Implement devlink show and set of HW inline-mode.
The supported modes: none, link, network, transport.
We currently support one mode for all vports so set is done on all vports.
When eswitch is first initialized the inline-mode is queried from the FW.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also move the inline capablities enum to a shared header vport.h
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.

The supported modes: none, link, network, transport.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reflect the administative link changes done on the VF representor to the
VF e-switch vport. This means that doing ip link set down/up commands on
the VF rep will modify the e-switch vport state which in turn will make
proper VF drivers to set their carrier accordingly.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switchdev driver net-device port statistics should follow the model introduced
in commit a5ea31f5 'Merge branch net-offloaded-stats'.

For VF reps we return the SRIOV eswitch vport stats as the usual ones and SW stats
if asked. For the PF, if we're in the switchdev mode, we return the uplink stats
and SW stats if asked, otherwise as before. The uplink stats are implemented using
the PPCNT 802_3 counters which are already being read/cached by the driver.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: broadcom: Wirespeed/downshift support

This patch series adds support for the Broadcom Wirespeed, aka
downsfhit feature utilizing the recently added ethtool PHY tunables.

Tested with two Gigabit link partners with a 4-wire cable having only
2 pairs connected.

Last patch in the series is a fix that was required for testing, which
should make it to -stable, which I can submit separate against net if
you prefer David.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.

Fixes: 450b05c1 ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 2331ccc5 ("tcp: enhance tcp collapsing"),
we made a first step allowing copying right skb to left skb head.

Since all skbs in socket write queue are headless (but possibly the very
first one), this strategy often does not work.

This patch extends tcp_collapse_retrans() to perform frag shifting,
thanks to skb_shift() helper.

This helper needs to not BUG on non headless skbs, as callers are ok
with that.

Tested:

Following packetdrill test now passes :

0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 8>
   +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
+.100 < . 1:1(0) ack 1 win 257
   +0 accept(3, ..., ...) = 4

   +0 setsockopt(4, SOL_TCP, TCP_NODELAY, [1], 4) = 0
   +0 write(4, ..., 200) = 200
   +0 > P. 1:201(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 201:401(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 401:601(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 601:801(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 801:1001(200) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1001:1101(100) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1101:1201(100) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1201:1301(100) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1301:1401(100) ack 1

+.099 < . 1:1(0) ack 201 win 257
+.001 < . 1:1(0) ack 201 win 257 <nop,nop,sack 1001:1401>
   +0 > P. 201:1001(800) ack 1
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: NStefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: NUwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VMware VMCI transport supports loopback inside virtual machines.
This patch implements loopback for virtio-vsock.

Flow control is handled by the virtio-vsock protocol as usual.  The
sending process stops transmitting on a connection when the peer's
receive buffer space is exhausted.

Cathy Avery <cavery@redhat.com> noticed this difference between VMCI and
virtio-vsock when a test case using loopback failed.  Although loopback
isn't the main point of AF_VSOCK, it is useful for testing and
virtio-vsock must match VMCI semantics so that userspace programs run
regardless of the underlying transport.

My understanding is that loopback is not supported on the host side with
VMCI.  Follow that by implementing it only in the guest driver, not the
vhost host driver.

Cc: Jorgen Hansen <jhansen@vmware.com>
Reported-by: NCathy Avery <cavery@redhat.com>
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All conflicts were simple overlapping changes except perhaps
for the Thunder driver.

That driver has a change_mtu method explicitly for sending
a message to the hardware.  If that fails it returns an
error.

Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.

However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:

drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]

This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.

Fixes: a0627f77 ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: core: Implement thermal zone

Implement thermal zone for mlxsw based HW.
The first patch is just a register dependency for the second patch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement thermal zone for mlxsw based HW. It uses temperature sensor
provided by ASIC (the same as mlxsw hwmon interface) to report current
temp to thermal core. The ASIC's PWM is then used to control speed
of system fans registered as cooling devices.
Signed-off-by: NIvan Vecera <cera@cera.cz>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Start adding support for mv88e6390

This is the first patchset implementing support for the mv88e6390
family.  This is a new generation of switch devices and has numerous
incompatible changes to the registers. These patches allow the switch
to the detected during probe, and makes the statistics unit work.

These patches are insufficient to make the mv88e6390 functional. More
patches will follow.

v2:
  Move stats code into global1
  Change DT compatible string to mv88e6190
  Fixed mv88e6351 stats which v1 had broken
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v2:
  Rename functions to avoid _ prefix.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
v2:
  Rename to mv88e6390_g1_stats_set_histogram
  Move into global1.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

_mv88e6xxx_stats_wait() did not check the return value from
 mv88e6xxx_g1_read(), so the compiler complained about set but unused
 err.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull apparmor bugfix from James Morris:
 "This has a fix for a policy replacement bug that is fairly serious for
  apache mod_apparmor users, as it results in the wrong policy being
  applied on an network facing service"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  apparmor: fix change_hat not finding hat after policy replacement

Pull sparc fixes from David Miller:

 1) With modern networking cards we can run out of 32-bit DMA space, so
    support 64-bit DMA addressing when possible on sparc64. From Dave
    Tushar.

