 device but on
unregister it currently tries to deregister 2.

Found this while doing a insmod/rmmod/insmod/rm... of the module
which seemed to eat major numbers.
Signed-off-by: NFabian Godehardt <fg@emlix.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When a transceiver is available use otg_set_power to submit
the target current to it.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In a few places in the kernel, the code prints
a human-readable USB device speed (eg. "high speed").
This involves a switch statement sometimes wrapped
around in ({ ... }) block leading to code repetition.

To mitigate this issue, this commit introduces
usb_speed_string() function, which returns
a human-readable name of provided speed.

It also changes a few places switch was used to use
this new function.  This changes a bit the way the
speed is printed in few instances at the same time
standardising it.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

IDs found in the Windows driver's ZTEusbnet.inf file from the
ZTE MF100 drivers (O2 UK).  Also fixes the ZTE MF626 device
since it really is distinct from the 4G Systems stick and
apparently needs the net interface blacklisted too, while
there's no indication (yet) that the 4G Systems stick does.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

That's what the blacklist is for...
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It's cleaner than the array stuff, and we're about to add a bunch
more blacklist entries.  Second, there are devices that need both
the sendsetup and the reserved interface blacklists, which the
current code can't accommodate.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>