Callers expect pci_user_{read,write}_config_*() to indicate errors by
returning negative values.  Prior to this change, the indicated routines
could return positive error codes (e.g. PCIBIOS_BAD_REGISTER_NUMBER)
which callers would mistakenly interpret as success.

This change converts any non-zero return from the mentioned routines
into unambiguous negative value return codes.
Signed-off-by: NGreg Thelen <gthelen@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

pci_vpd_pci22_write() calls pci_vpd_pci22_wait() after writing
PCI_VPD_DATA and PCI_VPD_ADDR to wait for the VPD operation to complete.
The result pci_vpd_pci22_wait() was not checked for error.

This change checks for error.
Signed-off-by: NGreg Thelen <gthelen@google.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

We were just lucky that ICH4_GPIO_EN and ICH6_GPIO_EN happen to have
the same value.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

TI816X (common name for DM816x/C6A816x/AM389x family) devices configured
to boot as PCIe Endpoint have class code = 0. This makes kernel PCI bus
code to skip allocating BARs to these devices resulting into following
type of error when trying to enable them:

"Device 0000:01:00.0 not available because of resource collisions"

The device cannot be operated because of the above issue.

This patch adds a ID specific (TI VENDOR ID and 816X DEVICE ID based)
'early' fixup quirk to replace class code with
PCI_CLASS_MULTIMEDIA_VIDEO as class.
Signed-off-by: NHemant Pedanekar <hemantp@ti.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

If it was preempted, and the variable aer_mask_override is changed
after the spin_unlock_irqrestore it will write an uninitialized
variable by the pci_write_config_dword() function.
Signed-off-by: NWanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The pci_pm_reset() function is not a very nice interface due to its
limitations and conditional behavior (e.g. it doesn't affect devices
in low-power states), but it cannot be simply dropped, because
existing device drivers may depend on it.  However, its behavior and
limitations should be well documented, so add an appropriate
kerneldoc comment to it.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Commit 2f671e2d allowed us to clear ASPM state when the FADT
tells us it isn't supported, but we don't put this into effect
if the aspm_policy is set to POLICY_POWERSAVE.  Enable the
state to be cleared regardless of policy.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Prefer min m to max p only on pre-r7xx asics.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36197Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Commit 73412c38 ("drm/nouveau: allocate
kernel's notifier object at end of block") intended to align end of
notifier block to page boundary, but start of block was miscalculated
to be off by -16 bytes. Fix it.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

nouveau_bo_wr32 expects offset to be in words, but we pass value in bytes,
so after commit 73412c38 ("drm/nouveau: allocate
kernel's notifier object at end of block") we started to overwrite some memory
after notifier buffer object (previously m2mf_ntfy was always 0, so it didn't
matter it was a value in bytes).
Reported-by: NDominik Brodowski <linux@dominikbrodowski.net>
Reported-by: NNigel Cunningham <lkml@nigelcunningham.com.au>
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Pekka Paalanen <pq@iki.fi>
Cc: stable@kernel.org    [2.6.38]
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Problem introduced with commit 6ba9a683Reported-by: NBob Gleitsmann <rjgleits@bellsouth.net>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Caught with kmemcheck on unrelated business.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Wasn't aware they even existed, apparently they do!  They're actually
AGP chips with a bridge as far as I can tell, which puts them in the
same boat as nv40/nv45.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fixes a possible lock ordering reversal between context_switch_lock
and ramin_lock.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Reviewed-by: NFrancisco Jerez <currojerez@riseup.net>

This reverts commit 35d9f510.

Quoth Jiri Slaby:
 "It fixes mmap when IOMMU is used on x86 only, but breaks architectures
  like ARM or PPC where virt_to_phys(dma_alloc_coherent) doesn't work.
  We need there dma_mmap_coherent or similar (the trickery what
  snd_pcm_default_mmap does but in some saner way).  But this cannot be
  done at this phase."
Requested-by: NJiri Slaby <jslaby@suse.cz>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Mouse gets "stuck" after restore of PV guest but buttons are in working
condition.

If driver has been configured for ABS coordinates at start it will get
XENKBD_TYPE_POS events and then suddenly after restore it'll start getting
XENKBD_TYPE_MOTION events, that will be dropped later and they won't get
into user-space.

Regression was introduced by hunk 5 and 6 of
5ea5254aa0ad269cfbd2875c973ef25ab5b5e9db
("Input: xen-kbdfront - advertise either absolute or relative
coordinates").

