o Do not obtain link speed from register when adapter
  link is down.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was not handling external loopback diagnostic
test request.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Delete MAC address from the adapter's filter table
  if the source MAC address of ingress packet matches.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver was passing the address of a pointer instead of
the pointer itself.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NetLabel has the ability to selectively assign network security labels
to outbound traffic based on either the LSM's "domain" (different for
each LSM), the network destination, or a combination of both.  Depending
on the type of traffic, local or forwarded, and the type of traffic
selector, domain or address based, different hooks are used to label the
traffic; the goal being minimal overhead.

Unfortunately, there is a bug such that a system using NetLabel domain
based traffic selectors does not correctly label outbound local traffic
that is not assigned to a socket.  The issue is that in these cases
the associated NetLabel hook only looks at the address based selectors
and not the domain based selectors.  This patch corrects this by
checking both the domain and address based selectors so that the correct
labeling is applied, regardless of the configuration type.

In order to acomplish this fix, this patch also simplifies some of the
NetLabel domainhash structures to use a more common outbound traffic
mapping type: struct netlbl_dommap_def.  This simplifies some of the code
in this patch and paves the way for further simplifications in the
future.
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's possible to assign an invalid value to the net.core.somaxconn
sysctl variable, because there is no checks at all.

The sk_max_ack_backlog field of the sock structure is defined as
unsigned short. Therefore, the backlog argument in inet_listen()
shouldn't exceed USHRT_MAX. The backlog argument in the listen() syscall
is truncated to the somaxconn value. So, the somaxconn value shouldn't
exceed 65535 (USHRT_MAX).
Also, negative values of somaxconn are meaningless.

before:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
net.core.somaxconn = 65536
$ sysctl -w net.core.somaxconn=-100
net.core.somaxconn = -100

after:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
error: "Invalid argument" setting key "net.core.somaxconn"
$ sysctl -w net.core.somaxconn=-100
error: "Invalid argument" setting key "net.core.somaxconn"

Based on a prior patch from Changli Gao.
Signed-off-by: NRoman Gushchin <klamm@yandex-team.ru>
Reported-by: NChangli Gao <xiaosuo@gmail.com>
Suggested-by: NEric Dumazet <edumazet@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[  198.720048] ------------[ cut here ]------------
[  198.720108] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:255 dev_watchdog+0x229/0x240()
[  198.720118] NETDEV WATCHDOG: eth0 (sis900): transmit queue 0 timed out
[  198.720125] Modules linked in: bridge stp llc dmfe sundance 3c59x sis900 mii
[  198.720159] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc3+ #12
[  198.720167] Hardware name: System Manufacturer System Name/TUSI-M, BIOS ASUS TUSI-M ACPI BIOS
Revision 1013 Beta 001 12/14/2001
[  198.720175]  000000ff c13fa6b9 c169ddcc c12208d6 c169ddf8 c1031e4d c1664a84 c169de24
[  198.720197]  00000000 c165f5ea 000000ff c13fa6b9 00000001 000000ff c1664a84 c169de10
[  198.720217]  c1031f13 00000009 c169de08 c1664a84 c169de24 c169de50 c13fa6b9 c165f5ea
[  198.720240] Call Trace:
[  198.720257]  [<c13fa6b9>] ? dev_watchdog+0x229/0x240
[  198.720274]  [<c12208d6>] dump_stack+0x16/0x20
[  198.720306]  [<c1031e4d>] warn_slowpath_common+0x7d/0xa0
[  198.720318]  [<c13fa6b9>] ? dev_watchdog+0x229/0x240
[  198.720330]  [<c1031f13>] warn_slowpath_fmt+0x33/0x40
[  198.720342]  [<c13fa6b9>] dev_watchdog+0x229/0x240
[  198.720357]  [<c103f158>] call_timer_fn+0x78/0x150
[  198.720369]  [<c103f0e0>] ? internal_add_timer+0x40/0x40
[  198.720381]  [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0
[  198.720392]  [<c103f33f>] run_timer_softirq+0x10f/0x200
[  198.720412]  [<c103954f>] ? __do_softirq+0x6f/0x210
[  198.720424]  [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0
[  198.720435]  [<c1039598>] __do_softirq+0xb8/0x210
[  198.720467]  [<c14b54d2>] ? _raw_spin_unlock+0x22/0x30
[  198.720484]  [<c1003245>] ? handle_irq+0x25/0xd0
[  198.720496]  [<c1039c0c>] irq_exit+0x9c/0xb0
[  198.720508]  [<c14bc9d7>] do_IRQ+0x47/0x94
[  198.720534]  [<c1056078>] ? hrtimer_start+0x28/0x30
[  198.720564]  [<c14bc8b1>] common_interrupt+0x31/0x38
[  198.720589]  [<c1008692>] ? default_idle+0x22/0xa0
[  198.720600]  [<c10083c7>] arch_cpu_idle+0x17/0x30
[  198.720631]  [<c106d23d>] cpu_startup_entry+0xcd/0x180
[  198.720643]  [<c14ae30a>] rest_init+0xaa/0xb0
[  198.720654]  [<c14ae260>] ? reciprocal_value+0x50/0x50
[  198.720668]  [<c17044e0>] ? repair_env_string+0x60/0x60
[  198.720679]  [<c1704bda>] start_kernel+0x29a/0x350
[  198.720690]  [<c17044e0>] ? repair_env_string+0x60/0x60
[  198.720721]  [<c1704269>] i386_start_kernel+0x39/0xa0
[  198.720729] ---[ end trace 81e0a6266f5c73a8 ]---
[  198.720740] eth0: Transmit timeout, status 00000204 00000000

