Due to hardware limitations on BYT, MIPI Port C DPI Enable bit
does not get set. To check whether DSI Port C was enabled in BIOS,
check the Pipe B enable bit for DSI Port C. In hardware, DSI Port C
is linked with Pipe B.

v2: Addressed review comments of Jani, Nikula
    - Used platform checks for this software workaround for BYT
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Common bit to be used for both DSI Port A & DSI Port C.
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to program both port registers during dual link enable path.

v2: Address review comments by Jani
    - Used a for loop instead of do-while loop.

v3: Used for_each_dsi_port macro instead of for loop

v4: Renamed mode_hactive variable to mode_hdisplay
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to program both port registers during dual link disable path.

v2: Address review comments by Jani
    - Used a for loop instead of do-while loop.

v3: Used for_each_dsi_port macro instead of for loop

v4: Added comments for the usage of AFE latchout bit
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

hactive, hfp, hbp, hsync needs to be halved for dual link MIPI Panels.
Accordingly timing related mmio regs needs to be programmed for both MIPI Ports.

v2: Address review comments by Jani
    - Used a for loop instead of do-while loop

v3: Used for_each_dsi_port macro instead of for loop
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.

v2 : Address review comments by Jani
     - Removed the bit mask used for ->dual_link
     - Used DSI instead of MIPI for #define variables

v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For Dual Link MIPI Panels, both Port A and Port C should be enabled
during the MIPI encoder enabling sequence. Similarly, during the
disabling sequence, both ports needs to be disabled.

v2: Used for_each_dsi_port macro instead of for loop

v3: Used intel_dsi->ports instead of dual_link var for dual link configuration check

v4: Masking of the required MIPI port bits before writing proper values
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch is in preparation for the DSI dual link
port enable and disable related changes.
Signed-off-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Later on this can include multiple ports (e.g. (1 << PORT_A) | (1 <<
PORT_C)) to describe dual link DSI.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

MIPI DSI works on ports A and C, which map to pipes A and B,
respectively. Things are going to get more complicated with the
introduction of dual link DSI support, so clean up the register defines
and code to match reality.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NGaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

- fini goes with init, so call it intel_power_domains_fini. While
  at it shovel some of the fini code that leaked out of it back in.

- give power_enabled functions the verb _is_ to make the meaning clearer.
  Also use a __ prefix instead of _unlocked to really discourage users.

- rename runtime_pm_init/fini to enable/disable since that's what they do.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I'm not really that insisting on checkpath compliance, but ragged
function paramter alignment does get me. Please adjust your editor to
just do this for you.

Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Updated the error log as suggested by Imre
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.

Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly

v2: Address review comments by Daniel
    - Check if DPLL is enabled rather than checking pipe output type
    - set adjusted_mode->flags to 0 in compute_config rather than using
      pipe_config->quirks
    - Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
    - updated dpll_hw_state correctly
    - Updated commit message and title

v3: Address review comments by Imre
    - Proper masking of P1, M1 fields while computing divisors
    - assert in case of bpp mismatch
    - guard for divide by 0 while computing pclk
    - Use ARRAY_SIZE instead of direct calculation
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ensure that the DSI packets for a particular sequence are completely
sent before going ahead in the enabling or disabling of the panel
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We should keep DEVICE_READY bit set in the ULPS enter sequence. In
exit sequence also we should set DEVICE_READY, but thats causing
blankout for me. Also exit sequence is simplified as per hw team
recommendation.

This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: NThomas Wood <thomas.wood@intel.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_dsi_init() bails out without freeing the memory 'intel_dsi' and
'intel_connector' point to. Simply bail out before allocating memory.

Picked up by Coverity - CID 1222750.
Signed-off-by: NChristoph Jaeger <christophjaeger@linux.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Functions that can't fail are such a bliss to work with, it'd be shame
to miss the occasion. The "failure" mode is the DSI connector not being
created, the rest of the initialization can carry on happily.

We weren't even checking that value anyway.
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: NShobhit Kumar <shobhit.kumar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Also convert the missed return statement due to other patches
merged meanwhile.]
[danvet2: Squash in fixup from Damien to remove empty return; at the
end of intel_dsi_init.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we disable first the port (by disabling DPI) and only then the
display pipe the pipe-off flag will never be set, possibly leading to a
hanged pipe state at the next modeset-enable.

Note that according to the VLV2 display cluster HAS, we should disable
the port before the pipe. This doesn't seem to match reality based on
the above and it's also asymmetric with the enabling sequence, where we
first enable the port and then the pipe.

v2:
- send the panel shutdown command before stopping the pipe, since this
  is the recommended sequence (Shobhit)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It seems by default the VBT has MIPI configuration block as well. The
Generic driver will assume always MIPI if MIPI configuration block is found.
This is causing probelm when actually there is eDP. Fix this by looking
into general definition block which will have device configurations. From here
we can figure out what is the LFP type and initialize MIPI only if MIPI
is found.

