This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

It needs very similar workarounds to the one on BCM4707. It was tested
on D-Link DIR-885L home router.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chipsets with BCM4707 / BCM53018 ID require special handling at a few
places in the code. It's likely there will be more IDs to check in the
future. To simplify it add this trivial helper.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: f1640c3d ("bgmac: fix a missing check for build_skb")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when build_skb failed, it may occure a NULL pointer.
So add a 'NULL check' for it.
Signed-off-by: NWeidong Wang <wangweidong1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a5597008 ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:

drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'

Add the missing argument.
Reported-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom buses may have more than 1 Ethernet device. This is used e.g.
to have few interfaces connected to different switch ports. So far we
saw chipsets with only 2 devices (e.g. BCM4706) but recent ones have
up to 3 (e.g. Netgear R8000 uses 3rd interface for most of switch
traffic, lower interfaces are for some kind of offloading).
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After d75b1ade ("net: less interrupt masking in NAPI") polling
function has to return whole budget when it wants NAPI to call it again.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Fixes: eb64e292 ("bgmac: leave interrupts disabled as long as there is work to do")
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ring size is always known at compile time, so make the code a bit
more efficient
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver needs to inform the hardware about the first invalid (not yet
filled) rx slot, by writing its DMA descriptor pointer offset to the
BGMAC_DMA_RX_INDEX register.

This register was set to a value exceeding the rx ring size, effectively
allowing the hardware constant access to the full ring, regardless of
which slots are initialized.

To fix this issue, always mark the last filled rx slot as invalid.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of allocating buffers at device init time and initializing
descriptors at device open, do both at the same time (during open).
Free all buffers when closing the device.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In very rare cases, the MAC can catch an internal buffer that is bigger
than it's supposed to be. Instead of crashing the kernel, simply pass
the buffer back to the hardware
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate a new buffer before processing the completed one. If allocation
fails, reuse the old buffer.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A packet buffer offset of 30 bytes is inefficient, because the first 2
bytes end up in a different cacheline.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always poll rx and tx during NAPI poll instead of relying on the status
of the first interrupt. This prevents bgmac_poll from leaving unfinished
work around until the next IRQ.
In my tests this makes bridging/routing throughput under heavy load more
stable and ensures that no new IRQs arrive as long as bgmac_poll uses up
the entire budget.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep incrementing ring->start and ring->end instead of pointing it to
the actual ring slot entry. This simplifies the calculation of the
number of free slots.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two reasons for having this header in the common place:
1) Simplifying drivers that read NVRAM entries. We will be able to
   safely call bcm47xx_nvram_* functions without #ifdef-s.
2) Getting NVRAM driver out of MIPS arch code. This is needed to support
   BCM5301X arch which also requires this NVRAM driver. Patch for that
   will follow once we get is reviewed.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: linux-soc@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8619/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Always use software checksumming, since the hardware does not have any
checksum offload support.
This significantly improves local TCP tx performance.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This improves performance for routing and local rx
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ARM SoCs with bgmac Ethernet hardware we don't have any normal PHY.
There is always a switch attached but it's not even controlled over MDIO
like in case of MIPS devices.
We need a fixed PHY to be able to send/receive packets from the switch.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Northstar (Broadcom's ARM architecture) we need to manually enable
all cores. Code for that is already in place, but the condition for it
was wrong.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the normal {} instead of a macro to terminate an array.

Remove the macro too.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQs should only get activated when there is nothing to poll in the
queue any more and to after every poll.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

napi should get registered before the netdev and not after.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bgmac_mii_register() and register_netdev() both return appropriate error
codes for the failures they would encounter, propagate this error code
instead of overriding the value with -ENOTSUPP which is not the correct
error code to return.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes some typos found by Sergei.
Reported-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the Northstar SoC. This SoC does not have a PMU in
bcma and no register on it should be called. In addition it support 2.5
GBit/s Ethernet to the PHY.

This GMAC core is not fully working there are still problems with the
DMA controller.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Northstar SoC (BCM4707 and BCM53018) we have to enable all GMAC
cores when we just want to use on. We iterate over all the cores and
activate them.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BGMAC_CMDCFG_SR register is at a different position on core rev >= 4
We do not know where this register is on a rev 5 or higher core, I have
newer seen such a core.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DMA controller used in the device supported by GMAC with core rev
>= 4 has some new options which are now set to the default values used
in the Broadcom SDK.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This works pretty much the same way, so avoid duplicating the code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this bgmac_adjust_link didn't know it should re-initialize MAC
state. This led to the MAC not working after if down & up routine.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've realized that I need to call ethtool command to get Ethernet
working after booting. Ex call: ethtool -s eth0 autoneg on
It was fixing Ethernet even if auto-negotiation was already on.

Adding calls to phy_start and phy_stop look like a real solution.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were already registering MDIO bus, but we were not connecting bgmac
to the PHY. Add proper call and implement adjust link function to switch
MAC into requested state.
At the same time it's possible to drop our internal PHY management.
This is a "standard" PHY, so the "Generic PHY" driver works perfectly
fine with this. Don't duplicate the code.
Finally make use of phy_ethtool_[gs]set functions instead implementing
them from scratch.

This change was successfully tested on BCM5357. I was able to
autonegotiate 1000Mb/s full duplex, as well as force any of the
10/100/1000 half/full modes.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Copying whole packets with skb_copy_from_linear_data_offset is a pretty
bad idea. CPU was spending time in __copy_user_common and network
performance was lower. With the new solution iperf-measured speed
increased from 116Mb/s to 134Mb/s.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>