timer routine checks the link status and if it's up calls
netif_carrier_on() allowing upper layer to start the tx queue
even if the auto-negotiation process is not finished.

Also remove ugly auto-negotiation check from the sis900_start_xmit()

CC: Duan Fugang <B38611@freescale.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 5c766d64 ("ipv4: introduce address lifetime") leaves the ifa
resource that was allocated via inet_alloc_ifa() unfreed when returning
the function with -EINVAL. Thus, free it first via inet_free_ifa().
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This message was added in commit a7154cb8 (June 2004, [PATCH] r8169:
link handling and phy reset rework) and is printed every ten seconds
when no cable is connected and runtime power management is disabled.
(Before that commit, "Reset RTL8169s PHY" would be printed instead.)
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRQF_DISABLED is a no-op by now and should be
removed.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When userspace passes a large priority value
the assignment of the unsigned value hopt->prio
to  signed int cl->prio causes cl->prio to become negative and the
comparison is with TC_HTB_NUMPRIO is always false.

The result is that HTB crashes by referencing outside
the array when processing packets. With this patch the large value
wraps around like other values outside the normal range.

See: https://bugzilla.kernel.org/show_bug.cgi?id=60669Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's quite unlikely that dev_set_promiscuity will fail,
but worth checking just in case.

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

macvlan passthrough mode is special: it's not possible to switch to or
from it through a netlink command.

But if you try, the command will succeed, which is
confusing.

Validate input and return error to user.

Cc:  Sridhar Samudrala <sri@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When creation of TIPC internal server socket fails,
we get an oops with the following dump:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: [<ffffffffa0011f49>] tipc_close_conn+0x59/0xb0 [tipc]
PGD 13719067 PUD 12008067 PMD 0
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: tipc(+)
CPU: 4 PID: 4340 Comm: insmod Not tainted 3.10.0+ #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
task: ffff880014360000 ti: ffff88001374c000 task.ti: ffff88001374c000
RIP: 0010:[<ffffffffa0011f49>]  [<ffffffffa0011f49>] tipc_close_conn+0x59/0xb0 [tipc]
RSP: 0018:ffff88001374dc98  EFLAGS: 00010292
RAX: 0000000000000000 RBX: ffff880012ac09d8 RCX: 0000000000000000
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffff880014360000
RBP: ffff88001374dcb8 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffa0016fa0
R13: ffffffffa0017010 R14: ffffffffa0017010 R15: ffff880012ac09d8
FS:  0000000000000000(0000) GS:ffff880016600000(0063) knlGS:00000000f76668d0
CS:  0010 DS: 002b ES: 002b CR0: 000000008005003b
CR2: 0000000000000020 CR3: 0000000012227000 CR4: 00000000000006e0
Stack:
ffff88001374dcb8 ffffffffa0016fa0 0000000000000000 0000000000000001
ffff88001374dcf8 ffffffffa0012922 ffff88001374dce8 00000000ffffffea
ffffffffa0017100 0000000000000000 ffff8800134241a8 ffffffffa0017150
Call Trace:
[<ffffffffa0012922>] tipc_server_stop+0xa2/0x1b0 [tipc]
[<ffffffffa0009995>] tipc_subscr_stop+0x15/0x20 [tipc]
[<ffffffffa00130f5>] tipc_core_stop+0x1d/0x33 [tipc]
[<ffffffffa001f0d4>] tipc_init+0xd4/0xf8 [tipc]
[<ffffffffa001f000>] ? 0xffffffffa001efff
[<ffffffff8100023f>] do_one_initcall+0x3f/0x150
[<ffffffff81082f4d>] ? __blocking_notifier_call_chain+0x7d/0xd0
[<ffffffff810cc58a>] load_module+0x11aa/0x19c0
[<ffffffff810c8d60>] ? show_initstate+0x50/0x50
[<ffffffff8190311c>] ? retint_restore_args+0xe/0xe
[<ffffffff810cce79>] SyS_init_module+0xd9/0x110
[<ffffffff8190dc65>] sysenter_dispatch+0x7/0x1f
Code: 6c 24 70 4c 89 ef e8 b7 04 8f e1 8b 73 04 4c 89 e7 e8 7c 9e 32 e1 41 83 ac 24
b8 00 00 00 01 4c 89 ef e8 eb 0a 8f e1 48 8b 43 08 <4c> 8b 68 20 4d 8d a5 48 03 00
00 4c 89 e7 e8 04 05 8f e1 4c 89
RIP  [<ffffffffa0011f49>] tipc_close_conn+0x59/0xb0 [tipc]
RSP <ffff88001374dc98>
CR2: 0000000000000020
---[ end trace b02321f40e4269a3 ]---

