This is me being a bit OCD after all the dentry optimization work this
merge window: profiles end up showing 'dput()' as a rather expensive
operation, and there were two unrelated bad reasons for that.

The first reason was reading d_lockref.count for debugging purposes,
which touches the lockref cacheline (for reads) before really need to.
More importantly, the debugging test in question is _wrong_, and has
hidden bugs.  It's true that we can only sleep when the count goes down
to zero, but the test as-is hides the much more subtle bug that happens
if we race with somebody else deleting the file.

Anyway we _will_ touch that cacheline, but let's do it for a write and
in the right routine (ie in "lockref_put_or_lock()") which annotates the
costs better.  So remove the misleading debug code.

The other was an unnecessary access to the cacheline that contains the
d_lru list, just to check whether we already were on the LRU list or
not.  This is exactly what we have d_flags for, so that we can avoid
touching extra cache lines for the common case.  So just add another bit
for "is this dentry on the LRU".

Finally, mark the tests properly likely/unlikely, so that the common
fast-paths are dense in the instruction stream.

This makes the profiles look much saner.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The only actual current lockref user (dcache) uses zero reference counts
even for perfectly live dentries, because it's a cache: there may not be
any users, but that doesn't mean that we want to throw away the dentry.

At the same time, the dentry cache does have a notion of a truly "dead"
dentry that we must not even increment the reference count of, because
we have pruned it and it is not valid.

Currently that distinction is not visible in the lockref itself, and the
dentry cache validation uses "lockref_get_or_lock()" to either get a new
reference to a dentry that already had existing references (and thus
cannot be dead), or get the dentry lock so that we can then verify the
dentry and increment the reference count under the lock if that
verification was successful.

That's all somewhat complicated.

This adds the concept of being "dead" to the lockref itself, by simply
using a count that is negative.  This allows a usage scenario where we
can increment the refcount of a dentry without having to validate it,
and pushing the special "we killed it" case into the lockref code.

The dentry code itself doesn't actually use this yet, and it's probably
too late in the merge window to do that code (the dentry_kill() code
with its "should I decrement the count" logic really is pretty complex
code), but let's introduce the concept at the lockref level now.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commits 61e00655, 73f8645d and 8e22ecb6:
  "Input: introduce BTN/ABS bits for drums and guitars"
  "HID: wiimote: add support for Guitar-Hero drums"
  "HID: wiimote: add support for Guitar-Hero guitars"

The extra new ABS_xx values resulted in ABS_MAX no longer being a
power-of-two, which broke the comparison logic.  It also caused the
ioctl numbers to overflow into the next byte, causing problems for that.

We'll try again for 3.13.
Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Acked-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch reinstates commits
	67822649
	39761214
	0b95a7f8
	31d93962
	2d31e518

Now that module softdeps are in the kernel we can use that to resolve
the boot issue which cause the revert.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Commit 4edaa308 "NFS: Use "krb5i" to establish NFSv4 state whenever possible"
uses the nfs_client cl_rpcclient for all state management operations, and
will use krb5i or auth_sys with no regard to the mount command authflavor
choice.

The MDS, as any NFSv4.1 mount point, uses the nfs_server rpc client for all
non-state management operations with a different nfs_server for each fsid
encountered traversing the mount point, each with a potentially different
auth flavor.

pNFS data servers are not mounted in the normal sense as there is no associated
nfs_server structure. Data servers can also export multiple fsids, each with
a potentially different auth flavor.

Data servers need to use the same authflavor as the MDS server rpc client for
non-state management operations. Populate a list of rpc clients with the MDS
server rpc client auth flavor for the DS to use.
Signed-off-by: NAndy Adamson <andros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Provide a kernel-doc comment documentation for the BQL helpers:
- netdev_sent_queue
- netdev_completed_queue
- netdev_reset_queue

Similarly to how it is done for the other functions, the documentation
only covers the function operating on struct net_device and not struct
netdev_queue.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the fscache code expect the netfs to call fscache_readpages_or_alloc
inside the aops readpages callback.  It marks all the pages in the list
provided by readahead with PG_private_2.  In the cases that the netfs fails to
read all the pages (which is legal) it ends up returning to the readahead and
triggering a BUG.  This happens because the page list still contains marked
pages.

This patch implements a simple fscache_readpages_cancel function that the netfs
should call before returning from readpages.  It will revoke the pages from the
underlying cache backend and unmark them.

