Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

helpers parallel to set_restore_sigmask(), used in the next commits
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Complete the move of sh64 to it, trim the crap from prototypes,
tidy up a bit.  Infrastructure in do_signal() had already been
there, in signal_64 as well as in signal_32 (where it was already
used).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Everything is using sparseirq these days, so we have no need to
arbitrarily size nr_irqs ahead of time. The legacy IRQ pre-allocation
likewise has no meaning for us, so that's killed off too. We now depend
on nr_irqs expansion by the generic hardirq layer instead.

It's also worth noting that the majority of boards had completely bogus
values for their nr_irqs relative to their CPU and configurations, so
this ends up correcting behaviour for quite a few platforms.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Attempt to "tidy" up some of the multi IRQ handling and base + IRQ
management. This should keep it limping along without too much hassle,
and no new parts should ever be enabling or using this API anyways.

It doesn't get any closer to lipstick on a pig as this.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We don't support the ISA DMA API, so this is only ever misused. The
dma-sh case inadvertently broke the dreamcast case by testing the wrong
variable for the total number of channels, so this fixes that up too.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This has turned in to quite a mess, and with CPUs that care using
dmaengine now it's about time to start cleaning up after the legacy DMA
code. For starters, kill off the stubs for the CPUs that don't do
anything, as well as all of the unused definitions. This leaves us with a
set of IRQs and base addresses we can deal with later.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

cpu-sh4a headers take priority over cpu-sh4 ones by virtue of the build
system, there's no need to try and mingle sh4a stuff in cpu-sh4.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This reverts commit 20e7c297.
With store queues enabled the area above P4SEG has special properties
from the MMU's point of view, which was causing fixmap failure. We'll
have to do something else to satisfy the vmalloc range check.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This converts over the legacy PCI IRQs to evt2irq() backed hwirq lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This migrates the cpu-family relative DMA IRQ definitions over to
evt2irq() backed hwirq lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Migrate sdk7780 to evt2irq backed hwirq lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Migrate landisk to evt2irq backed hwirq lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Migrate hp6xx to evt2irq backed hwirq lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Migrate Solution Engine boards to evt2irq backed hwirq lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Migrate edosk7760 to evt2irq() backed hwirq lookups.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.

Remove it and use the arch_dup_task_struct() instead.
Suggested-by: NOleg Nesterov <oleg@redhat.com>
Suggested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.comAcked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

This was reworked some time ago to go through fixmaps instead, leaving
the range itself unused. As such, kill off the remaining references and
hand over the remaining space for fixmaps directly. This also makes it
possible to simplify the vmalloc fault case as we no longer have to care
about the special section.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

At the moment the top of the fixmap space is calculated from P4SEG, which
places it at the end of the store queue space when that API is enabled.
Make sure we use P3_ADDR_MAX here instead to find the proper address
limit. With this done, it's also possible to switch to the generic
vmalloc address range check now that VMALLOC_START/END encapsulate the
translatable areas that we care about.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This provides a simple interface modelled after sparc64/m32r to encode
the error code in the upper byte of thread_info for finer-grained
handling in the page fault path.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We need a lookup_exception_vector() helper for sh64 in order to use the
common page fault code.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This follows the x86 changes for tidying up the page fault error paths.
We'll build on top of this for _32/_64 unification.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Too many drivers fail at IOPORT vs IOMEM checking before blindly calling
in to the API, so we may as well just provide basic stubs to get more
build coverage. Other platforms already do this, too (tile, parisc, etc.)
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is an sh2a device with FPU, video display controller (VDC),
8 serial ports, 3 I2C channels, 2 CAN ports, SD and on-chip USB.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The current code groups up to 16 nodes in a level and then puts an
ALLNODES domain spanning the entire tree on top of that. This doesn't
reflect the numa topology and esp for the smaller not-fully-connected
machines out there today this might make a difference.

Therefore, build a proper numa topology based on node_distance().

Since there's no fixed numa layers anymore, the static SD_NODE_INIT
and SD_ALLNODES_INIT aren't usable anymore, the new code tries to
construct something similar and scales some values either on the
number of cpus in the domain and/or the node_distance() ratio.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Anton Blanchard <anton@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-sh@vger.kernel.org
Cc: Matt Turner <mattst88@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: sparclinux@vger.kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Greg Pearson <greg.pearson@hp.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: bob.picco@oracle.com
Cc: chris.mason@oracle.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-r74n3n8hhuc2ynbrnp3vt954@git.kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>

The core now has a threadinfo allocator which uses a kmemcache when
THREAD_SIZE < PAGE_SIZE.

Deal with the xstate cleanup in the new arch_release_task_struct()
function.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/20120505150142.189348931@linutronix.de

We error out when compiling with gcc4.1.[01] as it miscompiles
__weak. The workaround with magic defines is not longer
necessary. Make it __weak again.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20120505150141.306358267@linutronix.de

cpuidle uses generic kick_all_cpus_sync() now. Remove the unused code.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/20120507175652.461648208@linutronix.de

With the introduction of static keys, anything using tracepoints blows up
in the following manner:

include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update')
include/trace/events/oom.h:8:13: error: initializer element is not constant
include/trace/events/oom.h:8:13: error: (near initialization for '__tracepoint_oom_score_adj_update.key')

This is a result of the STATIC_KEY_INIT_xxx defs wrapping ATOMIC_INIT()
which on sh includes an atomic_t typecast. Given that we don't really
need the typecast for anything anymore, the simplest solution is simply
to kill off the cast.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/20120420124557.855203626@linutronix.de

While the trap number and error code are passed around for debugging
purposes, this occurs wholly independently of the thread struct values.
These values were never part of the sigcontext ABI and are thus never
passed anywhere, so we can just kill them off across the board.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This implements basic -fstack-protector support, based on the early ARM
version in c743f380. The SMP case is
limited to the initial canary value, while the UP case handles per-task
granularity (limited to 32-bit sh until a new enough sh64 compiler
manifests itself).
Signed-off-by: NFilippo Arcidiacono <filippo.arcidiacono@st.com>
Reviewed-by: NCarmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This implements initial support for the SH7734.
This adds support SCIF, TMU and RTC.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Our SMP cache flush ops use CPU cross calls to deal with things
like I-cache accesses not being broadcast in hardware, so ensure that
the CACHE_FLUSH_IS_SAFE reflects this.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This updates sh following the generic kgdb changes adding support
for individual register get/set for kgdb/kdb use.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When a host stops or suspends a VM it will set a flag to show this.  The
watchdog will use these functions to determine if a softlockup is real, or the
result of a suspended VM.
Signed-off-by: NEric B Munson <emunson@mgebm.net>
asm-generic changes Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>