These aren't useful and overflowing so drop them
and also fix a minor typo.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to duplicate the structure field name in the string,
just generate the string in the macro that's there anyway. To keep
the debugfs output the same, rename one (otherwise unused) field.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware API structs are split differently, synchronize
the struct splits with the current firmware definitions.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we want to trigger an NMI in the device, we need to set
bit 7 and not bit 0. However, older firmwares don't register
to the interrupt issued by bit 7. Use bit 7 first so that
the correct interrupt will be issued hoping that the firmware
will react. To be on the safe side, set bit 0 in case the
firmware didn't register to the proper interrupt.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the FW is in error status - try to read the RXF and
TXF (all of them) and add them to the dump data.

This shouldn't happen in non-error statuses, as we don't
want to stop the RXF/TXF while they are running.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some HW modules have two SRAMs. In such cases add the secondary SRAM to
the list of dumped segments.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As this functionality relies on getting a firmware notification
it is difficult to test. Allow accessing the data for it from
debugfs to be able to trigger all kinds of scenarios to test.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new host command can be used to configure the scheduler
instead of accessing the scheduler's registers from the
driver. This is easier and less error prone since accessing
the hardware at certain moments can lead to races with the
firmware.
Prefer to use the host command whenever it is available.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.

This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver doesn't support the firmwares that don't have
these capabilities. The code that actually used these
flags has been removed already, but the flags were left
for an unclear reason. Remove them.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Print the nvm version in the log for debugging purposes.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Fragmented scan should be applied for all channels, passive and active.
When scanning on passive channels the firmware uses frag_passive_dwell
to define the maximum continuous scan time before returning to the
operating channel. On active channels max_out_time is the parameter
used by the firmware to define the maximum time allowed out of the
operating channel. Since active channels' scan should also be fragmented
set max_out_time equal to frag_passive_dwell.
In addition:
- Set max_out_time and suspend_time if the firmware doesn't support
  fragmented scan to avoid unexpected behavior.
- Adjust max_out_time for second level of scan precedence.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This is to work around interoperability bugs with devices
that don't hanle MIMO properly.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_mvm_fw_dbg_collect allows to collect debug data from
the firmware. Most of the firmware interaction is done in
non-sleepable context. It makes little sense to force the
caller of iwl_mvm_fw_dbg_collect to sleep.
Defer the actual collection to a worker so that this
function will be able to be called from any context.
Reviewed-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In case platform is in d0i3 - make sure it is awake when
writing the registers to stop the monitor when collecting FW
debug data. Plus, remove unneeded mutex locking currently
done.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This option enables scan offload iteration complete notification from
firmware which includes the last iteration's status and the scanned
channels from the current iteration.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new config for 4165 series over PCI and insert support
for two new 4165 series PCI IDs.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes sure that we're not trying to read/write any of
the FW debug data collected during d0i3.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If Tx failed because the STA was in powersave there's no point
in sending a BAR so avoid indicating AMPDU_NO_BACK to mac80211.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Organize and cleanup the consts used by rs.
This is part of making some of these configurable.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make passive scan fragmentation depends on the number of active
interfaces. In case of single-MAC, make passive scan less fragmented.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to config the FW and to allocate monitor buffer driver should
run the function iwl_pcie_apply_destination immediately after FW sections
are loaded.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This configuration defines the ratio between number of scan iterations
where EBS is involved to those where it is not.
This configuration was left unconfigured due to inaccurate documentation.
Fix documentation as well.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Set the wakeup flag (of the d3 command) to configure the fw
to wakeup when sysassert happens while in d0i3.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new TLV supplies the ADMA address for SDIO mode, allowing
the driver to configure the default base address to be this
(as given in the FW), rather than hardcoding the values to
use until the FW sends the ALIVE message.

Use the value given by the FW in the IWL_UCODE_TLV_SDIO_ADMA_ADDR
TLV for setting the default SDTM base address until the FW sends
the ALIVE message. If it isn't given in the FW - use the current
hardcoded values.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A number of places (still) use a direct operation, use
iwl_mvm_sta_from_mac80211() consistently. In one place
also move it into the variable initializer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There are a few places not using it, use it at those places.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This device was renamed, but the external definition remained there.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some implementations (i.e. mini_rpm) assume the references
are managed only while the device is started.

Move the stale reference cleanup before stopping the
device in order to make them happy.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.

A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression t,f,d;
@@

-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver and the firmware now support 2 different channels
at the same time. Advertise this capability to the stack.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

On hw restart, make sure to wait for d0i3 exit
(by checking the IN_D0I3 status bit).

This is needed in order to avoid the stale
d0i3_exit_work from doing harm (e.g. unref
cleared reference).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Consider the iwlwifi module param d0i3_disable when
considering whether d0i3 is supported.

(There is currently no need to differentiate between
supported and enabled, so keep the function as-is)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enter d0i3 on suspend, and exit d0i3. Wait for the
command responses in both cases.

Use this mode in case of pcie trans.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow configuring additional d0i3 mode, in which the
fw will be configured to enter d0i3 only on suspend
(while keeping the wake_lock accounting as usual)

The d0i3 mode to use will be determined by the
underlying trans layer.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

d3 and d0i3 shouldn't be mutually exclusive. Set supported
wowlan triggers by looking for each of them, and check
on suspend/resume which flow should be used ("any" trigger
is supported by d0i3, and all the others by d3)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Implement the ref/unref trans ops and track both tx and
host command queues (and hold references while they
are not empty).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>