The problem was originally worked out in the Ceph devel tree, but it also
occurs in CIFS.  It appears that NFS, AFS and 9P are okay as read_cache_pages()
will clean up the unprocessed pages in the case of an error.

This can be used to address the following oops:

[12410647.597278] BUG: Bad page state in process petabucket  pfn:3d504e
[12410647.597292] page:ffffea000f541380 count:0 mapcount:0 mapping:
	(null) index:0x0
[12410647.597298] page flags: 0x200000000001000(private_2)

...

[12410647.597334] Call Trace:
[12410647.597345]  [<ffffffff815523f2>] dump_stack+0x19/0x1b
[12410647.597356]  [<ffffffff8111def7>] bad_page+0xc7/0x120
[12410647.597359]  [<ffffffff8111e49e>] free_pages_prepare+0x10e/0x120
[12410647.597361]  [<ffffffff8111fc80>] free_hot_cold_page+0x40/0x170
[12410647.597363]  [<ffffffff81123507>] __put_single_page+0x27/0x30
[12410647.597365]  [<ffffffff81123df5>] put_page+0x25/0x40
[12410647.597376]  [<ffffffffa02bdcf9>] ceph_readpages+0x2e9/0x6e0 [ceph]
[12410647.597379]  [<ffffffff81122a8f>] __do_page_cache_readahead+0x1af/0x260
[12410647.597382]  [<ffffffff81122ea1>] ra_submit+0x21/0x30
[12410647.597384]  [<ffffffff81118f64>] filemap_fault+0x254/0x490
[12410647.597387]  [<ffffffff8113a74f>] __do_fault+0x6f/0x4e0
[12410647.597391]  [<ffffffff810125bd>] ? __switch_to+0x16d/0x4a0
[12410647.597395]  [<ffffffff810865ba>] ? finish_task_switch+0x5a/0xc0
[12410647.597398]  [<ffffffff8113d856>] handle_pte_fault+0xf6/0x930
[12410647.597401]  [<ffffffff81008c33>] ? pte_mfn_to_pfn+0x93/0x110
[12410647.597403]  [<ffffffff81008cce>] ? xen_pmd_val+0xe/0x10
[12410647.597405]  [<ffffffff81005469>] ? __raw_callee_save_xen_pmd_val+0x11/0x1e
[12410647.597407]  [<ffffffff8113f361>] handle_mm_fault+0x251/0x370
[12410647.597411]  [<ffffffff812b0ac4>] ? call_rwsem_down_read_failed+0x14/0x30
[12410647.597414]  [<ffffffff8155bffa>] __do_page_fault+0x1aa/0x550
[12410647.597418]  [<ffffffff8108011d>] ? up_write+0x1d/0x20
[12410647.597422]  [<ffffffff8113141c>] ? vm_mmap_pgoff+0xbc/0xe0
[12410647.597425]  [<ffffffff81143bb8>] ? SyS_mmap_pgoff+0xd8/0x240
[12410647.597427]  [<ffffffff8155c3ae>] do_page_fault+0xe/0x10
[12410647.597431]  [<ffffffff81558818>] page_fault+0x28/0x30
Signed-off-by: NMilosz Tanski <milosz@adfin.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Extend the fscache netfs API so that the netfs can ask as to whether a cache
object is up to date with respect to its corresponding netfs object:

	int fscache_check_consistency(struct fscache_cookie *cookie)

This will call back to the netfs to check whether the auxiliary data associated
with a cookie is correct.  It returns 0 if it is and -ESTALE if it isn't; it
may also return -ENOMEM and -ERESTARTSYS.

The backends now have to implement a mandatory operation pointer:

	int (*check_consistency)(struct fscache_object *object)

that corresponds to the above API call.  FS-Cache takes care of pinning the
object and the cookie in memory and managing this call with respect to the
object state.

Original-author: Hongyi Jia <jiayisuse@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
cc: Hongyi Jia <jiayisuse@gmail.com>
cc: Milosz Tanski <milosz@adfin.com>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

We check submounts before doing d_drop() on a non-empty directory dentry in
NFS (have_submounts()), but we do not exclude a racing mount.

