FIFO1_DMA_ERR is set twice, the second should be FIFO2_DMA_ERR.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NRam Vepa <ram.vepa@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After 2.6.29, PPC no more admits passing NULL to the dev parameter of
the DMA API. The result is a BUG followed by solid lock-up when the 
mv643xx_eth driver brings an interface up. The following patch makes 
the driver work on my Pegasos again; it is mostly a search and replace 
of NULL by mp->dev->dev.parent in dma allocation/freeing/mapping/unmapping
functions.
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Acked-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the purposes of bonding is to allow for redundant links, and failover
correctly if the cable is pulled. If all the members of a bonded device have
no carrier present, the bonded device itself needs to report no carrier present
to user space so management tools (like routing daemons) can respond.

Bonding in 802.3ad mode does not work correctly for this because it incorrectly
chooses a link that is down as a possible aggregator.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mixing of normal and irq spinlocks results in the following lockdep messages
on bootup on IP32:

[...]
Sending DHCP requests .
======================================================
[ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
2.6.30-rc5-00164-g41baeef #30
------------------------------------------------------
swapper/1 [HC0[0]:SC0[1]:HE0:SE0] is trying to acquire:
 (&priv->meth_lock){+.+...}, at: [<ffffffff8026388c>] meth_tx+0x48/0x43c

and this task is already holding:
 (_xmit_ETHER#2){+.-...}, at: [<ffffffff802d3a00>] __qdisc_run+0x118/0x30c
which would create a new lock dependency:
 (_xmit_ETHER#2){+.-...} -> (&priv->meth_lock){+.+...}

but this new dependency connects a SOFTIRQ-irq-safe lock:
 (_xmit_ETHER#2){+.-...}
... which became SOFTIRQ-irq-safe at:
  [<ffffffff80061458>] __lock_acquire+0x784/0x1a14
  [<ffffffff800627e0>] lock_acquire+0xf8/0x150
  [<ffffffff800128d0>] _spin_lock+0x30/0x44
  [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
  [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
  [<ffffffff8003da5c>] __do_softirq+0xec/0x208
  [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
  [<ffffffff8003dda0>] irq_exit+0x54/0x9c
  [<ffffffff80004420>] ret_from_irq+0x0/0x4
  [<ffffffff80004720>] r4k_wait+0x20/0x40
  [<ffffffff80015418>] cpu_idle+0x30/0x60
  [<ffffffff804cd934>] start_kernel+0x3ec/0x404

to a SOFTIRQ-irq-unsafe lock:
 (&priv->meth_lock){+.+...}
... which became SOFTIRQ-irq-unsafe at:
...  [<ffffffff800614f8>] __lock_acquire+0x824/0x1a14
  [<ffffffff800627e0>] lock_acquire+0xf8/0x150
  [<ffffffff800128d0>] _spin_lock+0x30/0x44
  [<ffffffff80263f20>] meth_reset+0x118/0x2d8
  [<ffffffff8026424c>] meth_open+0x28/0x140
  [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
  [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
  [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
  [<ffffffff80012e68>] do_one_initcall+0x58/0x170
  [<ffffffff804cd190>] kernel_init+0x98/0x104
  [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18

other info that might help us debug this:

2 locks held by swapper/1:
 #0:  (rcu_read_lock){.+.+..}, at: [<ffffffff802c0954>] dev_queue_xmit+0x1e0/0x4b0
 #1:  (_xmit_ETHER#2){+.-...}, at: [<ffffffff802d3a00>] __qdisc_run+0x118/0x30c

