Add iomux, clocks,  and memory map for Freescale's MX53 SoC.
Add cpu_is_mx53 function to common.h.
Add 3 more banks of gpio's to mxc_gpio_ports.
Add MX53 phys offset address.
Signed-off-by: NDinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

There's no point showing this option to the user. The correct
value will be selected anyway.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds a Kconfig option for the avic irq controller
and lets the SoCs that need it select this option.
Also, as we have two irq controllers for i.MX, irq.c is not
appropriate anymore, so rename it to avic.c
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Commit "ARM: i.MX IOMUX-V3 replace struct pad_desc with bitmapped cookie"
(b705cb4d42e95a4a43a8945571c8613e71526c3d) introduced a typo which was
preventing my efikamx to boot. This patch is fixing that.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The efikamx board is using a gpio to reset the board so add support
for it
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

s/NO_PAD_CTRL/MX51_GPIO_PAD_CTRL/
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add definitions for configuring CSI1_{H,V}SYNC as GPIO
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

- add definition to configure pads as ESDHC{1,2} WP and CD
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

- ALT0 is used to set GPIO mode of GPIO_1_{2,3,4,5,6,7,8,9} but it's ALT1
for GPIO_1_{0,1}.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The following patch is a first step to convert the 'struct pad_desc'
to a bitmapped cookie to facilitate adding platform specific pullup or
drive strength definitions to existing pad definitions without need to
rewrite the complete pad def.

The patch wraps 'struct pad_desc' in an opaque data type and
introduces macros to access the individual members.
This patch does not constitute any functional change!
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

and restore alphabetic ordering.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

While adapting the #defines for this I noticed that the offset
used for USB HS on i.MX35 differs from the documented offset.
I kept the working offset and commented that the documentation
differs.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Compared to the static devices the dynamic have a DMA resource.
This should be save as it seems unused in the driver.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Additionally convert some known to be good usages to the new
names.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Some usages of ARCH_MX25 are assuming that if it is
defined the other SoCs are undefined.  Use SOC_IMX25 for the save
places.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This way FB_IMX can just depend on HAVE_FB_IMX and machines
just need to select IMX_HAVE_PLATFORM_IMX_FB without bothering
about HAVE_FB_IMX.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

The mxc-keypad device seems to be the result of an early and partial
merge of the keypad driver.  It's unused and there is no corresponding
driver available, so just remove it.

Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

To use common macros to define the gpio ports for imx{1,21,25,27} the
existing ones had to made more general and a few more base address defines
were necessary.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

According to the reference manual of the i.MX25 the host controller uses an
offset of 0x200 not 0x400 as was specified in the resources for mxc_usbh2.

Needs-Testing: yes
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

This finally gets rid of mach-imx/devices.c.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

... plus a trivial simplification of mx21ads_sdhc_init()
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

Group soc specific data in a global struct instead of repeating it for each
call to imxXX_add_flexcanX.  The structs holding the actual data are placed
in .init.constdata and so don't do much harm.  Compared to the previous
approach this reduces code size to call imx_add_flexcan.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>