v2: Addressed review comments by Damien
    - Moved PORT definitions to intel_bios.h and renamed as DVO_PORT_MIPIA
    - renamed is_mipi to has_mipi and moved definition as suggested
    - Check has_mipi inside parse_mipi and intel_dsi_init insted of outside

v3: Make has_mipi as a bitfield as suggested
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: fold in conditions to pack everything neatly below 80 chars.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This driver makes use of the generic panel information from the VBT.
Panel information is classified into two - panel configuration and panel
power sequence which is unique to each panel. The generic driver uses the
panel configuration and sequence parsed from VBT block #52 and #53

v2: Address review comments by Jani
    - Move all of the things in driver c file from header
    - Make all functions static
    - Make use of video/mipi_display.c instead of redefining
    - Null checks during sequence execution

v3: Address review comments by Damien
    - Rename the panel driver file as intel_dsi_panel_vbt.c
    - Fix style changes as suggested
    - Correct comments for lp->hs and hs->lp count calculations
    - General updating comments to have more clarity
    - using max() instead of ternary operator
    - Fix names (ui_num, ui_den) while using UI in calculations
    - compute max of lp_to_hs switch and hs_to_lp switch while computing
      hs_lp_switch_count
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch adds a mmio base address variable for DSI display,
to make the DSI code generic, so that, if required, the same code
can be re-used for future platforms with different mmio base.
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Looking at our current dsi driver I note that:
- We don't have any slave driver right now.
- There's zero support for the hardware state readout and cross check
  code.
- All the modeset state seems to be tracked in the intel_dsi structure
  instead of the pipe config.

Given all that I can't properly audit the dsi ->mode_set callback. So
just do it as the first thing in the ->pre_pll_enable hook and hope
for the best.
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added as generic parameters which will be initialized in the panel
driver and are specific to panels.

Backlight delays have also kept as placeholders and will be used used
once we have MIPI backlight enabling support
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In VBT fields operation mode is 0 for Video mode and 1 for command mode.
This field will be directly used as is in generic panel driver. So
adjust accordingly.
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some MIPI panels might not have resolution which is a multiple of 64 like
1366x768. Enable this feature for such panels by default
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Though HS mode also should work.

v2: Change parameter as "bool hs" as suggested by Jani
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In preparation for Generic driver
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise, this can stall pipe. We also need DPLL REFA always
enabled
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As per the hw team's recommendation we need to enable the MIPI port
before enabling the plane and pipe. So call MIPI port enable in
pre_enable phase itself
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently we allow encoders to indicate whether they can be part of a
cloned set with just one flag. That's not flexible enough to describe
the actual hardware capabilities. Instead make it a bitmask of encoder
types with which the current encoder can be cloned.

For now we set the bitmask to allow DVO+DVO and DVO+VGA, which should
match what the old boolean flag allowed. We will add some more cloning
options in the future.

Note that this patch also removes the encoder.possible_clones setting
from encoder setup code - we compute this dynamically.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add Ville's explanation why removing the encoder
possible_clones is save.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since the encoder is tied to its port, we need to make sure the power
domain for that port is on before reading out the encoder HW state.

Note that this also covers also all connector get_hw_state handlers,
since all those just call the corresponding encoder get_hw_state
handler, which checks - after this change - for all power domains
the connector needs.

v2:
- no change
v3:
- push down the power domain checks into the specific encoder
  get_hw_state handlers (Daniel)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The connector detect and get_mode handlers need to access the port
specific HW blocks to read the EDID etc. Get/put the port power domains
around these handlers.

v2:
- get port power domain for HDMI too (Ville)
- get port power domain for the DP,HDMI audio detect handlers (Jesse)
- Leave the intel_runtime_pm_get/put in the DP detect function in place.
  Instead of just removing them, these should be moved to the appropriate
  power_well enable/disable handlers. We can do this after Paulo's
  'Merge PC8 with runtime PM, v2' patchset.
v3:
- rebased on latest -nightly
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since

commit d9255d57
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Thu Sep 26 20:05:59 2013 -0300

it became clear that we need to separate the unload sequence into two
parts:

1. remove all interfaces through which new operations on some object
   (crtc, encoder, connector) can be started and make sure all pending
   operations are completed
2. do the actual tear down of the internal representation of the above
   objects

The above commit achieved this separation for connectors by splitting
out the sysfs removal part from the connector's destroy callback and
doing this removal before calling drm_mode_config_cleanup() which does
the actual tear-down of all the drm objects.

Since we'll have to customize the interface removal part for different
types of connectors in the upcoming patches, add a new unregister
callback and move the interface removal part to it.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NAntti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of modifying intel_panel in lvds_init_connector/dsi_init/
edp_init_connector, making changes to move intel_panel->downclock_mode
initialization to intel_panel_init()

v2: Jani's review comments incorporated
Removed downclock_mode local variable in dsi_init and
edp_init_connector
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NPradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The values of these parameters will be different for differnet panel
based on dsi rate, lane count, etc. Remove the hardcodings and make
these as parameters whch will be initialized in panel specific
sub-encoder implementaion.

This will also form groundwork for planned generic panel sub-encoder
implemntation based on VBT design enhancments to support multiple panels

v2: Mask away the port_bits before use
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>