the SOFTIRQ-irq-safe lock's dependencies:
-> (_xmit_ETHER#2){+.-...} ops: 0 {
   HARDIRQ-ON-W at:
                        [<ffffffff800614d0>] __lock_acquire+0x7fc/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                        [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                        [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                        [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                        [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                        [<ffffffff80004420>] ret_from_irq+0x0/0x4
                        [<ffffffff80004720>] r4k_wait+0x20/0x40
                        [<ffffffff80015418>] cpu_idle+0x30/0x60
                        [<ffffffff804cd934>] start_kernel+0x3ec/0x404
   IN-SOFTIRQ-W at:
                        [<ffffffff80061458>] __lock_acquire+0x784/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                        [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                        [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                        [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                        [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                        [<ffffffff80004420>] ret_from_irq+0x0/0x4
                        [<ffffffff80004720>] r4k_wait+0x20/0x40
                        [<ffffffff80015418>] cpu_idle+0x30/0x60
                        [<ffffffff804cd934>] start_kernel+0x3ec/0x404
   INITIAL USE at:
                       [<ffffffff80061570>] __lock_acquire+0x89c/0x1a14
                       [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                       [<ffffffff800128d0>] _spin_lock+0x30/0x44
                       [<ffffffff802d2b88>] dev_watchdog+0x70/0x398
                       [<ffffffff800433b8>] run_timer_softirq+0x1a8/0x248
                       [<ffffffff8003da5c>] __do_softirq+0xec/0x208
                       [<ffffffff8003dbd8>] do_softirq+0x60/0xe4
                       [<ffffffff8003dda0>] irq_exit+0x54/0x9c
                       [<ffffffff80004420>] ret_from_irq+0x0/0x4
                       [<ffffffff80004720>] r4k_wait+0x20/0x40
                       [<ffffffff80015418>] cpu_idle+0x30/0x60
                       [<ffffffff804cd934>] start_kernel+0x3ec/0x404
 }
 ... key      at: [<ffffffff80cf93f0>] netdev_xmit_lock_key+0x8/0x1c8

the SOFTIRQ-irq-unsafe lock's dependencies:
-> (&priv->meth_lock){+.+...} ops: 0 {
   HARDIRQ-ON-W at:
                        [<ffffffff800614d0>] __lock_acquire+0x7fc/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                        [<ffffffff8026424c>] meth_open+0x28/0x140
                        [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                        [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                        [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                        [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                        [<ffffffff804cd190>] kernel_init+0x98/0x104
                        [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
   SOFTIRQ-ON-W at:
                        [<ffffffff800614f8>] __lock_acquire+0x824/0x1a14
                        [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                        [<ffffffff800128d0>] _spin_lock+0x30/0x44
                        [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                        [<ffffffff8026424c>] meth_open+0x28/0x140
                        [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                        [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                        [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                        [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                        [<ffffffff804cd190>] kernel_init+0x98/0x104
                        [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
   INITIAL USE at:
                       [<ffffffff80061570>] __lock_acquire+0x89c/0x1a14
                       [<ffffffff800627e0>] lock_acquire+0xf8/0x150
                       [<ffffffff800128d0>] _spin_lock+0x30/0x44
                       [<ffffffff80263f20>] meth_reset+0x118/0x2d8
                       [<ffffffff8026424c>] meth_open+0x28/0x140
                       [<ffffffff802c1ae8>] dev_open+0xe0/0x18c
                       [<ffffffff802c1268>] dev_change_flags+0xd8/0x1d4
                       [<ffffffff804e7770>] ip_auto_config+0x1d4/0xf28
                       [<ffffffff80012e68>] do_one_initcall+0x58/0x170
                       [<ffffffff804cd190>] kernel_init+0x98/0x104
                       [<ffffffff8001520c>] kernel_thread_helper+0x10/0x18
 }
 ... key      at: [<ffffffff80cf6ce8>] __key.32424+0x0/0x8

stack backtrace:
Call Trace:
[<ffffffff8000ed0c>] dump_stack+0x8/0x34
[<ffffffff80060b74>] check_usage+0x470/0x4a0
[<ffffffff80060c34>] check_irq_usage+0x90/0x130
[<ffffffff80061f78>] __lock_acquire+0x12a4/0x1a14
[<ffffffff800627e0>] lock_acquire+0xf8/0x150
[<ffffffff80012a0c>] _spin_lock_irqsave+0x60/0x84
[<ffffffff8026388c>] meth_tx+0x48/0x43c
[<ffffffff802d3a38>] __qdisc_run+0x150/0x30c
[<ffffffff802c0aa8>] dev_queue_xmit+0x334/0x4b0
[<ffffffff804e7e6c>] ip_auto_config+0x8d0/0xf28
[<ffffffff80012e68>] do_one_initcall+0x58/0x170
[<ffffffff804cd190>] kernel_init+0x98/0x104
[<ffffffff8001520c>] kernel_thread_helper+0x10/0x18

..... timed out!
IP-Config: Retrying forever (NFS root)...
Sending DHCP requests ., OK
[...]