We have the following call chain:

tipc_core_start()
    ret = tipc_subscr_start()
        ret = tipc_server_start(){
                  server->enabled = 1;
                  ret = tipc_open_listening_sock()
              }

I.e., the server->enabled flag is unconditionally set to 1, whatever
the return value of tipc_open_listening_sock().

This causes a crash when tipc_core_start() tries to clean up
resources after a failed initialization:

    if (ret == failed)
        tipc_subscr_stop()
            tipc_server_stop(){
                if (server->enabled)
                    tipc_close_conn(){
                        NULL reference of con->sock-sk
                        OOPS!
                }
            }

To avoid this, tipc_server_start() should only set server->enabled
to 1 in case of a succesful socket creation. In case of failure, it
should release all allocated resources before returning.

Problem introduced in commit c5fa7b3c
("tipc: introduce new TIPC server infrastructure") in v3.11-rc1.
Note that it won't be seen often; it takes a module load under memory
constrained conditions in order to trigger the failure condition.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.

Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_NET_LL_RX_POLL is not set, I got:

net/socket.c: In function ‘sock_poll’:
net/socket.c:1165:4: error: implicit declaration of function ‘sk_busy_loop’ [-Werror=implicit-function-declaration]

Fix this by adding a nop when !CONFIG_NET_LL_RX_POLL.

Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slaves get the 64B CQE/EQE state from QUERY_HCA, not from the module parameter.

If the parameter is set to zero, the slave outputs an incorrect/irrelevant
warning message that 64B CQEs/EQEs are supported but not enabled (even if the
hypervisor has enabled 64B CQEs/EQEs).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the user has not assigned a MAC address to a VM, then don't give it MAC which
is based on the PF one. The current derivation scheme is wrong and leads to VM
MAC collisions when the number of cards/hypervisors becomes big enough.

Instead, just give it zeros and let them figure out what to do with that.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a race in IPv6 automatic addess assignment. The address is created
with zero lifetime when it's added to various address lists. Before it gets
assigned the correct lifetime, there's a window where a new address may be
configured. This causes the semi-initiated address to be deleted in
addrconf_verify.

This was discovered as a reference leak caused by concurrent run of
__ipv6_ifa_notify for both RTM_NEWADDR and RTM_DELADDR with the same
address.

Fix this by setting the lifetime before the address is added to
inet6_addr_lst.

A few notes:

1. In addrconf_prefix_rcv, by setting update_lft to zero, the
   if (update_lft) { ... } condition is no longer executed for newly
   created addresses. This is okay, as the ifp fields are set in
   ipv6_add_addr now and ipv6_ifa_notify is called (and has been called)
   through addrconf_dad_start.