Driver on restore should ask xen for request-abs-pointer again if it is
available. So restore parts that did it before 5ea5254.
Acked-by: NOlaf Hering <olaf@aepfle.de>
Signed-off-by: NIgor Mammedov <imammedo@redhat.com>
[v1: Expanded the commit description]
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Calculate a default based on the number of ABS axes, REL axes,
and MT slots for the device during input device registration.
Signed-off-by: NJeff Brown <jeffbrown@android.com>
Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly.  I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

In omap_rtc_probe error path, free_irq() was using NULL rather than the
driver data as the data pointer so free_irq() wouldn't have matched.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: "George G. Davis" <gdavis@mvista.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Link: http://lkml.kernel.org/r/%3C1303005778.2889.2.camel%40phoenix%3ESigned-off-by: NThomas Gleixner <tglx@linutronix.de>

We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.

Also remove some plug-related code that is no longer needed.
Signed-off-by: NNeilBrown <neilb@suse.de>

In raid5 plugging is used for 2 things:
 1/ collecting writes that require a bitmap update
 2/ collecting writes in the hope that we can create full
    stripes - or at least more-full.

We now release these different sets of stripes when plug_cnt
is zero.

Also in make_request, we call mddev_check_plug to hopefully increase
plug_cnt, and wake up the thread at the end if plugging wasn't
achieved for some reason.
Signed-off-by: NNeilBrown <neilb@suse.de>

When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.

If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
Signed-off-by: NNeilBrown <neilb@suse.de>

md has some plugging infrastructure for RAID5 to use because the
normal plugging infrastructure required a 'request_queue', and when
called from dm, RAID5 doesn't have one of those available.

This relied on the ->unplug_fn callback which doesn't exist any more.

So remove all of that code, both in md and raid5.  Subsequent patches
with restore the plugging functionality.
Signed-off-by: NNeilBrown <neilb@suse.de>

Now that unplugging is done differently, the unplug_fn callback is
never called, so it can be completely discarded.
Signed-off-by: NNeilBrown <neilb@suse.de>

md/raid submits a lot of IO from the various raid threads.
So adding start/finish plug calls to those so that some
plugging happens.
Signed-off-by: NNeilBrown <neilb@suse.de>

Several tests in the ipv6 routing code check IFF_LOOPBACK, and
allowing stacking such as VLAN'ing on top of loopback results in a
netdevice which reports IFF_LOOPBACK but really isn't the loopback
device.

Instead of spamming the ipv6 routing code with even more special tests,
simply disallow VLAN over loopback.

The result of this patch is:

# modprobe 8021q
# vconfig add lo 43
ERROR: trying to add VLAN #43 to IF -:lo:-  error: Operation not supported
Signed-off-by: NKrishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes port identification on optic devices when there's no link on the port.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apparently some distros set i2c-algo-bit.bit_test to 1 by
default.  In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added.  In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails.  This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36221Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [.38 down to .34]

When warning on the use of deprecated i2c_driver methods
attach_adapter and detach_adapter, mention the name of the driver
which needs to be updated.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch fixes two issues:
- A disabled crtc does not use any lb, so return 0 for
lb size.  This makes the display priority calculation
more exact.
- Only use 1/2 and whole lb partitions. Using smaller
partitions can cause underflow to one of the displays
if you have multiple large displays on the same lb.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=34534Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error.  Abort mport initialization if
registration failed.

This patch is applicable to 2.6.39-rc1 only.  The problem does not exist
for earlier versions.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the wrong members and the wrong function's definition, since the
irq_chip had changed.
Signed-off-by: NWanlong Gao <wanlong.gao@gmail.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the driver aware of the initial status of the regulator.

The leds-regulator driver was ignoring the initial status of the
regulator; this resulted in rdev->use_count being incremented to 2 after
calling regulator_led_set_value() in the .probe method when a regulator
was already enabled at insmod time, which made it impossible to ever
disable the regulator.
Signed-off-by: NAntonio Ospite <ospite@studenti.unina.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sometimes the i2c test in i2c_bit_add_bus fails
if this happens we fail to register the i2c adapter and
eventually fail to add the connector.  If i2c fails,
add the connector to the user can at least force
it on.

Note that some distros set i2c-algo-bit.bit_test to 1 by
default which sometimes fails preventing the ddc i2c adapter
from being added.  The i2c adapter works even if the bit test
fails, probably due to pre/post_xfer not getting called in
the test_bit function.  I have another patch to follow
up on that.

See:
https://bugs.freedesktop.org/show_bug.cgi?id=36221Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Noticed by Patrick Lowry.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

The memory leak was caused by unintentional assignment of the Rx path
destroy callback function pointer to NULL just after correct
initialization.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: NDebashis Dutt <ddutt@brocade.com>
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>