 Process A: have_submounts() -> returns false
 Process B: mount() -> success
 Process A: d_drop()

This patch prepares the ground for the fix by doing the following
operations all under the same rename lock:

  have_submounts()
  shrink_dcache_parent()
  d_drop()

This is actually an optimization since have_submounts() and
shrink_dcache_parent() both traverse the same dentry tree separately.
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
CC: David Howells <dhowells@redhat.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
CC: Trond Myklebust <Trond.Myklebust@netapp.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

This patch adds two more ndo ops: ndo_add_rx_vxlan_port() and
ndo_del_rx_vxlan_port().

Drivers can get notifications through the above functions about changes
of the UDP listening port of VXLAN. Also, when physical ports come up,
now they can call vxlan_get_rx_port() in order to obtain the port number(s)
of the existing VXLAN interface in case they already up before them.

This information about the listening UDP port would be used for VXLAN
related offloads.

A big thank you to John Fastabend (john.r.fastabend@intel.com) for his
input and his suggestions on this patch set.

CC: John Fastabend <john.r.fastabend@intel.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJoseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WRITE and COMMIT can use the machine credential.

If WRITE is supported and COMMIT is not, make all (mach cred) writes FILE_SYNC4.
Signed-off-by: NWeston Andros Adamson <dros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

TEST_STATEID and FREE_STATEID can use the machine credential.
Signed-off-by: NWeston Andros Adamson <dros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

SECINFO and SECINFO_NONAME can use the machine credential.
Signed-off-by: NWeston Andros Adamson <dros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

CLOSE and LOCKU can use the machine credential.
Signed-off-by: NWeston Andros Adamson <dros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

This is a minimal client side implementation of SP4_MACH_CRED.  It will
attempt to negotiate SP4_MACH_CRED iff the EXCHANGE_ID is using
krb5i or krb5p auth.  SP4_MACH_CRED will be used if the server supports the
minimal operations:

 BIND_CONN_TO_SESSION
 EXCHANGE_ID
 CREATE_SESSION
 DESTROY_SESSION
 DESTROY_CLIENTID

This patch only includes the EXCHANGE_ID negotiation code because
the client will already use the machine cred for these operations.

If the server doesn't support SP4_MACH_CRED or doesn't support the minimal
operations, the exchange id will be resent with SP4_NONE.
Signed-off-by: NWeston Andros Adamson <dros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Instead of the pointer values, use the task and client identifier values
for tracing purposes.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Add an identifier in order to aid debugging.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

The patch replaces all occurrences of struct fb_videomode by
more accurate struct videomode. The change allows to remove
mode conversion function and simplifies clock divider calculation.
Clock configuration is moved to separate function.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Get rid of MLDV2_MRC and use our new macros for mantisse and
exponent to calculate Maximum Response Delay out of the Maximum
Response Code.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i) RFC3810, 9.2. Query Interval [QI] says:

   The Query Interval variable denotes the interval between General
   Queries sent by the Querier. Default value: 125 seconds. [...]

ii) RFC3810, 9.3. Query Response Interval [QRI] says:

  The Maximum Response Delay used to calculate the Maximum Response
  Code inserted into the periodic General Queries. Default value:
  10000 (10 seconds) [...] The number of seconds represented by the
  [Query Response Interval] must be less than the [Query Interval].

iii) RFC3810, 9.12. Older Version Querier Present Timeout [OVQPT] says:

  The Older Version Querier Present Timeout is the time-out for
  transitioning a host back to MLDv2 Host Compatibility Mode. When an
  MLDv1 query is received, MLDv2 hosts set their Older Version Querier
  Present Timer to [Older Version Querier Present Timeout].

  This value MUST be ([Robustness Variable] times (the [Query Interval]
  in the last Query received)) plus ([Query Response Interval]).

Hence, on *default* the timeout results in:

  [RV] = 2, [QI] = 125sec, [QRI] = 10sec
  [OVQPT] = [RV] * [QI] + [QRI] = 260sec

Having that said, we currently calculate [OVQPT] (here given as 'switchback'
variable) as ...

  switchback = (idev->mc_qrv + 1) * max_delay

RFC3810, 9.12. says "the [Query Interval] in the last Query received". In
section "9.14. Configuring timers", it is said:

  This section is meant to provide advice to network administrators on
  how to tune these settings to their network. Ambitious router
  implementations might tune these settings dynamically based upon
  changing characteristics of the network. [...]

iv) RFC38010, 9.14.2. Query Interval:

  The overall level of periodic MLD traffic is inversely proportional
  to the Query Interval. A longer Query Interval results in a lower
  overall level of MLD traffic. The value of the Query Interval MUST
  be equal to or greater than the Maximum Response Delay used to
  calculate the Maximum Response Code inserted in General Query
  messages.