 2) Some signal frame validation checks are inverted on sparc32, fix
    from Andreas Larsson.

 3) Lockdep tables can get too large in some circumstances on sparc64,
    add a way to adjust the size a bit. From Babu Moger.

 4) Fix NUMA node probing on some sun4v systems, from Thomas Tai.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: drop duplicate header scatterlist.h
  lockdep: Limit static allocations if PROVE_LOCKING_SMALL is defined
  config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc
  sunbmac: Fix compiler warning
  sunqe: Fix compiler warnings
  sparc64: Enable 64-bit DMA
  sparc64: Enable sun4v dma ops to use IOMMU v2 APIs
  sparc64: Bind PCIe devices to use IOMMU v2 service
  sparc64: Initialize iommu_map_table and iommu_pool
  sparc64: Add ATU (new IOMMU) support
  sparc64: Add FORCE_MAX_ZONEORDER and default to 13
  sparc64: fix compile warning section mismatch in find_node()
  sparc32: Fix inverted invalid_frame_pointer checks on sigreturns
  sparc64: Fix find_node warning if numa node cannot be found

Pull networking fixes from David Miller:

 1) Clear congestion control state when changing algorithms on an
    existing socket, from Florian Westphal.

 2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
    from Jia Jie Ho.

 3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
    CAVALLARO.

 4) Fix udplite multicast delivery handling, it ignores the udp_table
    parameter passed into the lookups, from Pablo Neira Ayuso.

 5) Synchronize the space estimated by rtnl_vfinfo_size and the space
    actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.

 6) Fix memory leak in fib_info when splitting nodes, from Alexander
    Duyck.

 7) If a driver does a napi_hash_del() explicitily and not via
    netif_napi_del(), it must perform RCU synchronization as needed. Fix
    this in virtio-net and bnxt drivers, from Eric Dumazet.

 8) Likewise, it is not necessary to invoke napi_hash_del() is we are
    also doing neif_napi_del() in the same code path. Remove such calls
    from be2net and cxgb4 drivers, also from Eric Dumazet.

 9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
    from WANG Cong.

10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.

11) We cannot cache routes in ip6_tunnel when using inherited traffic
    classes, from Paolo Abeni.

12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.

13) Splice operations cannot use freezable blocking calls in AF_UNIX,
    from WANG Cong.

14) Link dump filtering by master device and kind support added an error
    in loop index updates during the dump if we actually do filter, fix
    from Zhang Shengju.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
  tcp: zero ca_priv area when switching cc algorithms
  net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
  ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
  tipc: eliminate obsolete socket locking policy description
  rtnl: fix the loop index update error in rtnl_dump_ifinfo()
  l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
  net: macb: add check for dma mapping error in start_xmit()
  rtnetlink: fix FDB size computation
  netns: fix get_net_ns_by_fd(int pid) typo
  af_unix: conditionally use freezable blocking calls in read
  net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
  net: ethernet: ti: cpsw: add missing sanity check
  net: ethernet: ti: cpsw: fix secondary-emac probe error path
  net: ethernet: ti: cpsw: fix of_node and phydev leaks
  net: ethernet: ti: cpsw: fix deferred probe
  net: ethernet: ti: cpsw: fix mdio device reference leak
  net: ethernet: ti: cpsw: fix bad register access in probe error path
  net: sky2: Fix shutdown crash
  cfg80211: limit scan results cache size
  net sched filters: pass netlink message flags in event notification
  ...

Declare the structure ieee802154_ops as const as it is only passed as an
argument to the function  ieee802154_alloc_hw. This argument is of type
const struct ieee802154_ops *, so ieee80254_ops structures having this
property can be declared as const.
Done using Coccinelle:

@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ieee802154_ops i@p = {...};

@ok1@
identifier r1.i;
position p;
expression e1;
@@
ieee802154_alloc_hw(e1,&i@p)

@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ieee802154_ops  i={...};

@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ieee802154_ops  i;

The before and after size details of the affected files are:

   text	   data	    bss	    dec	    hex	filename
   8669	   1176	     16	   9861	   2685	drivers/net/ieee802154/adf7242.o
   8805	   1048	     16	   9869	   268d	drivers/net/ieee802154/adf7242.o

   text	   data	    bss	    dec	    hex	filename
   7211	   2296	     32	   9539	   2543	drivers/net/ieee802154/atusb.o
   7339	   2160	     32	   9531	   253b	drivers/net/ieee802154/atusb.o
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Acked-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pravin B Shelar says:

====================
geneve: Use LWT more effectively.

Following patch series make use of geneve LWT code path for
geneve netdev type of device.
This allows us to simplify geneve module without changing any
functionality.

v2-v3:
Rebase against latest net-next.

v1-v2:
Fix warning reported by kbuild test robot.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than comparing 64-bit tunnel-id, compare tunnel vni
which is 24-bit id. This also save conversion from vni
to tunnel id on each tunnel packet receive.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Geneve already has check for device socket in route
lookup function. So no need to check it in xmit
function.
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>