Fixed by converting all locks to irq locks.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Tested-by: NAndrew Randrianasulu <randrik_a@yahoo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Napi structures are being created each time we open a port, but when
the port is closed the napi structure is only disabled but not removed.
This bug caused hang while removing the driver.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Reported-by: NJonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The second IDE channel of version 6 PCB is not being registered anymore since
the commit 48c3c107 (ide: add struct ide_host
(take 3)).
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Impact: fix an oops which always triggers

ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack.  Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Processor idle power states C2 and C3 stop the TSC on many machines.
Linux recognizes this situation and marks the TSC as unstable:

Marking TSC unstable due to TSC halts in idle

But if those same machines are booted with "processor.max_cstate=1",
then there is no need to validate C2 and C3, and no need to
disable the TSC, which can be reliably used as a clocksource.
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>

A previous 2.6.30 patch, a71e4917,
(ACPI: idle: mark_tsc_unstable() at init-time, not run-time)
erroneously disabled the TSC on systems that did not actually
have valid deep C-states.

Move the check after the deep-C-states are validated,
via new helper, tsc_check_state(), hich replaces tsc_halts_in_c().
Signed-off-by: NLen Brown <len.brown@intel.com>
Acked-by: NVenkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NFrans Pop <elendil@planet.nl>

If the BIOS hands us an invalid throttling state,
write a valid state.

http://bugzilla.kernel.org/show_bug.cgi?id=13259Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Tested-by: NJames Ettle <theholyettlz@googlemail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Introduce module parameter processor.ignore_tpc.

Some laptops are shipped with buggy _TPC,
this module parameter is used to to disable the buggy support.

http://bugzilla.kernel.org/show_bug.cgi?id=13259Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Tested-by: NJames Ettle <theholyettlz@googlemail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

drivers/built-in.o: In function `intel_opregion_init':
(.text+0x9d540): undefined reference to `acpi_video_register'

http://bugzilla.kernel.org/show_bug.cgi?id=13165Signed-off-by: NLen Brown <len.brown@intel.com>

In 2.6.29,
31878dd8
"ACPI: remove BM_RLD access from idle entry path"
moved BM_RLD initialization to init-time from run time.

But we discovered that some BIOS do not restore BM_RLD
after suspend, causing device errors on C3 and C4
after resume.  So now the kernel restores BM_RLD.

http://bugzilla.kernel.org/show_bug.cgi?id=13032Signed-off-by: NLen Brown <len.brown@intel.com>

The BIOS bug workaround mistakenly got disabled
when we followed the ACPI specification more closely
by ignoring OS updates to that bit.

(The BIOS is supposed to update SCI_EN, not the OS)

http://bugzilla.kernel.org/show_bug.cgi?id=13289Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.

The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard.  Only then are the
characteristics reported to SCSI via the VPD B1 page.

This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever.  With no complaints so far.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For disks with 4KB sectors, report the correct block size and alignment
when filling out the READ CAPACITY(16) response.

This patch is based upon code from Matthew Wilcox' 4KB ATA tree.  I
fixed the bug I reported a while back caused by ATA and SCSI using
different approaches to describing the alignment.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The bit 11 of command description is reserved bit in Freescale
SATA controller and needs to be set to '1'.  This is needed to
make sure the last write from the controller to the buffer
descriptor is seen before an interrupt is raised.
Signed-off-by: NDave Liu <daveliu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

We we build with dma_addr_t as a 64-bit quantity we get:

drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:340: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Issuing ATA_CMD_SET_FEATURES (0xef) times out because
pdc20621_interrupt ignores command completion since
ATA_TFLAG_POLLING flag is set.

This has already been fixed for sata_promise:

commit 51b94d2a
Author: Tejun Heo <htejun@gmail.com>
Date:   Fri Jun 8 13:46:55 2007 -0700

    sata_promise: use TF interface for polling NODATA commands

Also, this patch includes Mikael's original patches:

http://marc.info/?l=linux-ide&m=121135828227724&w=2
http://marc.info/?l=linux-ide&m=121144512109826&w=2Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NDavid Milburn <dmilburn@redhat.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 79e53945 introduced a
regression where you cannot use sysrq 'g' to enter kgdb.  The solution
is to move the intel fb sysrq over to V for video instead of G for
graphics.  The SMP VOYAGER code to register for the sysrq-v is not
anywhere to be found in the mainline kernel, so the comments in the
code were cleaned up as well.

