It turns out that there are only 2 in-tree platforms which use MPICs
which are not "primary":  IBM Cell and PowerMac.  To reduce the
complexity of the typical board setup code, invert the MPIC_PRIMARY bit
into MPIC_SECONDARY.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Almost all PowerPC platforms use a standard "open-pic" device node so
the mpic_alloc() function now accepts NULL for the device-node.  This
will cause it to perform a default search with of_find_matching_node().
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The MPIC code can already perform an automatic OF address translation
step as part of mpic_alloc(), but several boards need to use that base
address when they perform mpic_assign_isu().

The easiest solution is to save the computed physical address into the
"struct mpic" for later use by the board code.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Defining flash partition table in platform code is deprecated, and due to
recent changes linkstation and storcenter do not compile any more with
their default configurations because of undefined references to
physmap_set_partitions(). Instead of fixing them by using the correct
kernel configuration macro in preprocessor conditional, remove partition
table definitions altogether. Instead add support for partition definition
on the command-line and in device tree to the default configurations.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The i2c bus defn is broken on linkstation / kurobox machines since at
least 2.6.27. Fix it. Also remove CONFIG_SERIAL_OF_PLATFORM, which, if
enabled, breaks the serial console after the
"console handover: boot [udbg0] -> real [ttyS1]" message.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

On the Freescale embedded (83xx, 85xx, 86xx) and a few of the discrete
bridges (mpc10x, tsi108) use the new for_each_compatible_node() or
for_each_node_by_type() to provide more exact matching when looking for
PHBs in the device tree.

With the previous code it was possible to match on pci bridges since
we were only matching on device_type.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

1. Fix RTC type - it is a rs5c372a, not rs5c372b
2. Configure both UART interrupts edge-triggered
3. Add a license header to ls_uart.c
4. Check for running on linkstation in a late_initcall() function. Needed
   for multiplatform builds, even though linkstation doesn't support them
   yet
5. Remove unneeded #include from linkstation.c
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

To build arch/powerpc without including asm-ppc/ we need these files
in asm-powerpc/

Moved some headers under arch/powerpc/platforms if they were only used by
platform or driver files and fixed up the source file includes to match
the new locations
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This fixes some interrrupt -> interrupt typos.
Signed-off-by: NGabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian.  This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Make the ppc32 pcibios_alloc_controller take a device node to match
the ppc64 prototypes and have it set arch_data.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Some code looks can be configured to be built without
PCI support, but does not work properly.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Many platforms currently define their own add_bridge function, some
of them globally. This breaks some multiplatform configurations.
Prefixing each of these functions with the platform name avoids
this problem.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Linkstation systems capable of running mainline kernels use u-boot as a
bootloader, so, specifying a suitable kernel command is not a problem.
Don't guess. Also extend linkstation_defconfig to support the linkstation HS
model with a IT8212 IDE controller and kuroboxHD/HD-HLAN linkstation
models with a tulip ethernet chip. The latter also require a slightly
different .dts file, which is also included with this patch.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Support for the Kurobox(HG)/LinkStation-I NAS systems by Buffalo
Technology, should be also applicable to the PPC TeraStation family.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>