I assume that was why switchback is calculated as is (3 * max_delay), although
this setting seems to be meant for routers only to configure their [QI]
interval for non-default intervals. So usage here like this is clearly wrong.

Concluding, the current behaviour in IPv6's multicast code is not conform
to the RFC as switch back is calculated wrongly. That is, it has a too small
value, so MLDv2 hosts switch back again to MLDv2 way too early, i.e. ~30secs
instead of ~260secs on default.

Hence, introduce necessary helper functions and fix this up properly as it
should be.

Introduced in 06da92283 ("[IPV6]: Add MLDv2 support."). Credits to Hannes
Frederic Sowa who also had a hand in this as well. Also thanks to Hangbin Liu
who did initial testing.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: David Stevens <dlstevens@us.ibm.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

The current VFIO_DEVICE_RESET interface only maps to PCI use cases
where we can isolate the reset to the individual PCI function.  This
means the device must support FLR (PCIe or AF), PM reset on D3hot->D0
transition, device specific reset, or be a singleton device on a bus
for a secondary bus reset.  FLR does not have widespread support,
PM reset is not very reliable, and bus topology is dictated by the
system and device design.  We need to provide a means for a user to
induce a bus reset in cases where the existing mechanisms are not
available or not reliable.

This device specific extension to VFIO provides the user with this
ability.  Two new ioctls are introduced:
 - VFIO_DEVICE_PCI_GET_HOT_RESET_INFO
 - VFIO_DEVICE_PCI_HOT_RESET

The first provides the user with information about the extent of
devices affected by a hot reset.  This is essentially a list of
devices and the IOMMU groups they belong to.  The user may then
initiate a hot reset by calling the second ioctl.  We must be
careful that the user has ownership of all the affected devices
found via the first ioctl, so the second ioctl takes a list of file
descriptors for the VFIO groups affected by the reset.  Each group
must have IOMMU protection established for the ioctl to succeed.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>

Solution:
=========

- Synchronize linux's `include/uapi/linux/in6.h'
  with glibc's `inet/netinet/in.h'.
- Synchronize glibc's `inet/netinet/in.h with linux's
  `include/uapi/linux/in6.h'.
- Allow including the headers in either other.
- First header included defines the structures and macros.

Details:
========

The kernel promises not to break the UAPI ABI so I don't
see why we can't just have the two userspace headers
coordinate?

If you include the kernel headers first you get those,
and if you include the glibc headers first you get those,
and the following patch arranges a coordination and
synchronization between the two.

Let's handle `include/uapi/linux/in6.h' from linux,
and `inet/netinet/in.h' from glibc and ensure they compile
in any order and preserve the required ABI.

These two patches pass the following compile tests:

cat >> test1.c <<EOF
int main (void) {
  return 0;
}
EOF
gcc -c test1.c

cat >> test2.c <<EOF
int main (void) {
  return 0;
}
EOF
gcc -c test2.c

One wrinkle is that the kernel has a different name for one of
the members in ipv6_mreq. In the kernel patch we create a macro
to cover the uses of the old name, and while that's not entirely
clean it's one of the best solutions (aside from an anonymous
union which has other issues).

I've reviewed the code and it looks to me like the ABI is
assured and everything matches on both sides.

Notes:
- You want netinet/in.h to include bits/in.h as early as possible,
  but it needs in_addr so define in_addr early.
- You want bits/in.h included as early as possible so you can use
  the linux specific code to define __USE_KERNEL_DEFS based on
  the _UAPI_* macro definition and use those to cull in.h.
- glibc was missing IPPROTO_MH, added here.

Compile tested and inspected.
Reported-by: NThomas Backlund <tmb@mageia.org>
Cc: Thomas Backlund <tmb@mageia.org>
Cc: libc-alpha@sourceware.org
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NCarlos O'Donell <carlos@redhat.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an NFSv4 client loses contact with the server it can lose any
locks that it holds.

Currently when it reconnects to the server it simply tries to reclaim
those locks.  This might succeed even though some other client has
held and released a lock in the mean time.  So the first client might
think the file is unchanged, but it isn't.  This isn't good.