This patch also cleans up the sysrq definitions for kgdb to make it
generic for the kernel debugger, such that the sysrq 'g' can be used
in the future to enter a gdbstub or another kernel debugger.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

The receive interrupt routine checks the wrong register if the
receive fifo is empty. Further an explicit interrupt acknowledge
write is introduced. In some circumstances another interrupt was
issued.
Signed-off-by: NBenjamin Krill <ben@codiert.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When the i2400m receives data and the device indicates there has to be
reordering, we keep an sliding window implementation to sort the
packets before sending them to the network stack.

One of the "operations" that the device indicates is "queue a packet
and update the window start". When the queue is empty, this is
equivalent to "deliver the packet and update the window start".

That case was optimized in i2400m_roq_queue_update_ws() so that we
would not pointlessly queue and dequeue a packet. However, when the
optimization was active, it wasn't updating the window start. That
caused the reorder management code to get confused later on with what
seemed to be wrong reorder requests from the device.

Thus the fix implemented is to do the right thing and update the
window start in both cases, when the queue is empty (and the
optimization is done) and when not.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

This allows userlevel code to discover the pipe number corresponding
to a given CRTC ID. This is necessary for doing pipe-specific
operations such as waiting for vblank on a given CRTC.  Failure to use
the right pipe mapping can result in GPU hangs, or at least failure
to actually sync to vblank.
Signed-off-by: NCarl Worth <cworth@cworth.org>
[anholt: Style touchups from review]
Signed-off-by: NEric Anholt <eric@anholt.net>

We detect HDMI output connection status by writing to HOT Plug Interrupt
Detect Enable bit in PORT_HOTPLUG_EN.  The behavior will generate a specified
interrupt, which is caught by audio driver, but during one detection driver
set all Detect Enable bits of HDMIB, HDMIC HDMID, and generate wrong
interrupt signals for current output, according to the signals audio driver
misunderstand device status. The patch intends to handle corresponding
output precisely.

It fixed freedesktop.org bug #21371
Signed-off-by: NMa Ling <ling.ma@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

It fixed bug #21659
Signed-off-by: NMa Ling <ling.ma@intel.com>
[anholt: hand-applied because git-am is too picky]
Signed-off-by: NEric Anholt <eric@anholt.net>

Although spec say CRT_HOTPLUG_ACTIVATION_PERIOD_64 is only useful for
mobile platform, it is also required to detect vga on G4x desktops correctly.
Tested on G45/G43/Q45 platforms with no regressions.

It fixed freedesktop.org bug #21120 and part of bug #21210
Signed-off-by: NMa Ling <ling.ma@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

There are a number of small form factor desktop systems with Intel mobile
graphics chips that lie and say they have an LVDS. With kernel mode-setting,
this becomes a problem, and makes native resolution boot go haywire -- for
example, my Dell Studio Hybrid, hooked to a 1920x1080 display claims to
have a 1024x768 LVDS, and the resulting graphical boot on the 1920x1080
display uses only the top left 1024x768, and auto-configured X will end
up only 1024x768 as well. With this change, graphical boot and X
both do 1920x1080 as expected.

Note that we're simply embracing and extending the early bail-out code
in place for the Mac Mini here. The xorg intel driver uses pci subsystem
device and vendor id for matching, while we're using dmi lookups here.
The MSI addition is courtesy of and tested by Bill Nottingham.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Tested-by: NBill Nottingham <notting@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

We might sleep here anyway so I hope an extra uncached read is ok to
add.

In #20896 we found that vbetool clobbers the IER.  In KMS mode this is
particularly bad since we don't set the interrupt regs late (in
EnterVT), so we'd fail to get *any* interrupts at all after X started
(since some distros have scripts that call vbetool at X startup
apparently).

So this patch checks IER at wait_request time, and re-enables
interrupts if it's been clobbered.  In a proper config this check
should never be triggered.