2. The removal of the whole block under ifp->lock in inet6_addr_add is okay,
   too, as tstamp is initialized to jiffies in ipv6_add_addr.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As pointed out by Eric Dumazet, net->ipv6.ip6_rt_last_gc should
hold the last time garbage collector was run so that we should
update it whenever fib6_run_gc() calls fib6_clean_all(), not only
if we got there from ip6_dst_gc().
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a high-traffic router with many processors and many IPv6 dst
entries, soft lockup in fib6_run_gc() can occur when number of
entries reaches gc_thresh.

This happens because fib6_run_gc() uses fib6_gc_lock to allow
only one thread to run the garbage collector but ip6_dst_gc()
doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc()
returns. On a system with many entries, this can take some time
so that in the meantime, other threads pass the tests in
ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for
the lock. They then have to run the garbage collector one after
another which blocks them for quite long.

Resolve this by replacing special value ~0UL of expire parameter
to fib6_run_gc() by explicit "force" parameter to choose between
spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with
force=false if gc_thresh is reached but not max_size.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John W. Linville says:

====================
This pull request is intended for the 3.11 stream.  It is a bit
larger than usual, as it includes pulls from most of my feeder trees
as well...

For the Bluetooth bits, Gustavo says:

"A few fixes and devices ID additions for 3.11:

 * There are 4 new ath3k device ids
 * Fixed stack memory usage in ath3k.
 * Fixed the init process of BlueFRITZ! devices, they were failing to init
   due to an unsupported command we sent.
 * Fixed wrong use of PTR_ERR in btusb code that was preventing intel devices
   to work properly.
 * Fixed race condition between hci_register_dev() and hci_dev_open() that
   could cause a NULL pointer dereference.
 * Fixed race condition that could call hci_req_cmd_complete() and make some
   devices to fail as showed in the log added to the commit message."

Regarding the NFC bits, Samuel says:

"We have:

1) A build failure fix for the NCI SPI transport layer due to a
   missing CRC_CCITT Kconfig dependency.

2) A netlink command rename: CMD_FW_UPLOAD was merged during the 3.11
   merge window but the typical terminology for loading a firmware to a
   target is firmware download rather than upload. In order to avoid any
   confusion in a file exported to userspace, we rename this command to
   CMD_FW_DOWNLOAD."

Samuel's item #2 isn't strictly a fix, but it seems safe and should
avoid confusion in the future.

As for the mac80211 bits, Johannes says:

"I only have three fixes this time, a fix for a suspend regression, a
patch correcting the initiator in regulatory code and one fix for mesh
station powersave."

With respect to the iwlwifi bits, Johannes says:

"We have a scan fix for passive channels, a new PCI device ID for an old
device, a NIC reset fix, an RF-Kill fix, a fix for powersave when GO
interfaces are present as well as an aggregation session fix (for a
corner case) and a workaround for a firmware design issue - it only
supports a single GTK in D3."

Bringing-up the rear with the Atheros trees, Kalle says:

"Geert Uytterhoeven fixed an ath10k build problem when NO_DMA=y. I added
a missing MAINTAINERS entry for ath10k and updated ath6kl git tree
location."

Along with the above...

Arend van Spriel fixes a brcmfmac WARNING when unplugging the device.

Avinash Patil proves a couple of minor mwifiex fixes relating to P2P mode.

Luciano Coelho updates the MAINTAINERS entry for the wilink drivers.

Stanislaw Gruszka brings an rt2x00 fix for a queue start/stop problem.

Stone Piao fixes another mwifiex problem, a command timeout related to P2P mode.

Tomasz Moń corrects an endian problem in mwifiex.

I'll remind my feeder maintainers to slowdown the patchflow.
Beyond that, please let me know if there are problems!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

If there is no querier on a link then we won't get periodic reports and
therefore won't be able to learn about multicast listeners behind ports,
potentially leading to lost multicast packets, especially for multicast
listeners that joined before the creation of the bridge.

These lost multicast packets can appear since c5c23260
("bridge: Add multicast_querier toggle and disable queries by default")
in particular.

With this patch we are flooding multicast packets if our querier is
disabled and if we didn't detect any other querier.