If, when recovery happens, the locks cannot be claimed because some
other client still holds the lock, then we get a message in the kernel
logs, but the client can still write.  So two clients can both think
they have a lock and can both write at the same time.  This is equally
not good.

There was a patch a while ago
  http://comments.gmane.org/gmane.linux.nfs/41917

which tried to address some of this, but it didn't seem to go
anywhere.  That patch would also send a signal to the process.  That
might be useful but for now this patch just causes writes to fail.

For NFSv4 (unlike v2/v3) there is a strong link between the lock and
the write request so we can fairly easily fail any IO of the lock is
gone.  While some applications might not expect this, it is still
safer than allowing the write to succeed.

Because this is a fairly big change in behaviour a module parameter,
"recover_locks", is introduced which defaults to true (the current
behaviour) but can be set to "false" to tell the client not to try to
recover things that were lost.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Add client side debugging to help trace socket connection/disconnection
and unexpected state change issues.
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Add support to the core direct-io code to defer AIO completions to user
context using a workqueue.  This replaces opencoded and less efficient
code in XFS and ext4 (we save a memory allocation for each direct IO)
and will be needed to properly support O_(D)SYNC for AIO.

The communication between the filesystem and the direct I/O code requires
a new buffer head flag, which is a bit ugly but not avoidable until the
direct I/O code stops abusing the buffer_head structure for communicating
with the filesystems.

Currently this creates a per-superblock unbound workqueue for these
completions, which is taken from an earlier patch by Jan Kara.  I'm
not really convinced about this use and would prefer a "normal" global
workqueue with a high concurrency limit, but this needs further discussion.

JK: Fixed ext4 part, dynamic allocation of the workqueue.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

HID_REPORT_TYPES defines the number of available report-types. Move it
closer to the actualy definition of the report-types so we can see the
relation more clearly (and hopefully will never forget to update it).
Signed-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

There are a bunch of guitar and drums devices out there that all report
similar data. To avoid reporting this as BTN_MISC or ABS_MISC, we
allocate some proper namespace for them. Note that most of these devices
are toys and we cannot report any sophisticated physics via this API.

I did some google-images research and tried to provide definitions that
work with all common devices. That's why I went with 4 toms, 4 cymbals,
one bass, one hi-hat. I haven't seen other drums and I doubt that we need
any additions to that. Anyway, the naming-scheme is intentionally done in
an extensible way.

For guitars, we support 5 frets (normally aligned vertically, compared to
the real horizontal layouts), a single strum-bar with up/down directions,
an optional fret-board and a whammy-bar.

Most of the devices provide pressure values so I went with ABS_* bits. If
we ever support devices which only provide digital input, we have to
decide whether to emulate pressure data or add additional BTN_* bits.

If someone is not familiar with these devices, here are two pictures which
provide almost all introduced interfaces (or try the given keywords
with a google-image search):
  Guitar: ("guitar hero world tour guitar")
    http://images1.wikia.nocookie.net/__cb20120911023442/applezone/es/images/f/f9/Wii_Guitar.jpg
  Drums: ("guitar hero drums")
    http://oyster.ignimgs.com/franchises/images/03/55/35526_band-hero-drum-set-hands-on-20090929040735768.jpgSigned-off-by: NDavid Herrmann <dh.herrmann@gmail.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

tcp_rcv_established() returns only one value namely 0. We change the return
value to void (as suggested by David Miller).

After commit 0c24604b (tcp: implement RFC 5961 4.2), we no longer send RSTs in
response to SYNs. We can remove the check and processing on the return value of
tcp_rcv_established().

We also fix jtcp_rcv_established() in tcp_probe.c to match that of
tcp_rcv_established().
Signed-off-by: NVijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The goal of this patch is to harmonize cleanup done on a skbuff on rx path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The goal of this patch is to harmonize cleanup done on a skbuff on xmit path.
Before this patch, behaviors were different depending of the tunnel type.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function was only used when a packet was sent to another netns. Now, it can
also be used after tunnel encapsulation or decapsulation.

Only skb_orphan() should not be done when a packet is not crossing netns.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This argument is not used, let's remove it.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This argument is not used, let's remove it.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

same story as with oprofilefs_mkdir()
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

it's always equal to ->d_sb of the second argument (parent dentry),
due to either being literally that, or ->d_sb of parent's parent.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>