This is really a distro issue, but having a sanity check is nice, as
long as it doesn't have a real performance hit.
Tested-by: NMateusz Kaduk <mateusz.kaduk@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Moved the check inside of the sleeping case to avoid perf cost]
Signed-off-by: NEric Anholt <eric@anholt.net>

In IGD, DPCUNIT_CLOCK_GATE_DISABLE bit should be set, otherwise i2c
access will be wrong.

v2: Disable CLOCK_GATE_DISABLE bit after bit bashing as suggested by Eric.
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

This should avoid a class of bugs where the hardware prefetches past the
end of the object, and walks into unallocated memory when the object is
bound to the last page of the aperture.

fd.o bug #21488
Signed-off-by: NEric Anholt <eric@anholt.net>

This patch fixes a regression caused by commit
b1569e99
"ACPI: move thermal trip handling to generic thermal layer"
which accidentally changed trip point trigger condition to
  temp > trip_temp

This patch changes the trigger condition back to
  temp >= trip_temp
Signed-off-by: NVladimir Zajac <eightgraph@gmail.com>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Acked-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

If there is a failure during eeepc_hotk_add() we need
to remove the acpi_notify_handler.
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

KEY_STOP is now KEY_STOPCD
 It's the correct key to stop a media
BTN_EXTRA is now KEY_SCREENLOCK:
 The laptop manual tells us that this key is for screenlock
KEY_TV is now KEY_PROG1
 So it can be reported to X server

Ref: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/361505Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

The older eeepc-acpi driver allowed to control the SHE performance
preset through a ACPI function for just this purpose. SHE underclocks
and undervolts the FSB and undervolts the CPU (at preset 2,
"powersave"), or slightly overclocks the CPU (at preset 0,
"performance"). Preset 1 is the default setting with default clocks and
voltage.

The new eeepc-laptop driver doesn't support it anymore.
The attached patch adds support for it to eeepc-laptop. It's very
straight-forward and almost trivial.
Signed-off-by: NGrigori Goronzy <greg@chown.ath.cx>
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

1) Buggy firmware can change the RFKILL state by itself. This is easily
   detected.  The RFKILL API states that in such cases, we should call
   rfkill_force_state() to notify the core.

   I have reported the bug to Asus. I believe this is the right thing
   to do for robustness, even if this particular firmware bug is fixed.

2) The same bug causes the wireless toggle key to be reported as 0x11
   instead of 0x10.  0x11 is otherwise unused, so it should be safe to
   add this as a new keycode.

The bug is triggered by removing the laptop battery while hibernated.

On resume, the wireless toggle key causes the firmware to toggle the
wireless state itself.  (Also, the key is reported as 0x11 when the
current wireless state is OFF).

This is very poor behaviour because the OS can't predict whether the
firmware is controlling the RFKILL state.

Without this workaround, the bug means users have to press the wireless
toggle key twice to enable, due to the OS/firmware conflict.  (Assuming
rfkill-input or equivalent is being used).  The workaround avoids this.

I believe that acpid scripts which toggle the value of the sysfs state file
when the toggle key is pressed will be rendered ineffective by the bug,
regardless of this workaround.  If they simply toggle the state, when the
firmware has already toggled it, then you will never see a state change.

Tested on "EEEPC 4G" only.
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

This maps the brightness control events to one of two keys, either
KEY_BRIGHTNESSDOWN or KEY_BRIGHTNESSUP, as needed.

Some mapping has to be done due to the fact that the BIOS reports them as
<base value> + <current brightness index>; the selection is done according to
the sign of the change in brightness (if this is 0, no keypress is reported).

(Ref. http://lists.alioth.debian.org/pipermail/debian-eeepc-devel/2009-April/002001.html)
Signed-off-by: NDarren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

When an rfkill device is registered, the rfkill core will change its
state to the system default. So we need to prepare for state changes
*before* we register it. That means installing the eeepc-specific ACPI
callback which handles the hotplug of the wireless network adaptor.

This problem doesn't occur during normal operation.  You have to

1) Boot with wireless enabled. eeepc-laptop should load automatically.
2) modprobe -r eeepc-laptop
3) modprobe eeepc-laptop

On boot, the default rfkill state will be set to enabled.
With the current core code, step 2) will disable the wireless.
Therefore in step 3), the wireless will change state during registration,
from disabled to enabled.  But without this fix, the PCI device for the
wireless adaptor will not appear.
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NCorentin Chary <corentincj@iksaif.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

The following symbols are needlessly defined global:

default_mode
default_var
gbe_mem_phys
gbe_turn_off
gbefb_exit
gbefb_init
gbefb_setup

This error was noticed by namespacecheck when compiling ip32_defconfig.

This patch makes the symbols static.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>