A grace period of the Maximum Response Delay of the querier is added to
give multicast responses enough time to arrive and to be learned from
before disabling the flooding behaviour again.
Signed-off-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Self explanitory dma_mapping_error addition to the 8139 driver, based on this:
https://bugzilla.redhat.com/show_bug.cgi?id=947250

It showed several backtraces arising for dma_map_* usage without checking the
return code on the mapping.  Add the check and abort the rx/tx operation if its
failed.  Untested as I have no hardware and the reporter has wandered off, but
seems pretty straightforward.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "pvc" struct has a hole after pvc.sap_family which is not cleared.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- fix the conversion between cpu and __le32
 - replace some pla_ocp and usb_ocp functions with generic_ocp function
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate the required memory before calling usb_control_msg. And
the additional memory copy is necessary.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace 0 with the result from usbnet_cdc_bind().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't replace the usb_control_msg() with usbnet_{read,write}_cmd()
which couldn't be called inside suspend/resume callback. Keep the
basic functions unlimited. Instead, using usb_autopm_get_interface()
and usb_autopm_put_interface() in r815x_mdio_{read,write}().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some USB buffers use stack which may not be DMA-able.
Use the buffers from kmalloc to replace those one.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix association failures not triggering a connect-failure event in
    cfg80211, from Johannes Berg.

 2) Eliminate a potential NULL deref with older iptables tools when
    configuring xt_socket rules, from Eric Dumazet.

 3) Missing RTNL locking in wireless regulatory code, from Johannes
    Berg.

 4) Fix OOPS caused by firmware loading races in ath9k_htc, from Alexey
    Khoroshilov.

 5) Fix usb URB leak in usb_8dev CAN driver, also from Alexey
    Khoroshilov.

 6) VXLAN namespace teardown fails to unregister devices, from Stephen
    Hemminger.

 7) Fix multicast settings getting dropped by firmware in qlcnic driver,
    from Sucheta Chakraborty.

 8) Add sysctl range enforcement for tcp_syn_retries, from Michal Tesar.

 9) Fix a nasty bug in bridging where an active timer would get
    reinitialized with a setup_timer() call.  From Eric Dumazet.

10) Fix use after free in new mlx5 driver, from Dan Carpenter.

11) Fix freed pointer reference in ipv6 multicast routing on namespace
    cleanup, from Hannes Frederic Sowa.

12) Some usbnet drivers report TSO and SG in their feature set, but the
    usbnet layer doesn't really support them.  From Eric Dumazet.

13) Fix crash on EEH errors in tg3 driver, from Gavin Shan.

14) Drop cb_lock when requesting modules in genetlink, from Stanislaw
    Gruszka.

15) Kernel stack leaks in cbq scheduler and af_key pfkey messages, from
    Dan Carpenter.

16) FEC driver erroneously signals NETDEV_TX_BUSY on transmit leading to
    endless loops, from Uwe Kleine-König.

17) Fix hangs from loading mvneta driver, from Arnaud Patard.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
  mlx5: fix error return code in mlx5_alloc_uuars()
  mvneta: Try to fix mvneta when compiled as module
  mvneta: Fix hang when loading the mvneta driver
  atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
  genetlink: fix usage of NLM_F_EXCL or NLM_F_REPLACE
  af_key: more info leaks in pfkey messages
  net/fec: Don't let ndo_start_xmit return NETDEV_TX_BUSY without link
  net_sched: Fix stack info leak in cbq_dump_wrr().
  igb: fix vlan filtering in promisc mode when not in VT mode
  ixgbe: Fix Tx Hang issue with lldpad on 82598EB
  genetlink: release cb_lock before requesting additional module
  net: fec: workaround stop tx during errata ERR006358
  qlcnic: Fix diagnostic interrupt test for 83xx adapters.
  qlcnic: Fix setting Guest VLAN
  qlcnic: Fix operation type and command type.
  qlcnic: Fix initialization of work function.
  Revert "atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring"
  atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
  net/tg3: Fix warning from pci_disable_device()
  net/tg3: Fix kernel crash
  ...

Samuel Ortiz <sameo@linux.intel.com> says:

'This is the second NFC fixes pull request for 3.11.

We have:

- A build failure fix for the NCI SPI transport layer due to a
  missing CRC_CCITT Kconfig dependency.

- A netlink command rename: CMD_FW_UPLOAD was merged during the 3.11
  merge window but the typical terminology for loading a firmware to a
  target is firmware download rather than upload. In order to avoid any
  confusion in a file exported to userspace, we rename this command into
  CMD_FW_DOWNLOAD."
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	net/bluetooth/hci_core.c

Soon the coelho@ti.com email will not be valid anymore, so change it
to my private one.

Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>